National Alloy User manual

Assembly Instrucon
Telephone [phone]
Fax [phone]
www.NationalOfficeFurniture.com
Part # 3112080
Rev, A
Printed in U.S.A
© 2018 Kimball International, Inc.
Alloy
Ceiling Power/Data Pole
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call National Customer Service 800.482.1717.
Figure A:
Package Contents
1Lay out pieces on the ground and locate mounng hardware supplied.
(Figure A)
Item Qty
#10-32 X 3/16
Socket Head Capscrew 4
#8 X 1/4” Screw
Phillips 4
#10 X 1/2” Hex Head
Self Tapping Screw 2
Component
Power Pole
Tools Required
Screw Driver #2 Phillips
1/4” Socket
2Install main mounng bracket to the pole casing with four (4)
#10-32 x 3/16” capscrews. (Figure B)
Figure B:

Assembly Instrucon
Telephone [phone]
Fax [phone]
www.NationalOfficeFurniture.com
Part # 3112080
Rev, A
Printed in U.S.A
© 2018 Kimball International, Inc.
Alloy
Ceiling Power/Data Pole
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call National Customer Service 800.482.1717.
3Install pole wire divider into main pole casing. There are 3 posions the
wire divider can be installed in, select a posion based on the needs of
the applicaon. Ensure the divider is fully seated onto mounng prole.
(Figure C)
Note: If the middle prole is used for the wire divider the piece
needs to be oset from the end of the case by 3” min. to allow
for clearance for the glide mounng screw when installed.
(Figure D)
Figure C:
Figure D:
Offset for center position
only

Assembly Instrucon
Telephone [phone]
Fax [phone]
www.NationalOfficeFurniture.com
Part # 3112080
Rev, A
Printed in U.S.A
© 2018 Kimball International, Inc.
Alloy
Ceiling Power/Data Pole
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call National Customer Service 800.482.1717.
4Install face plate along full length of casing. Ensure all three locang
proles are seated along full length of casing. (Figure E)
Figure E:

Assembly Instrucon
Telephone [phone]
Fax [phone]
www.NationalOfficeFurniture.com
Part # 3112080
Rev, A
Printed in U.S.A
© 2018 Kimball International, Inc.
Alloy
Ceiling Power/Data Pole
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call National Customer Service 800.482.1717.
5Install boom glide mount to case using four (4) #8 X 1/4” screws.
(Figure F)
Figure F:
6Install boom glide into threaded hole in glide mount plate
(Figure G)
Figure G:

Assembly Instrucon
Telephone [phone]
Fax [phone]
www.NationalOfficeFurniture.com
Part # 3112080
Rev, A
Printed in U.S.A
© 2018 Kimball International, Inc.
Alloy
Ceiling Power/Data Pole
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call National Customer Service 800.482.1717.
7Stand up nished pole assembly and mount to nish assembled table
using two (2) #10 X 1/2” self tapping screws.
If mounng to Adjustable Height Table mount to underside of power
bar. (Figure H)
Figure H:
If mounng to Fixed Height Table mount to underside of leg with
bracket ush against rear leg. (Figure I)
Figure I:

Assembly Instrucon
Telephone [phone]
Fax [phone]
www.NationalOfficeFurniture.com
Part # 3112080
Rev, A
Printed in U.S.A
© 2018 Kimball International, Inc.
Alloy
Ceiling Power/Data Pole
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call National Customer Service 800.482.1717.
9(Oponal for trim plate installaon)
Bend arms out and slide trim plate over top of power pole assembly.
Posion underneath ceiling cutout. (Figure J)
Figure J:
8Secure upper end of power pole assembly to xed support in ceiling.
Various methods are acceptable using hanger strapping or other
construcon materials so long as a rigid support is created.