Nautilus Hyosung MX7600I User manual

Operator Manual
MONiMAX7600I System
V01.00.00 (2017.05.16)
© Nautilus Hyosung, Inc. All Rights Reserved.

© Nautilus Hyosung, Inc. All Rights Reserved. I
Revision History
Operator Manual - MX7600I System
No.
Version
Date
Description of Change
Chapter
1
V01.00.00
2017/05/16
New Publication
All
© Nautilus Hyosung All Rights Reserved.
The content of this specification is protected by copyright laws.
2017.05. 16. 1st Release

II © Nautilus Hyosung, Inc. All Rights Reserved.
Contents
Chapter1. Preface...........................................................................................................................1-1
Purpose ........................................................................................................................................................1-1
Audience.......................................................................................................................................................1-1
Support Information......................................................................................................................................1-1
What is in This Manual.................................................................................................................................1-1
Terminologies ...............................................................................................................................................1-2
Abbreviations................................................................................................................................................1-2
Safety Precautions (English)........................................................................................................................1-4
Précautions pour la sécurité (French)..........................................................................................................1-6
Related Document ........................................................................................................................................1-8
Chapter2. Introduction...................................................................................................................2-1
About the MX7600I.......................................................................................................................................2-1
The Exterior Overview..................................................................................................................................2-2
Basic Features..............................................................................................................................................2-3
Devices of MX7600I .....................................................................................................................................2-6
CE (Control Electronics, PC)······························································································2-6
Customer Display & Keypad·······························································································2-7
Cash Dispenser Unit ········································································································2-8
Card Reader···················································································································2-9
Receipt Printer·············································································································· 2-10
Cash & Check Inert Module (CCIM)··················································································· 2-11
Power Supply ··············································································································· 2-12
Heater························································································································· 2-13
Safety & Security··········································································································· 2-14
Chapter3. For the beginning operator...........................................................................................3-1
Opening the Exterior Door............................................................................................................................3-1
Closing Upper & Lower Front Body..............................................................................................................3-2
Opening the Security Enclosure...................................................................................................................3-3
Switching Power On/Off ...............................................................................................................................3-4
Switching Power On·········································································································3-4
Switching Power Off·········································································································3-4
Power Supply Status ········································································································3-4
Locking Devices ...........................................................................................................................................3-5
Cencon Lock ··················································································································3-5
Electronic Lock·············································································································· 3-10
Environment ...............................................................................................................................................3-12
General Guidelines to Environmental Exposure···································································· 3-12
Chapter4. Cash & Check Insert Module (CCIM)............................................................................4-1
Basic Specification of Cash & Check In Module ..........................................................................................4-3
Specification of External Appearance ..........................................................................................................4-4
Cash & Check Conditions ............................................................................................................................4-5
How to remove jam from each section.........................................................................................................4-6
Remove jam from Bundle Module························································································4-8
Remove jam from the First Transport Path ············································································4-9
Remove jam from BC ····································································································· 4-10
Remove jam from ALG···································································································· 4-11
Remove jam from Recog Transport Section········································································· 4-12
Remove jam from the B2 Upper Transport Path of BM2 ························································· 4-13
Remove jam from the B2 Upper Transport Path of BM2 ························································· 4-14
Remove jam from B2 Reject Transport Section ···································································· 4-15
Remove jam from B3 Transport Section·············································································· 4-16
Remove jam from Reject Section ······················································································ 4-17

© Nautilus Hyosung, Inc. All Rights Reserved. III
Remove jam from B3 Escrow Transport Section····································································4-18
Remove jam from B4 Transport Section ··············································································4-19
Remove jam from Escrow ································································································4-20
Remove jam from RT/A6 Cassette ·····················································································4-21
Remove jam from Cassette ······························································································4-23
How to change PRT Maintenance Module.................................................................................................4-25
How to replace Ink cartridge ·····························································································4-25
How to reset PRT Cartridge Count ·····················································································4-26
How to replace Ink Head Cleaner Felt·················································································4-28
Chapter5. Cash Dispenser.............................................................................................................5-1
Bill Conditions...............................................................................................................................................5-1
Acceptable condition········································································································ 5-1
Unacceptable condition····································································································· 5-2
How to Replenish the Cash Cassette...........................................................................................................5-6
How to Empty the Reject/Retract Box........................................................................................................5-10
How to Clear Jamming in cash dispenser..................................................................................................5-13
Remove jam from the upper horizontal transport path·····························································5-14
Remove jam from the vertical transport path·········································································5-16
Remove jam from the carriage ··························································································5-17
Remove jam from the transport path of the main body····························································5-18
Remove jam from the transport path of RJ/RT box·································································5-19
Remove jam from the separation part ·················································································5-20
Remove jam from the transport path of reject ·······································································5-21
How to Reset Main Board...........................................................................................................................5-22
How to set the Cassette for Each Denomination .......................................................................................5-23
Cassette Base Guide Setting for the Horizontal Size of Each Denomination ································5-23
Cassette Cover Guide Setting for the Vertical Size of Each Denomination ··································5-27
Change Note Index·········································································································5-29
Chapter6. Receipt Printer...............................................................................................................6-1
Receipt Paper...............................................................................................................................................6-1
How to load the receipt paper.......................................................................................................................6-2
How to clear jamming in receipt printer........................................................................................................6-4
Memo.......................................................................................................................................Memo-1

Operator Manual Chapter1. Preface
© Nautilus Hyosung, Inc. All Rights Reserved. 1-1
Chapter1. Preface
Purpose
▶This manual is produced to describe how the customers operate Nautilus Hyosung’s
MX7600I.
This manual details how the customers replenish the notes and paper and how they
remove the jam at the MX7600I.
Audience
▶Customers and staffs of Nautilus Hyosung who use and operate the MX7600I in each
branches of bank.
Support Information
▶If any question or error occurs while operating MX7600I in compliance with this manual,
please contact maintenance staffs of Nautilus Hyosung.
For the contact of maintenance staffs of Nautilus Hyosung, see the E-mail addresses
and telephone numbers provided separately.
What is in This Manual
▶MONiMAX referred to as “MX”
▶This manual is designed to provide the operation guide for the MX7600I and the
detailed description of the following:
▪Replenishing the notes and the receipt paper
▪Emptying the notes and the checks
▪Removing the jam like the notes, the checks and the receipt paper
▶All information described in this manual is a licensed product of Nautilus Hyosung.
Some of the information in this manual may differ according to the network processor to
be connected and may be subsequently updated by the bank’s needs or the improvement
by Nautilus Hyosung.
It is the policy of Nautilus Hyosung to improve products as new technology, components,
software, and firmware become available. Therefore Nautilus Hyosung reserves the right
to change specifications without notice.

Chapter1. Preface Operator Manual
1-2 © Nautilus Hyosung, Inc. All Rights Reserved.
Terminologies
▶In this document the terminology listed below is used as follows:
▪Customer and consumer refer to any person who transacts business through the
ATM.
▪Device and unit refer to the standard and optional ATM equipment, such as monitor,
card reader, printer and dispenser.
▪Fascia refers to the entire front portion of the unit, including the portion where the
customer transacts business.
▪Module refers to a plug-in device that can be serviced or replaced.
▪Note(s) and bill(s) refer to the individual documents loaded into and dispensed from
the dispenser.
▪Servicing and maintenance refer to the supervisor, operator and technician’s tasks
performed to keep the ATM operational.
▪Screen refers to the text appearing on the customer display.
Abbreviations
▶In this document the abbreviations listed below is used as follows:
#
Abbreviations
Description
1
AD board
Analog to Digital conversion board
2
ADA
The American Disabilities Act
3
ALG
Alignment Module
4
AP
Application Program
5
Assy
Assembly
6
BATT S/W
Battery Switch
7
BC
Bill Checker
8
BM1
Body Module1
9
BM2
Body Module2
10
BM3
Body Module3
11
BUNDLE
Bulk Note Separation Module
12
CAM
Camera Unit
13
CASSETTE
Cash & Check Cassette
14
CCIM
Cash & Check In Module
15
CCR
Contactless Card Reader
16
CDU
Cash Dispenser Unit
17
CE
Control Electronics
18
Earphone Jack
Voice Converter for Visually Disabled Persons (ADA)
19
EMV
Europay, Mastercard, Visa

Operator Manual Chapter1. Preface
© Nautilus Hyosung, Inc. All Rights Reserved. 1-3
#
Abbreviations
Description
20
EP
Elementary Program
21
EPP
Encryption PIN Pad
22
Escrow
Escrow Module
23
FELT
Ink Head Cleaner Felt
24
H/W
Hardware
25
I/F
Interface
26
ISO
International Standard Organization
27
JPR
Journal Printer
28
LCD
Liquid Crystal Display
29
MCU
Magnetic Card Unit
30
OPL
Operation Panel for Customers to Operate
31
OSD board
On Screen Display Board
32
P/S
Power Supply
33
PIN
Personal Identification Number
34
PNC
Panel Control Board
35
PRT
Endorsement Module
36
PTR
Printer (mainly Receipt Printer)
37
RECOG
Recognition Module
38
REJECT
Reject Module
39
RT/A6
Retract & A6 Cassette
40
S/W
Switch
41
SCM
Separator Control Module
42
SIU
Sensor and Indications Unit
43
SP
Service Provider
44
SPR
Slip Printer (Receipt Printer)
45
TTU
Text Terminal Unit (OPL or SPL)
46
VFD
Vacuum Fluorescent Display

Chapter1. Preface Operator Manual
1-4 © Nautilus Hyosung, Inc. All Rights Reserved.
Safety Precautions (English)
▶Common Safety Precaution
Precautions outlined this manual provide information on safe
and proper handling of the product. Non-compliance of the
precautions may result in injury or damage to the product.
This precaution symbol with sample term tells you safety
warnings during equipment handlings.
▶Please read the following instructions before operating equipment.
▪Operate equipment in the order outlined in this manual.
▪Follow precautions indicated in this manual, as well as the equipment itself.
Failure to properly address these precautions may lead to injury or damage to the
product.
▪Avoid operations not addressed in this manual.
▪If you cannot remedy system problems using the methods outlined in this manual,
please refer to contact information listed in the manual.
▪Any change or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
<Note!>
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.
▶Description of Precaution Symbols
Symbol
Description
Electrical Shock Warning
▪Do not remove cover. Only a maintenance engineer is
allowed to open the cover.
▪Do not touch. You may receive electric shock.
▪Make sure to turn off the power when servicing the
equipment.
High Temperature Warning
▪Do not touch the equipment when it is running.
▪The equipment can get extremely hot and may cause a
burn.
▪Make sure to close the cover before running the
equipment.

Operator Manual Chapter1. Preface
© Nautilus Hyosung, Inc. All Rights Reserved. 1-5
Use Precaution when Moving
▪The equipment is heavy. Make sure at least 2 people lift or
move the equipment.
▪Do not attempt to move the equipment alone. You may be
injured from dropping the heavy equipment.
Fire Hazard
▪Place the equipment in an area away from any
combustible materials.
▪The equipment may catch on fire from overheating or short
circuit of the power supply unit.
Disassembly Warnings
▪Do not disassemble or modify the equipment unless you
are a certified engineer.
▪Contact the service center for maintenance, adjustments
and repairs.
▪Improper disassembly may cause fire or electrical shock.
Collapse Precautions
▪Do not place the equipment where the floor cannot sustain
the weight of the equipment, or on slanted or unstable
surface.
▪Equipment may fall and cause injury or damage.
Unplug the Equipment
▪Stop using the equipment immediately if it smokes, emits
an unusual smell, makes abnormal sounds, or if liquids or
other foreign materials enter the equipment.
▪If the above-mentioned abnormalities occur, immediately
turn off the power, unplug the equipment and contact the
service center.
▪If you ignore these symptoms, the equipment may catch on
fire or cause electric shock.
<CAUTION>
1. TO REDUCE THE RISK OF FIRE, USE ONLY No. 26 AWG OR LARGER
TELECOMMUNICATION LINE CORD
2. RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT
TYPE. DISPOSED OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
3. FOR PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED
NEAR THE EQUIPMENT AN SHALL BE EASILY ACCESSIBLE
4. THE EQUIPMENT IS TO BE SECURED TO THE BUILDING STRUCTURE BEFORE
OPERATION

Chapter1. Preface Operator Manual
1-6 © Nautilus Hyosung, Inc. All Rights Reserved.
Précautions pour la sécurité (French)
►Précaution générale pour la sécurité
Précautions décrits de ce manuel fournissent des informations
sur une manipulation sûre et appropriée du produit. Le non-
respect des précautions peut causer des blessures ou
endommager le produit.
Ce symbole de précaution avec le terme d’example vous
indique des consignes de sécurité lors de la manipulation de
l'équipement.
►Veuillez lire des instructions suivantes avant d'utiliser l'équipement
▪Fonctionner l'équipement dans l'ordre indiqué dans ce manuel.
▪Suivre les précautions indiquées dans ce manuel, ainsi que l'équipement lui-même.
Le défaut de traiter correctement de ces précautions peut entraîner des blessures ou
endommager le produit.
▪Évitez des opérations non traitées dans ce manuel.
▪Si vous ne pouvez pas résoudre des problèmes du système en utilisant des méthodes
décrites dans ce manuel, veuillez se référer aux informations de contact figurant dans
le manuel, s’il vous plaît.
▪Certain changement ou des modifications dans la construction de ce dispositif qui ne
sont pas expressément approuvés par la partie responsable de la conformité
pourraient annuler l'autorité de l'utilisateur de faire fonctionner l'équipement.
<REMAQUE!>
Cet équipement a été testé et fondé pour se conformer aux limites pour un équipement
numérique de classe A, conformément à la partie 15 des règles FCC. Ces limites sont
conçues pour fournir une protection raisonnable contre des interférences nuisibles
lorsque l'équipement est utilisé dans un environnement commercial. Cet équipement
génère, utilise et peut émettre des fréquences radios et, s'il n'est pas installé et utilisé
conformément aux instructions de ce manuel, peut causer des interférences nuisibles
aux communications radios.
Le fonctionnement de cet équipement dans une zone résidentielle est susceptible de
provoquer des interférences nuisibles dans le cas, l'utilisateur devra corriger ces
interférences à ses propres frais.
►Description des symboles de précaution
Symbole
Description
Choc électrique
• Ne pas retirer le couvercle. Seul le technicien d'entretien est
autorisé à ouvrir
le couvercle.
• Ne pas toucher. Vous pouvez avoir un choc électrique.
• Assurez-vous d'éteindre l'appareil lors de l'entretien de
l'équipement.

Operator Manual Chapter1. Preface
© Nautilus Hyosung, Inc. All Rights Reserved. 1-7
À haute temperature
• Ne pas toucher l’équipement quand il est en marche.
• L’équipement peut devenir extrêmement chaud et peut
provoquer une brûlure.
• Assurez-vous de fermer le couvercle avant de lancer
l'équipement.
Soyez prudent lors du déplacement
• L'équipement est lourd. Assurez-vous d'au moins 2
personnes pour soulever ou déplacer l'équipement
• N'essayez pas de déplacer l’équipement seul. Vous pouvez
être blessés par la chute de l'équipement lourd.
Risque d'incendie
• Placer l’équipement dans une zone éloignée de tous les
matériaux combustibles.
• L'équipement peut s'enflammer de surchauffe ou de court-
circuit de l'unité d'alimentation.
Démontage
• Ne pas démonter ou de modifier l'équipement, sauf si vous
êtes ingénieur certifié.
• Contacter le centre de service pour l'entretien, le réglage et
la réparation.
• Le mauvais démontage peut provoquer un incendie ou un
choc électrique.
Tomber
• Ne pas placer l'équipement dont le sol ne peut pas
supporter le poids de l'équipement, ou sur une surface
inclinée ou instable.
• L'équipement peut tomber et provoquer des blessures ou
des dommages.
Débrancher l'équipement
• Cessez d'utiliser l’équipement immédiatement si il fume,
émet une odeur inhabituelle, fait des bruits anormaux ou si
des liquides ou d'autres matériaux étrangers dans
l'équipement.
• Si les anomalies mentionnées ci-dessus se produisent,
éteignez immédiatement la puissance, débranchez
l'appareil et contactez le centre de service.
• Si vous ignorez ces symptômes, l’équipement peut prendre
feu ou provoquer un choc électrique.
AVERTISSEMENT :
1. POUR RÉDUIRE LES RISQUES D'INCENDIE, UTILISEZ UNIQUEMENT AWG n °26 OU
LA LIGNES DE TELECOMMUNICATION PLUS GROSSE
2. RISQUE D'EXPLOSION SI LA BATTERIE EST REMPLACEE PAR UN TYPE
INCORRECT. DISPOSER POUR UTILISATION DES BATTRIES SELON LES
INSTRUCTIONS
3. POUR LES APPAREILS RACCORDES, LA PRISE DOIT ETRE INSTALLEE PRES
D’EQUIPEMENT POUR ÊTRE FACILEMENT ACCESSIBLE

Chapter1. Preface Operator Manual
1-8 © Nautilus Hyosung, Inc. All Rights Reserved.
4. L’EQUIPEMENT DOIT ETRE SECURISE A LA STRUCTURE DU BATIMENT AVANT
D'UTILISER
Related Document
►The related documents are listed as follows. If needed, please contact staffs of our
technical support team and maintenance team.
▪Installation Manual
▪Service Manual
▪VDM Manual (Diagnostic)
▪Error Code Manual
For the contact of maintenance staffs of Nautilus Hyosung, see the E-mail addresses
and telephone numbers provided separately.

Operator Manual Chapter2. Introduction
© Nautilus Hyosung, Inc. All Rights Reserved. 2-1
Chapter2. Introduction
About the MX7600I
►The MX7600I is a full service ATM. Consumers deposit the cash/check, make the
withdrawal and receive the transaction records through openings in the fascia with
MX7600I ATM.
The MX7600I is a versatile, easily maintained delivery system that can be modified to
keep pace with the bank's changing needs.
The island ATM requires no protective shelter in order to function. However, for the
convenience of consumers and maintenance personnel, some form of enclosure is
recommended. Whenever the ATM is opened for servicing, the electronics must be
protected from exposure to rain or snow. You replenish supplies and service the
Island ATM from the front of the unit.
►The benefits that the new concept MX7600I provides are as follows.
Removes inconvenience which occurs when bank clerks directly handle cash and
checks with customers and relieves workload upon tellers by processing deposit/
withdrawal of cash/check automatically.
Relieves risks and burden of directly handling cash/check by directly keeping cash/
check deposited in a safe.
Allows tellers to calculate and close amount on hand faster than the existing manual
calculation.
Abank customer and a teller can easily interact on a touch screen, just like talking,
through Nautilus Hyosung’s intuitive and easy UI.
Allows easy and quick installation and maintenance.
.

Chapter2. Introduction Operator Manual
2-2 © Nautilus Hyosung, Inc. All Rights Reserved.
The Exterior Overview
►The following picture shows the front of MX7600I and key units.
The fascia provides the interface between the customer and MX7600I.
The customer selects transactions and requests information at the fascia.
Receipt
Printer Slot
Earphone
Jack
Card
Reader Slot
Customer
Display with
Touch
Screen
(Function
Key,
optional)
Cash
Dispenser
Slot
Encryption
PIN Pad
Deposit
Statement Printer Slot (Optional)
Car
Detection
Sensor
Front Door key

Operator Manual Chapter2. Introduction
© Nautilus Hyosung, Inc. All Rights Reserved. 2-3
Basic Features
▶Important features of the MX7600I is highlighted in the following list:
<Note!>
1. Your MX7600I may not contain all the devices described in this section. Some devices are optional
and some devices cannot be used in combination with other devices (mutually exclusive
combinations).
2. Option :
Item
Specification
Remarks (Option)
Main
Controller
(H81)
CPU
G3420 3.2 GHz
Memory
DDR
Memory
4 GB
DDR-II
Storage
Device
HDD
500 GB
SATATYPE
ODD
DVD-RW
SATATYPE
Operating System
Windows 7 Pro Embedded
with Service Pack 3 (Eng)
Expansion Slots
2*PCI, 1*PCI-Express x16,
1*PCI-Express x1
H81 Main B/D
Serial Ports
1 Ports
USB Ports
14 Ports
Main Board 8 Ports(USB 3.0
2EA),
USB 2.0 Hub 7Ports
Main Board USB 2.0
Setting
USB Extension Card
4 Ports (USB 2.0 PCI Card)
LAN
10/100/1000Mbps On-Board
Status Display LED
HDD / PWR LED
Customer
Display
Display
Type
15” TFT LCD
Brightness
1,500 cd/m²(SunLight
Viewable)
Motorized
Tilting
Mechanism
LCD Angle Tilting by 3
buttons & Car detection
sensor
Height (Sedan / SUV / VAN)
Privacy Filter
15” Filter
Guide Light
Flicker
White : SPR/CDU/EDU/MCU
Printer/BNA Flicker Option
Open
/Close
Status Display Light
(Red/Green)
Status Display Light
(Red/Green)
Support Auto-Dimming
Night –dim/ Day-bright
Customer
Input Method
Pin-Pad
EPP3.0 TR39
Function Key
Touch Screen
Function Key Option
Supervisor
Operation
Display Module
10.1” TFT LCD, 250cd/m2
Input Method
Touch Screen
Cash
Dispenser
Sutter type
Automatic Shutter
Denomination
US $20(ID 1,1,1,1)

Chapter2. Introduction Operator Manual
2-4 © Nautilus Hyosung, Inc. All Rights Reserved.
Item
Specification
Remarks (Option)
(H-CDU)
Maximum Dispense
50 Notes/1 transaction
Number of cassettes
4 Cassettes
Cassette Capacity
3,000 notes/1 cassette
Reject Type
Note by Note Reject (200
bills Max)
Retract
Bundle Retract (200 bills
Max)
Card Reader
(Sankyo-DIP)
Type
EMV Support DIP Type
Motor Option
Magnetic Stripe
ISO 1,2 Read
IC card Support
Support
Bezel Color
Translucent Blue Bezel
Receipt
Printer
(K-SPR11)
Printing Type
Thermal Line Printing
K-SPR5E Option
Printing Width
80mm Max
Paper
Specification
Type
Thermal Roll Paper
Width
Max. 80mm
Outer
Diameter
Max. 210Φ
Paper Roll Capacity
5,000 Transaction/Roll
Depends on Format
Black Mark Paper Support
None
Black Mark Paper Option
Cash &
Check
In Module
(CCIM)
Media Size
Width
Min : 60 mm (2.36 inch)
Max : 102 mm (4.01 inch)
Length
Min : 110 mm (4.33 inch)
Max : 230 mm (9.055 inch)
Thickness
Min : 0.075 mm (0.0029 inch)
Max : 0.2 mm (0.0078 inch)
Bundle Capacity
50 Mixed Notes and Checks
/1 transaction
One Single Deposit Slot
Deposit Direction
4 way
Capacity
Deposit
Cassettes
2,000 notes/1 cassette
2,000 checks/1 cassette
Criteria for Deposit New
Notes & Checks
Reject
Cassettes
50 Mixed Notes and Checks
Article6
Cassettes
10 Mixed Notes and Checks
Escrow
50 Mixed Notes and Checks
/1 transaction
Capacity
Deposit
Reject
50 Mixed Notes and Checks
/1 transaction
Processing
Time
Deposit
Time
1 Note : - Seconds,
1 Check : - Seconds
Deposit
Time
5 Notes & 2 Checks
: Less than 30 Seconds
25 Notes & 25 Checks :
: Less than 30 Seconds
Storage
1 Sheet : - Seconds

Operator Manual Chapter2. Introduction
© Nautilus Hyosung, Inc. All Rights Reserved. 2-5
Item
Specification
Remarks (Option)
Time
7 Sheets : - Seconds
50 Sheets : - Seconds
Image scanning
Double side scanning
200 dpi
MICR
CMC-7, E13-B
Endorsement Print
Double side printing, Ink jet
Shutter Type
Automatic Shutter
JPR
Journal Printer
Electronic Journal
Dot JPR/ T-JPR Option
Advert
Panel
Advert Panel
LED Backlight Lamp
Status Display Light
(Red/Green)
VFD Option
Statement
Printer
Statement Printer
-
Option
Safety
&
Security
Safety
UL 291 Level-1( Access)
Body Cover
Steel
Locking device
Cencon Lock
Dual Lock (Dual Combo
Lock), Single Combo Lock
Option
Key Lock
Common Key
Alarm
Seismic + Heat Sensor
Security
Terminal Block (External I/F)
Camera
CCD Camera
Face
Camera I/F
Video Port /w Pig Tail for
internal Cam
Video Power /w Pig Tail for
Cam
Mirror
Awareness Mirror
Additional
function
Audio guidance
Sound Card On-Board
ADAAudio guidance
Available(/w Earphone jack
cover/plug)
Dimension (H X W X D)
About 1,591 X 1,048 X 950
(mm)
Dimension
&
Environment
Install Method
Anchor
Weight
About 1220Kg
Battery
System Battery
Alarm Battery Option
Heater
3 Heater
(Upper/Bottom Left/Bottom
Right)

Chapter2. Introduction Operator Manual
2-6 © Nautilus Hyosung, Inc. All Rights Reserved.
Devices of MX7600I
CE (Control Electronics, PC)
►The Control Electronics mainly consist of a motherboard, HDD, DVD-RW, multiple serial card,
and so on.
Basic functions of the control electronics used in this ATM is similar to that of a personal
computer you may have in your office or home with exception of a multiple USB HUB used to
communicate with several devices such as a cash dispenser, card reader, receipt printer and
EPP.
Basic Specification & Sample Picture

Operator Manual Chapter2. Introduction
© Nautilus Hyosung, Inc. All Rights Reserved. 2-7
Customer Display & Keypad
►The customer display welcomes the customer and provides instructions for performing
transactions at the ATM. During the transaction sequence, the ATM prompts the customer to use
the customer keypad to enter transaction information. The 16-key keypad uses a security module
and encryption PIN pad technology to secure the information entered by the customer at the
keypad. The optional function keypads are made up of four keys mounted on each side of the
customer display. The customer selects from the choices shown on the consumer display and
presses the corresponding function key. A touch screen display eliminates the need for function
keypads.
Basic Specification & Sample Picture
Customer Display
with Touch Screen
Encryption
PIN Pad
Teller Display

Chapter2. Introduction Operator Manual
2-8 © Nautilus Hyosung, Inc. All Rights Reserved.
Cash Dispenser Unit
►The cash dispenser delivers media (cash) to the customer after the customer's request is
processed by the network and the software. The media is drawn from the cassettes and
transported to an entrance in the fascia of the ATM, where the customer can receive it. If the
media is too mutilated or wrinkled to dispense, or if a multiple pick occurs, the dispenser sends
the notes to the reject/retract cassette.
Basic Specification & Sample Picture