MacDon M1170 Parts list manual

M1170 Windrower Quick Card - Form 214522 Rev. B
Supplement to M1170 Windrower Operator’s Manual
M1170 Windrower Operator’s Staon Features M1170 Windrower Operator’s Staon Features
Subject to change without notice
Ground Speed Lever (GSL) Buons
Callout Funcon
A Reel speed / disc speed
B Back
C Select
D Autosteer engage (if installed)
E Reel posion
F One-Touch-Return presets
G Header posion
H Shi
J Scroll wheel and select
Operator Console Buons
Callout Funcon Callout Funcon
A Double window aachment (DWA) / swath roller
aachment raise/lower N High beams
B Deck shidraper right side deliver P Windshield defog/defrost
C Deck shidraper center delivery Q Air condioning
D Deck shidraper leside delivery R Temperature
E Draper / double windrow aachment (DWA) speed S Blower speed (manual mode)
F Harvest performance tracker (HPT) shortcuts T Horn
G Cab-forward field lights U Auto fan speed
H Beacon lights V Cab air recirculaon
J Turn signals W Eco Engine Control (EEC)
K Hazard light X Windshield wiper (rear)
L Clearance lights Y Wiper fluid (front and rear)
M Road lights Z Windshield wiper (front)
Harvest Performance Tracker (HPT) Display
Callout Funcon
A Sokeys 1–4 (opens run pages 1–4)
B Home (returns to the last run page)
C Scroll and select (scrolling highlights menu opons, pressing knob ac-
vates selecon)
D Back (moves up one level in menu structure)
E Main menu (accesses windrower and header sengs)
1. Lock operator’s seat in either cab-forward or engine-forward posion, GSL in
PARK, and HEADER DRIVE switch OFF.
2. Put your seat belt on. Set throle to LOW IDLE posion (fully back).
3. If HPT is sll boong up, allow the Wait to Start (WTS) symbol to disappear before starng
the engine.
4. Sound horn three mes.
5. Turn ignion key to START posion unl engine starts, release key, and idle engine unl
temperature reaches 40°C (104°F). HPT displays MacDon logo for 16 seconds before
switching to the header disengage page.
Normal Start – Engine Temperature above 15°C (60°F)
Operator Console Features
Callout Funcon Callout Funcon
A Auxiliary power outlets D Header drive
B USB jack E Header drive reverse
C Ignion F Throle
Ground Speed Lever (GSL) Shortcuts
Buons Funcon
Shi+ back Home page
Shi+ select Main menu access
Shi+ scroll Adjust maximum ground speed
Easily acvate the turn signals when transporng by using
the REEL/DISC SPEED +/- buons on the GSL.
Pro Tip
Console Funcon Buon Shortcuts
Buon Shortcut
F1 Float menu
F2 One-Touch-Return
F3 Windrower sengs
F4 Header sengs

Ongoing Maintenance Intervals
Time Service
Every
10 hours or
daily
Check re inflaon.
Check engine oil level.
Check engine coolant level at reserve tank.
Check hydraulic oil level.
Drain fuel filter water trap.
Fill fuel tank.
Check hydraulic hoses and lines for leaks.
Check diesel exhaust fluid (DEF) level.
Every
50 hours
Grease caster pivots (x2).
Grease top lilink pivots (x4).
Grease caster wheel bearings.
Clean cab fresh air intake filter.
Check gearbox oil level.
Every 100
hours or
annually
Clean cab air return filter.
Clean radiator, hydraulic oil cooler, charge air cool-
er, and A/C condenser.
Every 250
hours
Change engine oil and filter.
Change engine gearbox oil.
Change air cleaner primary filter.
Check wheel drive oil level.
NOTE: Refer to M1170 Operator’s Manual for service beyond
250 hours.
Break-In Inspecons
Hr(s) Item Check
1 Drive wheel nuts Torque: 510 Nm (375 lbf·) dry
Refer to M1170 Operator’s Manual.
5
A/C compressor belt Tension
Caster wheel nuts Torque: 170 Nm (125 lbf·)
Caster wheel an-shimmy
dampener bolts
Torque bolts:
Inboard (x2): 135 Nm (100 lbf·)
Outboard: 244 Nm (180 lbf·)
Outboard jam nut: 135 Nm (100 lbf·)
Walking beam width
adjustment bolts Torque: 759 Nm (560 lbf·)
10 Walking beam width
adjustment bolts
50
Hose clamps: air intake,
radiator, heater and
hydraulic
Hand-ghten unless otherwise noted.
Walking beam width
adjustment bolts Torque: 759 Nm (560 lbf·)
Caster wheel an-shimmy
dampener bolts
Torque bolts to the same specificaon
as 5 hour check.
Main gearbox oil
Change
Drive wheel oil lubricant
Hydraulic return filter
Hydraulic charge filter
Torque: 759 Nm (560 lbf·)
Tire Pressures
The recommended re pressure will vary depending on header type
and aachments installed. Refer to your M1170 Operator’s Manual
for a complete list of recommended re pressures.
M1170 Maintenance and Servicing
Subject to change without noce
Harvest Performance Tracker (HPT) Menu Structure
M1170 Windrower Quick Card - Form 214522 Rev. B
Supplement to M1170 Windrower Operator’s Manual
Fluids and Lubricants
Fluid Capacity Spec Descripon /
Informaon
Diesel
exhaust fluid
(DEF)
28 L
(7.5 US Gallons)
Must meet
ISO 22241
requirements
Diesel exhaust
system
Fuel:
diesel No.2
518 L
(137 US Gallons)
ASTM
D-975
Grade S15
Sulphur (by weight)
0.5% max.
water and sediment
(by vol) 0.05% max.
lubricity 520 microns
Fuel: diesel
no.1 and no. 2
mix
518 L
(137 US Gallons) n/a
Sulphur (by weight)
0.5% pref. 1% max. water
and sediment (by weight)
0.1% max. lubricity 460
microns
Engine
coolant
30 L
(7.9 US Gallons)
ASTM D-6120 and
Fleetguard ES Com-
pleat®
Refer to M1170
Operator’s Manual
Standard: 1.4 L
(1.5 US Quarts)
SAE 75W-140 (or 80W
-140) API service class
GL-5 Fully synthec gear lubri-
cant (SAE J2360 preferred)
High Torque: 4.5 L
(4.8 US Quarts)
SAE 85W-140, API
service class GL-5
Grease As required SAE
mul-purpose
High temperature extreme
pressure EP2. max 1%
molybdenum disulphide,
lithium base unless
otherwise noted
Engine oil 11 L
(11.6 US Quarts)
SAE 15W-40 for API
class SJ and CJ-4 Engine oil pan
Hydraulic oil 60 L
(15.8 US Gallons)
Hydraulic
transmission oil Refer
to operator’s manual
Windrower drive and head-
er drive
Gearbox oil 2.1 L
(2.2 US Quarts)
SAE 75W-140 (or 80W
-140) API service class
GL-5
(SAE J2360
preferred)
Fully synthec gear lubri-
cant for
engine gearbox
A/C
refrigerant 2.27 kg (5 lb.) R134A Cab A/C system
A/C
compressor
oil
240 cc
(8.1 fl. oz)
SP-15
PAG
Cab A/C compressor lubri-
cant
Wheel Drive
lubricant
QuickMenu Features
• Adjust float • Set knife speed • Access maintenance informaon
• Adjust Eco Engine Control (EEC) speed • Adjust auto speed sengs • Manage telltales
• Set maximum ground speed • Define header alarm speeds • Turn auto speeds ON/OFF
• Set header alarm pressure
Informaon: Contains informaon about the windrower, header, and
performance data.
Sengs: Provides access to adjustable sengs for the display,
windrower, header, and One-Touch-Return.
Maintenance:
Contains the maintenance scheduler. Turn ON/OFF
individual maintenance noficaons and log your
maintenance history.
Diagnoscs: Provides access to diagnosc informaon, engine
faults, and windrower faults.
Engine
Aertreatment:
Provides access to the selecve catalyc reducon (SCR)
catalyst condioning MANUAL (FORCE) and INHIBIT
switches.
Pressing the encoder knob (A) (or the SELECT buon on the GSL) opens the QuickMenu on the HPT display. The QuickMenu is the main way to adjust
on-screen values. Adjustable parameters are highlighted by a white border (B). The curser posion is highlighted with a red border (C). Use the
encoder knob to move the red curser to the desired area. Press SELECT to access the adjustment (D). Once the parameter is selected, use the scroll
wheel to change the value. Press BACK or HOME to save the adjustment.
QuickMenu