National Alloy User manual

Assembly Instrucon
Telephone [phone]
Fax [phone]
www.NationalOfficeFurniture.com
Part # 2891776
Rev, A
Printed in U.S.A
© 2014 Kimball International, Inc.
Alloy
Ganging Jumper
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call National Customer Service 800.482.1717.
Package Contents
1Verify that the powered beam and ganging kit are completely installed
and the two units to be ganged together. For Fixed Height ganging skip to
step 3. For Adjustable Height connue to step 2.
2Run the jumper through the wire pass-through on both crosslink rails.
Connect one end of the ganging jumper to the rst powered beam phase
block. Connect the opposite end of the ganging jumper to the rst phase
block on the second unit. (Figure A)
Qty
Ganging Jumper 1
3Connect one end of the ganging jumper to the rst powered beam open
phase block connecon. Connect the opposite end of the ganging jumper
to the rst open phase block connecon on the second unit.
Note: Verify all connecons have been fully seated and “clicked”
into proper posion before powering unit.
Ganging Jumper
Phase Block
Figure A:
Wire Pass-Through
For Desk to Desk Connecon
For Desk to Desk Connecons begin at step 1
For Desk to Storage with Spacer conguraons begin at step 4
For Desk to Storage without Spacer conguraons begin at step 7

Assembly Instrucon
Telephone [phone]
Fax [phone]
www.NationalOfficeFurniture.com
Part # 2891776
Rev, A
Printed in U.S.A
© 2014 Kimball International, Inc.
Alloy
Ganging Jumper
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call National Customer Service 800.482.1717.
4Verify that the powered beam and ganging kit are completely installed
and the units to be ganged together. Jumpers should be routed prior to
both storage cabinets being placed to allow access to grommet holes on
both sides. For Fixed Height ganging skip to step 6. For Adjustable Height
connue to step 5.
For Desk to Storage with Spacer Conguraons
Desk
Storage with Spacer
5
Run the jumper through spacer grommet hole and wire pass-through on
crosslink rail. Connect one end of the ganging jumper to the rst powered
beam phase block. Run the other end through opposite grommet hole and
wire pass-through. Connect the opposite end of the ganging jumper to the
rst phase block on the second unit. (Figure B)
Note: Verify all connecons have been fully seated and “clicked” into
proper posion before powering unit.
Grommet
Hole
Pass
Through
Jumper
(Not to Scale)
Figure B:

Assembly Instrucon
Telephone [phone]
Fax [phone]
www.NationalOfficeFurniture.com
Part # 2891776
Rev, A
Printed in U.S.A
© 2014 Kimball International, Inc.
Alloy
Ganging Jumper
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call National Customer Service 800.482.1717.
Connect one end of the ganging jumper to the rst powered beam open
phase block connecon. Run the jumper through the grommet holes in
the spacer. Connect the opposite end of the ganging jumper to the rst
open phase block connecon on the second unit. Figure C.
Note: Verify all connecons have been fully seated and “clicked” into
proper posion before powering unit.
6
Grommet Holes
Jumper
(Not to Scale)
Figure C:

Assembly Instrucon
Telephone [phone]
Fax [phone]
www.NationalOfficeFurniture.com
Part # 2891776
Rev, A
Printed in U.S.A
© 2014 Kimball International, Inc.
Alloy
Ganging Jumper
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call National Customer Service 800.482.1717.
For Desk to Storage Conguraons (No Spacer)
7Verify that the powered beam and ganging kit are completely installed
and the units to be ganged together. For Fixed Height ganging skip to step
9. For Adjustable Height connue to step 8.
Run the jumper through wire pass-through on crosslink rail. Connect one
end of the ganging jumper to the rst powered beam phase block. Run the
other end underneath storage and through opposite pass-through hole.
Connect the opposite end of the ganging jumper to the rst phase block on
the second unit. (Figure D & E)
Note: Storage Glides might need to be raised up to allow sucient
clearance for jumper conduit.
Note: Verify all connecons have been fully seated and “clicked” into
proper posion before powering unit.
8
Wire Pass-Through
Figure D:
Figure E:
Jumper Roung

Assembly Instrucon
Telephone [phone]
Fax [phone]
www.NationalOfficeFurniture.com
Part # 2891776
Rev, A
Printed in U.S.A
© 2014 Kimball International, Inc.
Alloy
Ganging Jumper
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call National Customer Service 800.482.1717.
Connect one end of the ganging jumper to the rst powered beam open
phase block connecon. Route the jumper underneath the storage. Con-
nect the opposite end of the ganging jumper to the rst open phase block
connecon on the second unit. Figure F.
Note: Storage Glides might need to be raised up to allow sucient
clearance for jumper conduit.
Note: Verify all connecons have been fully seated and “clicked” into
proper posion before powering unit.
9
Figure F:
Jumper Roung