National Alloy User manual

Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call National Customer Service 800.482.1717.
Assembly Instrucon
Telephone [phone]
Fax [phone]
www.NationalOfficeFurniture.com
Part # 2951091
Rev, A
Printed in U.S.A
© 2014 Kimball International, Inc.
Package Contents
Alloy
Fixed Height Double
Bases
Hardware Qty
M6 x 12 8
Handle 4
Lock Plate 4
Mounting Bracket 4
Woodscrews 8
Tools Required
4mm Allen Wrench
Screw Driver
#2 Phillips Bit
Note: This assembly instrucon will cover all conguraons of Alloy xed
height double bases.
1Assemble the two adjustable upper channels as shown in Figure A. Using
the supplied handle and lock plate roughly set the length of the adjustable
channel to the desired surface size and conguraon ordered in Figure B.
Repeat Step 1 for the second adjustable upper channel supplied.
Figure B:
Surface Size Freestanding: Start: Mid: End:
48 39 1/2” 42” 44 1/2” 42”
54 45 1/2” 48” 50 1/2” 48”
60 51 1/2” 54” 56 1/2” 54”
66 57 1/2” 60” 62 1/2” 60”
72 63 1/2” 66” 68 1/2” 66”
Figure A:
2Using the tabs as shown in Figure C, aach one side of the adjustable
upper channel to the rst end leg.
Figure C:

Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call National Customer Service 800.482.1717.
Assembly Instrucon
Telephone [phone]
Fax [phone]
www.NationalOfficeFurniture.com
Part # 2951091
Rev, A
Printed in U.S.A
© 2014 Kimball International, Inc.
Package Contents
Alloy
Fixed Height Double
Bases
Hardware Qty
M6 x 12 8
Handle 4
Lock Plate 4
Mounting Bracket 4
Woodscrews 8
Tools Required
4mm Allen Wrench
Screw Driver
#2 Phillips Bit
3Verify the upper channel is fully seated as shown in Figure D. Using the
mounng bracket and M6 x 12 screws provided, secure the adjustable
upper channel to the end leg as shown in Figure E.
4Repeat steps 2-3 for all remaining adjustable upper channels and connec-
on points. Once complete, the enre frame should be constructed to
your desired conguraon.
Figure D:
Figure E:

Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call National Customer Service 800.482.1717.
Assembly Instrucon
Telephone [phone]
Fax [phone]
www.NationalOfficeFurniture.com
Part # 2951091
Rev, A
Printed in U.S.A
© 2014 Kimball International, Inc.
Package Contents
Alloy
Fixed Height Double
Bases
Hardware Qty
M6 x 12 8
Handle 4
Lock Plate 4
Mounting Bracket 4
Woodscrews 8
Tools Required
4mm Allen Wrench
Screw Driver
#2 Phillips Bit
Place the center beam onto the frame beam mount brackets as shown in
Figure F. Set the distance from the end of the beam to the outside end leg
as shown in Figure G. (powered and non-powered beam are installed in
the same method)
5
Figure F:
40 mm
Figure G:
From the boom of the beam align the two outside v grooves with the
holes in the beam mounng brackets as shown in Figure H. Using the
provided self-drilling screws, secure the beam to beam mounng brack-
ets on one end. It is recommended to use a clamp and pads when fas-
tening the beam to help prevent misalignment.
Figure H:
6
Note: When mounng beams addional beams to a Mid or End unit, lo-
cate addional beams ush against the rst beam mounted on the Start
unit.

Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call National Customer Service 800.482.1717.
Assembly Instrucon
Telephone [phone]
Fax [phone]
www.NationalOfficeFurniture.com
Part # 2951091
Rev, A
Printed in U.S.A
© 2014 Kimball International, Inc.
Package Contents
Alloy
Fixed Height Double
Bases
Hardware Qty
M6 x 12 8
Handle 4
Lock Plate 4
Mounting Bracket 4
Woodscrews 8
Tools Required
4mm Allen Wrench
Screw Driver
#2 Phillips Bit
Note: When securing surfaces verify that all worksurfaces are ght with
no gaps between the center beam or any other ganged surfaces before
fully securing.
9Repeat steps 5—8 for all remaining units in the run. Once all surfaces
are secured. Fully ghten down the handle and lock plates from Step
1 on all adjustable upper channels.
7
Aach the worksurfaces to the frame using the provided woodscrews.
The surface should be ush with the end of the center beam and ght
against it in the center. Secure each worksurface by placing one screw
through each side of the mounng plate as shown in Figure K.
Figure K:
8
Pull the adjustable upper channels / frame into nal posion. Secure
the remaining end of the center beam. When aaching to an end leg
use the dimensions shown in Figure G. When aaching to a mid leg,
center the end of the beam in the center of the mid leg as shown in
Figure J.
Figure J: