National LOCHLYN User manual

Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call National Customer Service 800.482.1717.
Assembly Instrucon
Telephone [phone]
Fax [phone]
www.NationalOfficeFurniture.com
3249051,-
Rev, -
LOCHLYN MODULE
PASS THRU
TOOLS REQUIRED
DRILL DRIVER W/ PHILLIPS BIT
HARDWARE
#8X5/8” PAN HEAD SCREWS
QTY X4
#8X1 1/8” FLAT HEAD SCREWS
QTY X4
1
THIS MODULE IS ASSEMBLED WITH A HIDDEN
FASTENER HARDWARE SYSTEM THAT COMES
PREINSTALLED. ONE OF THESE, THE CHANNEL LOCK
FASTENER, IS THE FEATURED IN THIS ASSEMBLY
(FIGURE A). IF PANELS APPEAR TO BE MISSING
FASTENERS OR THEY ARE DAMAGED, CONTACT
CUSTOMER SERVICE FOR REPLACEMENTS.
FIGURE A
2
RETREIEVE END PANEL AND STAND IT UP SO THAT THE
FRONT EDGE IS ON THE GROUND AND THE THRU HOLES
IN THE CORNERS ARE ON TOP (FIGURE B). NOTE THE ROUTED
PROFILES (FIGURE C) ON THE END PANEL AND THE
DIRECTION OF THE SMALLER ROUT COMPARED TO THE
CLEARANCE SLOT. THE SMALLER ROUT IS THE CAPTURE
PROFILE THAT WILL HOLD AND POSITION THE CHANNEL
LOCK.
FIGURE B
FIGURE C
FIGURE D
3
RETREIVE THE TOP PANEL, THAT HAS TWO SETS OF PILOT HOLES, AND START THE
PANEL INTO THE FIRST SET OF ROUTED PROFILES (FIGURE D). SLIDE OVER TO LOCK
IT INTO THE END PANEL (FIGURE E).
NOTE: END PANEL ROUTED CUTS ARE SYMMETRIC AND DOESN’T HAVE A SET TOP OR
BOTTOM TO INSTALL THE TOP PANEL. USE GRAIN DIRECTION OF THE PANEL TO
DETERMINE WHICH SIDE SHOULD BE THE TOP.
NOTE: ENSURE TOP PANEL PILOT HOLES ARE FACING OUT AWAY FROM THE INTERIOR OF
THE BOX, NOT TOWARDS THE INSIDE. CORRECT IF NECESSARY AT THIS POINT.
FIGURE E

Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call National Customer Service 800.482.1717.
Assembly Instrucon
Telephone [phone]
Fax [phone]
www.NationalOfficeFurniture.com
3249051,-
Rev, -
LOCHLYN MODULE
PASS THRU
4
RETRIEVE BOTTOM PANEL AND ENGAGE INTO THE REMAINING ROUTED PROFILES
(FIGURE F). PRESS DOWN TO LOCK IT INTO POSITION (FIGURE G).
FIGURE F FIGURE G
5
RETREIVE THE LAST END PANEL AND LOCK IT ONTO THE REMAINING CHANNEL
LOCKS (FIGURE H). TO VERIFY CORRECT ASSEMBLY THE COUNTERSUNK PILOT HOLES
SHOULD BE ON THE SAME SIDE AS THE OTHER END PANEL (FIGURE I).
FIGURE H
FIGURE I
6
AT EACH COUNTER SUNK HOLE (4X) START AND RUNDOWN A #8 X 1 1/8” FLAT
HEAD SCREW FROM THE HARDWARE KIT, INTO THE TOP AND BOTTOM PANEL. THIS
LOCKS UP THE UNIT (FIGURE J). PASS THRU
ASSEMBLY IS COMPLETE AT THIS POINT.
NOTE: TAKE EXTRA CAUTION IN THE HANDLING OF
THE PASS THRU MODULE. IT IS EASY TO RACK AND
DAMAGE THE UNIT UNTIL IT IS INSTALLED IN THE
FRAME.
FIGURE J

Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call National Customer Service 800.482.1717.
Assembly Instrucon
Telephone [phone]
Fax [phone]
www.NationalOfficeFurniture.com
3249051,-
Rev, -
LOCHLYN MODULE
PASS THRU
7
INSTALL BOX INTO FRAME ENSURING TOP PANEL
WITH PILOT HOLES ARE FACING UP (FIGURE K).
FIGURE K
8
RETRIEVE THE TWO HANGER BRACKETS FROM THE HARDWARE KIT. THEY MOUNT IN
THE CENTER OF THE PASS THRU ON BOTH SIDES. POSITION THEM SO THE FOLDED
HOOK GRABS ONTO THE LIP OF THE HORIZONTAL FRAME MEMBER AND THE MOUNTING
HOLES CENTER UP WITH THE PILOT HOLES IN THE TOP PANEL (FIGURE L). START AND
RUN DOWN THE INCLUDED 5/8 PAN HEAD SCREWS TO INSTALL THE PASS THRU TO THE
FRAME (FIGURE M).
FIGURE L
FIGURE M
9
PLACE INCLUDED COVER PANEL IN THE MODULE ABOVE TO COVER OVER THE
BRACKETS (FIGURE N). INSTALLATION IS COMPLETE AFTER THIS (FIGURE O).
FIGURE N
FIGURE O