National TESSERA HGT. ADJ. DESK User manual

Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call National Customer Service 800.482.1717.
Assembly Instrucon
Telephone [phone]
Fax [phone]
www.NationalOfficeFurniture.com
3206401
Rev, -
TESSERA HGT. ADJ.
DESK
Tools Required
-Screw Driver w/ #2 Phillips Bit
-Level
-Cable ties
Hardware
-Glides x8
Figure A
1
Unpack the desk and set into posion.
Figure B
Figure C
3
Install glides (Qty. 4 per shroud) supplied in hardware kit to underside of each
shroud (Figure C)
2
Remove two at brackets from the boom of each shroud to access the interior as
needed. Brackets can be discarded (Figure B) as they are only installed to protect
during shipping.
NOTE: Removable panel hangs from Z-clip brackets. Once at brackets are
removed care should be taken so that the panel does not disengage from Z-clip
and damage the component.

Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call National Customer Service 800.482.1717.
Assembly Instrucon
Telephone [phone]
Fax [phone]
www.NationalOfficeFurniture.com
3206401
Rev, -
TESSERA HGT. ADJ.
DESK
4
Posion desk in nal locaon and level the unit using the glides (Figure D).
Figure D
Figure E
6
The wire manager comes installed on the user’s right side shroud. If this is the
preferred locaon proceed to Step 7. If this isn't the preferred posion see the
Wire Manager Relocaon secon at the end of this instrucon to relocate it to the
le side shroud. Aer this relocaon procedure is complete proceed to Step 7.
5
The shroud’s interior panels can be removed to access the wire manger by pulling
up to clear the Z-clip then away to free the panel from the shroud (Figure E).
8
Replace removable panel back onto the shroud Z-clip hangers.
7
Run power and accessory lines through wire manager ensuring all leads run the full
length of the wire manager.
WARNING: Lines running to worksurface MUST be routed through the full length
of the wire manager to ensure enough lead length is available to support the
mechanism’s full range of moon.
9
Power up unit and review mechanism manual for recalibraon and usage.

Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call National Customer Service 800.482.1717.
Assembly Instrucon
Telephone [phone]
Fax [phone]
www.NationalOfficeFurniture.com
3206401
Rev, -
TESSERA HGT. ADJ.
DESK
Figure F
2A
Remove four screws securing wire manager. There are two aached to the
underside of the worksurface and two on the underside of the shroud top
(Figure G).
Figure G
Wire Manager Relocaon
1A
Ensure the height adjustable mechanism is unplugged before moving on.
If not done so already remove the access panel on both shrouds. Remove all
wires back through the wire manager so that its empty (Figure F).

Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call National Customer Service 800.482.1717.
Assembly Instrucon
Telephone [phone]
Fax [phone]
www.NationalOfficeFurniture.com
3206401
Rev, -
TESSERA HGT. ADJ.
DESK
Figure H
3A
On the opposite side shroud remove the grommet cap (Figure H) installed in
the top of the shroud. This cap is retained by tabs on both sides of the cap
(Figure I). Depress these tabs in and push out to remove cap from the grommet
(Figure J). Re-install this cap on the shroud without the wire manager to close
o the grommet hole.
Figure I
4A
Reusing the removed hardware install the wire manager in the new locaon in
the same manner as it was installed originally (Figure K).
Figure J
Figure K

Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call National Customer Service 800.482.1717.
Assembly Instrucon
Telephone [phone]
Fax [phone]
www.NationalOfficeFurniture.com
3206401
Rev, -
TESSERA HGT. ADJ.
DESK
Figure M
Figure L
5A
(For L Unit Installaon)
Return to Tessera Return Install AI Step 9
(For Desk Unit Only Installaon)
The control box and power supply will need to be shied to the opposite side
to allow for the power supply cord to run down the reposioned wire
manager. Remove fasteners, re-posion, and reinstall power supply bracket,
control box, and handset to underside of worksurface reusing original
fasteners. See right mount (Figure L) and le mount (Figure M) layouts below
for reference. Posions are approximate.
6A
Reconnect mechanism cables to control box.
7A
Return to Step 7