Koden CVS-1410B User manual

Declaration of Conformity
(As referred to in Annex IV 2. of Directive 2004/108/EC)
Declares under his sole responsibility that the produced Echo Sounder manufactured by
Koden Electronics Co., Ltd.
5278 Uenohara
Uenohara-Shi,
Yamanashi-Ken
409-0112, Japan
Telephone [phone] Telefax [phone]
Identified by the type number CVS-1410B to which this declaration refers conforms to the
relevant essential requirements of Directive 2004/108/EC and is in conformity with the EMC
requirements of EU harmonised standard
EN 60945: 2002 ( Clauses 9,10 & 12 )
Authorised representative in Europe
Heinz Hoghoff
Koden Elektronik GmbH.
Am Gewerbepark 15
D-64823, Gross–Umstadt
Germany.
Phone [phone]
Telefax+49 6078 73824
Signed :
Heinz Hoghoff,
Dated : 26 Apr. 2011 Document No. 71-2731U-X001
N.B. As this product is for Maritime use compliance with Directive 72/23/EEC is not required.

CVS-1410B RevisionHistory
0093114105-03 i
CVS-1410B Operation Manual
Doc No. 0093114105
Document Revision History
No. Doc. No-Rev. No. Date
Revised
(Y/M/D)
Revised Content
0 0093114105-00 2011/10/12 First edition
1 0093114105-01 2012/02/10 Important Notice, Chapter 1, Chapter3, Chapter 6
2 0093114105-02 2012/11/29 Change the frequency, Chapter 2, Chapter3, Chapter 6
Cover
3 0093114105-03 2013/09/11 Revision (From software KM-F13 Ver01.05 to Ver01.**)
4
5
6
7
8
9
10
Document No. Revised Version Norm
When part of the document needs to be revised, the document has advanced revision number.
The document No. is indicated at the lower right side on the cover and at the left or right side of the
footer region of each page.
© 2011-2013 Koden Electronics Co., Ltd. All rights reserved.
No part of this publication may be reproduced, transmitted, translated in any from by any means
without the written permission of Koden Electronics Co., Ltd. The technical descriptions contained in
this publication are subject to change without notice. Koden assumes no responsibility for any errors,
incidentals or consequential damages caused by misinterpretation of the descriptions contained in this
publication.

CVS-1410B RevisionHistory
0093114105-03 i
CVS-1410B Operation Manual
Doc No. 0093114105
Document Revision History
No. Doc. No-Rev. No. Date
Revised
(Y/M/D)
Revised Content
0 0093114105-00 2011/10/12 First edition
1 0093114105-01 2012/02/10 Important Notice, Chapter 1, Chapter3, Chapter 6
2 0093114105-02 2012/11/29 Change the frequency, Chapter 2, Chapter3, Chapter 6
Cover
3 0093114105-03 2013/09/11 Revision (From software KM-F13 Ver01.05 to Ver01.**)
Chapter 5
4
5
6
7
8
9
10
Document No. Revised Version Norm
When part of the document needs to be revised, the document has advanced revision number.
The document No. is indicated at the lower right side on the cover and at the left or right side of the
footer region of each page.
© 2011-2013 Koden Electronics Co., Ltd. All rights reserved.
No part of this publication may be reproduced, transmitted, translated in any from by any means
without the written permission of Koden Electronics Co., Ltd. The technical descriptions contained in
this publication are subject to change without notice. Koden assumes no responsibility for any errors,
incidentals or consequential damages caused by misinterpretation of the descriptions contained in this
publication.

Important Notice CVS-1410B
ii 0093114105-03
Important Notice
For copy and transcription of this Operation Manual (hereinafter referred to as this manual),
permission from Koden is needed. Koden prohibits the un-authorized copy and transcription of
this manual.
If this manual is lost or damaged, consult a dealer of Koden or Koden.
The specification of the products and the contents in this manual are subject to change without
notice.
The contents displayed on the menu of product may be different from the expression of this
manual. The fonts and shapes of the keys and menus in the illustration may differ from the actual
ones, and some parts may be omitted.
Koden is not liable for damages and troubles arisen from misunderstanding of the contents in this
manual.
Koden is not liable for any damages caused by earthquake, lightning, wind and flood damage and
fire for which Koden is not responsible, and actions by third parties, other accidents, customer’s
unintended error/abuse and the use under other abnormal conditions.
Koden is not liable for damages of accompaniment (change/loss of memorized content, loss of
business profit, stop of business) arisen from use or failure of our products.
If the stored data are changed or lost, irrespective of causes of troubles and damages, Koden is
not liable for them.
Koden is not liable for any damages arisen from malfunction caused by combination of software
and connected equipment in which Koden is not engaged.

CVS-1410B For Your Safe Operation
0093114105-03 iii
For Your Safe Operation
Pictorial used in this Operation Manual
This Operation Manual uses the following pictorials. Understand the meaning of each pictorial and
implement the maintenance and inspection.
Symbol Meaning
Mark for warning
This symbol denotes that there is a risk of death or serious injury when not
dealing with it correctly.
Mark for danger high voltage
This symbol denotes that there is a risk of death or serious injury caused by
electric shock when not dealing with it correctly.
Mark for caution
This symbol denotes that there is a risk of slight injury or damage of device
when not dealing with it correctly.
Mark for prohibition
This symbol denotes prohibition of the specified conduct. Description of the
prohibition is displayed near the mark.
Caution Item on Equipment
Be careful of a high voltage inside.
A high voltage, which may risk your life, is used. This high voltage remains
in the circuit after you have powered off switch. To prevent touching the high
voltage circuit inadvertently, the hard cover is provided to the high voltage
circuit and the high voltage caution label is affixed. Ensure to power off
switch for your safety and discharge the electricity remaining in the capacity
before starting to check. An engineer authorized by our company should
inspect and maintain
Be sure to power off in the boat.
If the power switch is inadvertently powered on during work, you will be
electrified. To prevent such accident from occurring, ensure to power off in
the boat and the power of equipment. Furthermore, it is safer to hang the
caution tag described as [Under Work] near the power switch of equipment.
Be careful of dust
Inhaling dust may cause A respiratory disease. When cleaning the inside of
equipment, be careful not to inhale dust. Wearing a safety mask is
recommended.

For Your Safe Operation CVS-1410B
iv 0093114105-03
Caution on location of equipment
Do not install the equipment where it is excessively damp and suffers from
excessive water drops.
Escaping from static electricity
The static electricity may be generated from the carpet on the floor in the
cabin or clothes made of synthetic fiber. The static electricity may destroy
the electronic parts on the circuit board. Handle the circuit board, taking the
measure of static electricity free.
Install the transducer at the location where it is not affected by bubble and
noise The bubble and noise seriously degrade the performance of this unit.
Caution Item on Handling
Do not disassemble or modify. It may leads to trouble, fire, smoking or
electric shock. In case of trouble, contact our dealer or our company.
In case of smoke or fire, boat power off and the power of this unit. It may
cause fire, electric shock or damage.
Be cautious of remaining high voltage.
A high voltage may remain in the capacitor for several minutes after you
have powered off. Before inspecting inside, wait at least 5 minutes after
powering off or discharge the remaining electricity in an appropriate manner.
Then, start the work.
The information displayed in this unit is not provided directly for your
navigation. For your navigation, be sure to see the specified material.
Use the specified fuse. If un-specified fuse is used, it may cause a fire,
smoke or damage.
Whenever transmitting, be sure to submerge the transducer in water first. If
transmitted without submerging the transducer, it may be damaged.

CVS-1410B Contents
0093114105-03 v
Contents
Document Revision History ......................... i
Important Notice ......................................... ii
For Your Safe Operation............................ iii
Contents .....................................................v
Introduction................................................ ix
System Configuration ................................. x
Configuration of Equipment ....................... xi
Change the frequency ............................. xiv
Chapter 1 Basic Operation ......................1-1
1.1 How to use the key .................... 1-1
1.2 Power On/Off ............................. 1-2
Power on.................................... 1-2
Power off.................................... 1-2
Alarm of Power Voltage ............. 1-2
1.3 LCD Brilliance Adjustment ......... 1-3
Adjustment of LCD Brilliance ..... 1-3
Brightness Adjustment of Panel
Brilliance .................................... 1-3
1.4 Switch-over of Display mode ..... 1-3
Normal Image (Low frequency,
High frequency).......................... 1-3
Dual frequency........................... 1-4
Zoom (Low frequency, High
frequency) .................................. 1-4
Navigation Menu (NAV1, NAV2) 1-6
1.5 Selection of NAV Display ........... 1-7
Type of NAV Display .................. 1-7
Selection of NAV Menu .............. 1-7
1.6 Switch-over of Range ................ 1-8
Setting the range switching to auto
range.......................................... 1-8
Setting the range switching to
Manual range ............................. 1-8
1.7 Setting of Shift............................ 1-8
Setting of Manual Shift............... 1-8
Release of manual Shift............. 1-9
Setting of Auto Shift ................... 1-9
1.8 Gain Adjustment....................... 1-10
TVG.......................................... 1-10
1.9 Use of [EVENT] key ................. 1-10
Selecting the event key
function .................................... 1-11
Presetting the waypoint ........... 1-11
Store the image........................ 1-12
Fishing hot spot........................ 1-12
1.10 Use of [F1] / [F2] key................ 1-13
Selecting the
[F1] / [F2] key ........................... 1-13
Preset of [F1] / [F2] key ........... 1-13
1.11 Operation of VRM .................... 1-13
1.12 Display of fish information........ 1-14
Display the fish symbol / Stop the
display of fish symbol............... 1-14
Selecting the symbol info......... 1-14
Fish symbol detection
adjustment ............................... 1-15
Size adjustment ....................... 1-15
Big fish / Big fish color ............. 1-15
Points to note in use of fish
symbol...................................... 1-16
Chapter 2 How to use the menu ............. 2-1
2.1 How to operate the menu .......... 2-1
Display the menu / Stop the
display of menu.......................... 2-1
Menu Operation ......................... 2-1
2.2 Changing of Image Speed ......... 2-2
2.3 Rejection of Interference............ 2-2
Interference Rejection................ 2-2
2.4 Color Rejection of Weak Echo... 2-3
Color Rejection .......................... 2-3
2.5 Rejection of Noise...................... 2-3
Noise Rejection.......................... 2-3

Contents CVS-1410B
vi 0093114105-03
2.6 Setting of Shift step ....................2-3
2.7 Selection of Zoom ......................2-3
2.8 Setting of Zoom Range ..............2-4
2.9 Setting of Zoom Start .................2-4
2.10 Preset of Range .........................2-4
Easy registration method of the
range ..........................................2-5
2.11 Setting of Background Color ...... 2-5
2.12 Setting of White Line ..................2-5
2.13 Setting of Alarm..........................2-6
Stopping the alarm sound ..........2-6
Setting the alarm ........................2-7
Release the alarm ......................2-7
Confirm the alarm state..............2-7
2.14 Preset/ WPT edit/ WPT delete of
Waypoint.................................... 2-8
NAV Start.................................... 2-8
Cancel the NAV ..........................2-8
Edit the destination..................... 2-8
Delete the waypoint....................2-9
Recall the stored image and
preset it as a destination ............ 2-9
2.15 Store/Recall/Deletion of Image 2-10
Store the image ........................2-10
Recall the stored image ...........2-10
Delete the stored image........... 2-11
Add the comment to the stored
image........................................ 2-11
2.16 Explanation of Sona-ToneTM.....2-12
Switch-over of Sona-ToneTM.....2-12
Connection of External
Speaker ....................................2-12
2.17 Explanation of Menu Item ........2-12
Inner-hull ..................................2-12
Change the TX power ..............2-13
Change the Pulse width ...........2-13
Change the Bandwidth.............2-13
D.Range ...................................2-14
Display Width ...........................2-14
Display the A scope / Stop the
display of A scope .................... 2-14
Change the display color of echo
sounder image .........................2-14
Change the depth value...........2-14
Display the depth unit / Stop the
display of depth unit .................2-14
Display the water temp graph /
Stop the display of water temp
graph ........................................2-15
Setting of the background color of
NAV display .............................. 2-15
Setting of the echo sounder
display at NAV display..............2-15
Image Swap .............................2-15
Display the Operation guide /
Stop the display of Operation
guide.........................................2-15
Display the detection area /
Stop the display of detection
area ..........................................2-15
Setting of Scale display............2-16
Change the scale value............2-16
Change the image direction .....2-16
Setting of Depth measurement 2-16
Change the display color..........2-16
Setting of Key lock ...................2-16
Sub Depth Value ......................2-17
Change the User setting .......... 2-17
Change the scale type .............2-17
Change the bottom color.......... 2-17
Change the image partition...... 2-17
Display the Frequency /Stop the
display of Frequency ................2-17
Selecting a display area of fish
symbol indication......................2-18
Chapter 3 How to use the menu2............3-1
3.1 Display of Menu .........................3-1

CVS-1410B Contents
0093114105-03 vii
Display the menu ....................... 3-1
Return to the normal menu ........ 3-1
3.2 Setting of External Input/Output. 3-1
Buzzer Setting............................ 3-1
Temp Source.............................. 3-1
Speed Source ............................ 3-1
Baud Rate .................................. 3-1
NMEA Monitor............................ 3-2
NMEA Output Data .................... 3-2
External synchronous input ....... 3-2
3.3 Setting of Correction Item .......... 3-2
Draft Set..................................... 3-2
Sonic Speed............................... 3-2
Water Temp................................ 3-2
Boat Speed ................................ 3-3
Directivity angle (Low/High) ....... 3-3
Bubble........................................ 3-3
3.4 Setting of Basic Set Item ........... 3-3
Language ................................... 3-3
Range & Speed Unit .................. 3-3
Depth Unit .................................. 3-3
Temperature Unit ....................... 3-3
Local time Offset ........................ 3-3
GPS select ................................. 3-3
GPS initialize.............................. 3-3
3.5 Maintenance Menu .................... 3-4
Simulation .................................. 3-4
Slide show.................................. 3-4
Initialize ...................................... 3-4
System Check............................ 3-4
All WPTs deletes ........................ 3-4
All stored image deletes ............ 3-4
Bottom start................................ 3-4
Past image ................................. 3-4
Inner-hull .................................... 3-4
TD select.................................... 3-4
3.6 Setting of Adjust2 Item............... 3-5
STC strength adjust Low / High. 3-5
STC depth adjust Low / High ..... 3-5
Color adjust................................ 3-5
Image speed adjust.................... 3-5
Bottom limit ................................ 3-5
Sounding.................................... 3-5
3.7 Frequency Select....................... 3-6
Frequency select (Low/High) ..... 3-6
Power frequency adjustment ..... 3-6
Chapter 4 Maintenance and Inspection .. 4-1
4.1 Inspection................................... 4-1
4.2 Cleaning..................................... 4-1
Display unit ................................ 4-1
Transducer ................................. 4-1
4.3 Fuse Replacement..................... 4-2
4.4 If you suspect a trouble.............. 4-2
4.5 Diagnostic Test........................... 4-3
Diagnose.................................... 4-3
Confirm the version.................... 4-3
Return to the menu .................... 4-3
Chapter 5 Installation .............................. 5-1
5.1 Items of Caution on Installation . 5-1
Unpacking the components ....... 5-1
Inspection of components and
accessories ................................ 5-1
Decision of Installing Location ... 5-1
Laying and Connection of
Cable.......................................... 5-2
Confirmation after Installation .... 5-2
5.2 Installation of Display unit .......... 5-3
Desk-top Installation .................. 5-3
Flush-mount Installation............. 5-5
5.3 Installation of Transducer........... 5-6
In case of Inner-hull ................... 5-6
5.4 Wiring......................................... 5-7
Connection of Cable to Display
unit ............................................. 5-7
Pin Assignment of Rear
Connector .................................. 5-8
Connection of Power Cable ....... 5-9

Contents CVS-1410B
viii 0093114105-03
Connection of Transducer .......... 5-9
Connection with external echo
sounder ....................................5-10
Connection with external
navigation equipment ...............5-10
Connection with Speed Sensor or
Water Temperature Sensor
(Option) .................................... 5-11
Connection of External Speaker
for Sona- ToneTM (J2)
(Prepared by a customer) ........5-12
Connection of External Monitor
(J5) (Prepared by a customer) .5-12
5.5 Serial Data................................5-13
Input Data.................................5-13
Output Data..............................5-13
Chapter 6 Table Attached........................ 6-1
6.1 Menu List....................................6-1
6.2 Specification ...............................6-5
6.3 Dimensions ................................6-6

CVS-1410B Introduction
0093114105-03 ix
Introduction
The CVS-1410B is a Dual frequency Color LCD display echo sounder.
This unit equipped with digital process displays the circumstance in the water under all conditions,
matching with the high luminance 10.4 inch LCD.
The main features of this unit are as follows:
●With the digital reception process, the compatibility of the high resolution in a shallow depth and the
noise rejection capability in a deep depth are established. The auto mode function provides the best
image.
●The high-performance LCD maintains high visibility under any conditions.
●The unit can be installed in an open bridge and is highly waterproof.
●Sona-Tone (Sonar sound) function is equipped with for catching situations schools of fish and
others by sound.
●Up to 10 images can be stored. If you connect the optional GPS, the fishing hot spot function, that
directs your boat to navigate easily to the location desired, is available by marking the event mark
when recalling the stored image.
●With the adoption of a specific filter (AR coat), an image can be seen clearly, refusing sunshine.
The countermeasures against the reflection on the LCD screen and dew are provided. This display
has a high level of visibility under all operation conditions.
●The various alarm functions are available. (Bottom, school of fish, water temperature*, board
speed*, arrival*, XTE*, power) (Note: The mark * denotes that the connection of option is
mandatory)
●When flush-mounting, the unit can be easily installed from front side.
●The RGB output for an external monitor is provided as standard equipment. The use of the external
monitor enables you to observe easily the echo sounder screen at a location which is remote from a
main unit. (External monitor: Prepared by a customer)
CVS-1410B is the high sensitivity model with broadband transducer. This model can be used at
your optimum frequencies within the specification of the broadband transducer. You can set 2
frequencies depending on a target fish or intended purpose during operation.

System Configuration CVS-1410B
x 0093114105-03
System Configuration
Connection Diagram
White
Black
+
-
POWER
connecto
r
J6 connector
J5 connector
External monito
r
CW-576-0.5M
(Owner supply)
CW-269A-2M
10.8 to 31.2VDC
External speaker
(For speaker with amplifier)
CW-264A-2M (Owner supply)
J2 connector
External echo sounder
CW-371-5M
CW-372-5M
(Owner supply)
J1 connector
NMEA circuit input output
CW-373-5M
CW-374-5M
CW-375-5M
CW-376-5M
External navigation equipment
J3 connector
GPS sensor
CVS-1410B Display unit
With mounting bracket and hard cover
Standard configuration
Option
Owner supply
Legend
Transducer TDM-071 (38 to 75 kHz)
Transducer TDM-091D (42 to 65 kHz) (130 to 210 kHz)
Urethane mold made. Equipped with Ship’s bottom/Ship’s side.

CVS-1410B Configuration of Equipment
0093114105-03 xi
Configuration of Equipment
Standard Equipment Configuration List
No Name of item Type Remark Weight/
Length Quantity
1 Display unit
CVS-1410B With mounting
bracket and knob 7.5 kg 1
2 Hard cover
A30MB10250 390 g 1
3 DC power cable
CW-269A-2M With 5P connector
and one end plain 2 m 1
4 Fuse
F-7161-3A
Cylinder (ø 6.4x30)
Normal fusion type
for main power 2
5 Transducer Refer to next page “Type of
transducer”
Transducer cable
(with connector at
one end)
1
6 Operation Manual CVS-1410B.OM.E English 1
7 Quick Reference CVS-1410/1410HS.QR.E English 1
8 Cautionary Note CVS-SER.RM.E English 1

Configuration of Equipment CVS-1410B
xii 0093114105-03
Type of transducer
No Specification Frequency Material /
Length of
the cable
Mounting method Beam width
(Right and left x
back and forth)
1
TDM-071
38 to 75 kHz
1 kW
Urethane
mold
15m
Ship’s bottom/
Ship’s side
38kHz
30°x20° ( -6dB)
75kHz
16°x 10° ( -6dB)
2
TDM-091D
42 to 65 kHz
130 to 210kHz
1 kW
Urethane
mold
15m
Ship’s bottom/
Ship’s side
42kHz
35° ( -6dB)
65kHz
22° ( -6dB)
130kHz
14° ( -6dB)
210kHz
8° (-6dB)
Caution: For Inner-hull installation, an Inner-hull kit is necessary.

CVS-1410B Configuration of Equipment
0093114105-03 xiii
Option List
No Name of Item Specification Remark Weight/Length
1 Water temperature
sensor/speed sensor
ST-80 For transom mounting
Plastic made (with cable) 0.3 kg / 9 m
ST-90 For through-hull mounting
Plastic made (with cable) 0.6 kg / 9 m
ST-100 For through-hull mounting
Bronze made (with cable) 1.2 kg / 9 m
2 Inner-hull kit MFB-04W Plastic made for installing the
transducer TD-501C 1.3 kg
3 Connecting cable
CW-371-5M With 5P connector and 5P
water resistant connector
5m
CW-372-5M With 5P water resistant
connector and one end plain
5m
CW-373-5M 6P water resistant connectors
at both ends
5m
CW-374-5M With 6P connector and 6P
water resistant connector
5m
CW-375-5M 6P water resistant connectors
at both ends
5m
CW-376-5M With 6P water resistant
connector and one end plain
5m
CW-154A-5M With 6P connector and one
end plain
5m
CW-264A-2M With 12P water resistant
connector and ø 3.5 Stereo
jack
2m
4 Cable for external
monitor CW-576-0.5M
With 10P water resistant
connector and D-Sub
connector
0.5 m
5 Connector LTWBD-05BFFA-L180 5P water resistant connector
LTWBD-06BFFA-L180 6P water resistant connector

Change the frequency CVS-1410B
xiv 0093114105-03
Change the frequency
CVS-1410B is used with the other transducer please make sure to set the below items manually in line
with the transducer installed.
Caution: The transducer may be damaged if the settings are wrong.
Caution: There are occasions too much noise is generated in a particular frequency to
be connected.
Caution: Fish symbol operation cannot be generated at the other frequencies than the
high frequency of 200 kHz and the low frequency of 50 kHz.
Setting of Output Frequency
1 Press the [MENU] key.
2 Select [Freq] [Freq select (L)]. (See [2.1 How to operate the menu])
3 Press the [ ] key.
4 Set the output frequency at the low frequency side. (Press the [ ] key or [ ] key)
5 Set the high frequency also in the same way as for the low frequency side, in reference to the step
2 to 4.
6 Press the [MENU] key. Then, the edit is finished.
Caution: When single transducer is connected, set the same frequencies for low and
high.
Setting of Power Frequency
1 Press the [MENU] key.
2 Select [Freq] [Power freq adj]. (See [2.1 How to operate the menu])
3 Press the [ ] key.
4 Set the power supply frequency. (Press the [ ] key or [ ] key)
The recommended power supply frequency for Dual frequency (50 kHz/200 kHz): 107.0 kHz
Transmit
frequency
Recommended
power supply
frequency
Transmit
frequency
Recommended
power supply
frequency
28 kHz 115.0 kHz 70 kHz 106.5 kHz
38 kHz 105.0 kHz 75 kHz 103.5 kHz
40 kHz 123.0 kHz 120 kHz 109.0 kHz
55 kHz 107.0 kHz - -
Caution: There may be much noise on the screen even for the recommended power
supply frequency depending on the transducer. In this case, set the power
supply frequency to reduce the noise on the screen.
Caution: Set the power supply frequency to reduce the noise on the screen, when the
other transmission frequency than above is used.
5 Press the [MENU] key. Then, the edit is finished.

CVS-1410B Change the frequency
0093114105-03 xv
Adjustment of bottom detection
When the bottom can't be detected or when the bottom is of mud pool or seaweed, [Gain (TD)] shall be
turned up. When transfer to fish schools, etc. frequently occurs, [Gain (TD)] shall be turned down.
1 Press the [MENU] key.
2 Select [Adjust] [Gain (TD)]. (See [2.1 How to operate the menu])
3 Press the [ ] key. The image displays bottom only. It may show very strong fish targets.
4 Set a value to display the sea bottom continuously without interruption. For high frequency, turn
[GAIN (HF) knob] and for low frequency, turn [GAIN (LF) knob]
After the alteration of setting, please confirm the condition for some time.
Those adjustments are recommended to be performed at the site of use.
5 Press the [MENU] key. Then, the edit is finished.
Gain (TD)
Bottom
Gain (TD) L Gain (TD) H
L: 6.0 H: 6.0 R:M 12.0V

CVS-1410B Chapter 1 Basic Operation
0093114105-03 1-1
Chapter 1 Basic Operation
1.1 How to use the key
CVS-1410B Display unit
Various setting can be done directly. The menu list closes automatically after the key operation of the
other keys than [menu].
No. Key Name Explanation
1 [F1] Recalls directly the item preset.
2 [EVENT] Notifies the external equipment of the present position. Presets
the menu. It begins a fishing hot spot.
3 [Cursor]
▲▼
Selects the menu item. Changes the set value.
Moves the VRM marker. IMoves the marker for notifying the
event.Changes the shift.
4 [MENU] Opens or closes the menu.
5 [F2] Recalls directly the item preset.
6 [RANGE ] Changes the range setting.
7 [GAIN(HF)
Knob]
Rotate: Changes the gain value.
Press: Recalls the gain select.
8 [GAIN(LF)
Knob]
Rotate: Changes the gain value.
Press: Recalls the gain select.
9 Switches to the High frequency or Low frequency of echo
sounder image, zoom and navigation menu.
10 [BRILL ]/
Power
Press: Power on. Adjusts the brilliance and brightness of panel.
Long-press: Power off.
1
2
4
5
6
7
8
9
10
3
[DISP]

Chapter 1 Basic Operation CVS-1410B
1-2 0093114105-03
1.2 Power On/Off
Power on
1 Press the [BRILL ] key to power on.
The startup menu is displayed. When
started up, the internal memories (ROM,
RAM) are automatically checked. When
checking is normally finished, the menu
below is displayed.
Caution: If an error occurs in the memory
check, the LED on the operation panel
blinks. The unit may be not function
normally. If you suspect trouble,
contact the dealer of your purchase or
our company.
2 Language Selection at Initial Startup.
When powering on first, the [Language] menu is
displayed.
Select the language with [ ]key or [ ]key.
(The language can be selected by rotating the
[GAIN (HF) Knob] or [GAIN (LF) Knob].)
3 When the installation of a transducer is
[Inner-hull], select the [Yes].
Press [ ] and [ ] keys in sequence, and select
the [Yes].
4 Press the [MENU] key to decide the
language and the inner-hull.
5 After a few seconds, the menu sets the
screen as selected in [DISP].
Caution: In addition to English, Japanese,
there are several compatible
languages.
Explanation of the display:
Type of Gain
H: High frequency gain
L: Low frequency gain
Type of Range
R: M: Manual Range
R: A: Auto Range
R: AS: Auto Shift
Power off
1 When powering off, keep pressing the
[BRILL ] key for 3 seconds.
The remaining time for the power to shut off
is displayed on the menu.
Alarm of Power Voltage
If detecting the malfunction of the voltage, the
icon blinks and the alarm beeps.
Caution: In case of the low voltage or the
high voltage, it shuts down. The
precision of Power Voltage is ± 0.5 V.
CVS-1410B
Language
English
日本語
Inner-hull
No
Yes
Rainbow pattern
Time mark
Gain Range
A
larm icon
Fish
Schools of fish
Oscillation line
Depth
L H
Power supply voltage
Function icon
Event icon