Jacuzzi 67661-5101 User manual

1
Questions, problems, missing parts? Before
returning to your retailer, call our customer service
department at 1-800-288-4002, 9 a.m. - 8 p.m.,
EST, Monday - Friday.
TUB FILLER FAUCET
Jacuzzi Item #NW55827
MODEL #67661-5101
ATTACH YOUR RECEIPT HERE
Serial Number ___________________
Purchase Date ___________________
2015/08/19 V1
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate, or install the product.
WARNING:
• Follow the installation instructions carefully. Proper installation is the installer’s responsibility.
• Failure to follow correct installation procedures can result in the faucet being loose, which can result in serious injury.
CAUTION:
• Check local building codes before beginning installation to ensure compliance.
PREPARATION
Before beginning the assembly of this product, make sure all parts are present. Compare parts with the package
contents and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 90 minutes (including removal of old faucet)
Tools Required for Assembly (not included): Adjustable Wrench, Silicone Sealant, Phillips Screwdriver, Pencil, Electric Drill

2
ASSEMBLY INSTRUCTIONS
Loosen the set screw (1) pre-assembled to the
spout (2), rotate the spout (2) about 90° to align
handle (3), then tighten the screw.
Place the escutcheon (1) over the standpipe (2)
and then push it to the base.
23
1
2
Drill a hole min 2 1/4 in. diameter-max 2 9/16 in.
diameter in the floor with an electric drill (1). Mark
the locations for the screws with a pencil (2). Then
drill three holes 1/4 in. diameter for the screws in
the floor with an electric drill (1).
Floor
Floor
1/4 in. dia.
1
1
23
2
2
1
Attach the mixer (1) to the standpipe (2), make sure
the prongs (3) on the standpipe (2) insert into the
hole (4) of the mixer (1). Install the set screw (5) and
tighten into the standpipe (2) with hex wrench.
Note: Do not to reverse the cold and hot supply lines.
Place the assembly with the flexible supply lines (1)
through the prepared hole and then holding the
escutcheon (2), secure the standpipe (3).
Note: If mounting into wooden floor, secure the
standpipe (3) using screws (4) only (wall plugs are
not needed). If mounting into solid floor, mark the
position of holes first and then secure the standpipe
(3) using anchors (5) and screws (4). Where requried
ensure correct anchors for your floor type are used.
4
3
2
Front
Cold inlet supply line Hot inlet supply line
1
3
4
5
5
1
2
5
3
4
6
1
2
4
3
Connect one end of the shower hose (1) to the mixer
(2) and the other end to the hand shower (3). Ensure
the washer (4) is in each end for seal.
4

3
ASSEMBLY INSTRUCTIONS
CARE AND MAINTENANCE
•
and void your warranty.
The manufacturer warrants this faucet to be free from defects in workmanship and material present at time of shipment
from the factory for a 90 days from the date of purchase. This warranty applies only to the original purchaser. The
manufacturer agrees to correct such defects at no charge or, at our option, replace the faucet with a comparable or
superior model. To obtain warranty service, call our customer service department at 1-800-288-4002 for return
authorization and shipping instructions. You may be required to present a copy of your sales receipt as proof of purchase.
All cost of removal and reinstallation are the expressed responsibility of the purchaser. Any damage to the faucet by ac-
, are the purchaser’s
responsibility. The manufacturer assumes no responsibility whatsoever for faucet installation during the warranty period.
There is no further expressed warranty. The manufacturer disclaims any and all implied warranties. The manufacturer shall
not be liable for incidental, consequential or special damages arising at or in connection with product use or performance
rights which vary from state to state. This warranty supersedes all prior warranties.
WARRANTY
Connect the flexible supply lines (1) to the water
supplies (2).
7
1
2
Flushing and checking for leaks
Important: After installation is completed, turn on the
hot and cold water supplies. Check for leaks. Flush
the water lines for one minute. Press the pin (1) to the
bottom position, and flush water lines for one minute.
This flushes away any debris that could cause damage
to internal parts. Check for leaks. After flushing, turn
the handles all the way off to shut off the water. The
pin (1) should now be in its normal position. Re-tighten
any connections if necessary, but do not overtighten.
8
1
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
There is a leak from under the handle
or there is a leak from aerator when
the faucet is off.
The cartridge is damaged. Remove the handle and replace the
cartridge.
Hand shower leaks or has a low flow
pattern.
Hand shower is dirty or damaged. Remove the hand shower and check
for any debris clogged at the shower
connection, check the hand shower’s
spray nozzle for any build up or debris.

4
For replacement parts, call our customer service department at
1-800-288-4002, 9 a.m. - 8 p.m., EST, Monday - Friday.
REPLACEMENT PARTS LIST
Printed in China
15
14
13
3
2
1
5
4
6
6
7
89
10
12
6
11
2
PART DESCRIPTION PART#
1 Hand Shower RP38132*
3 Shower Hose RP38236
4 Spout assembly RP80499*
5 O-Ring RP60107
6 Set Screw RP50002
7 Cartridge RP20063
8 Bonnet RP70015
9 Cap RP80008*
10 Screw RP50049
11 Handle RP13422*
12 Index RP80390*
14 Screw RP50037
13 Escutcheon RP80500*
15 Anchor RP50036
2 Washer RP64219