Otto Bock Genium X3 User manual

INFORMATION
This brochure does not replace the detailed information on the handling and safety of your product
provided in the instructions for use. Please be sure to read the 647G764 Instructions for Use (Qualied
Personnel) attentively!
Genium X3– Bionic Prosthetic System
3B5-X3/3B5-X3=ST
Information and Safety Signals
Information for Practitioner

Note: When the mute mode is active, all vibration and beep signals are disabled.
Vibration signal
3x
3x
5x
Bouncing recognized
to switch
1st
MyMode
activated
2nd
MyMode
activated
Beep signal after bouncing up and down* in basic mode
* switching by bouncing up and down has to be activated in X-Soft
** 4x bouncing up and down has to be activated in X-Soft
2x
3x
2x
3x
+
+
+
Return to
basic
mode***
Beep signal after bouncing up and down in MyMode
*** return to basic mode is also possible by attaching the charger
≥ 3x
continuous
1x
every 5 seconds
+
+
+
1s
1s
1s
3x
4x**
1x 1x
1x 1x
1x 1x
1x
1x
Bouncing recognized
to switch
Bouncing recognized
to switch
Charging status 25%
Charging status 10%
Charging status 0%
or no functionality
Charger attached to
knee joint
Hydraulic system
overheated
Genium X3 – Bionic Prosthetic System

Note: For further information see back of this brochure
Colours used:
Deep sleep mode
activated
+
Charger removed;
Warning
every minute AXON Tube Adapter
disconnected
Charging status
5%
30x
10x
5x
1x
5x
Critical error
Warning
Information
Error
no action required
action required soon
action required immediately
10x
5 minutes
intermittent
(periodically interrupted)
Symbols used:
short
beep signal
short
vibration signal
long
beep signal
long
vibration signal
+
+
+
+
Beep and
vibration signal
Information and Safety Signals
Using the Remote Control
1x 1x
+
3x 3x
+
1x
Selected MyMode
activated
Charger removed,
selftest OK
Error

Last update 26.11.2014
© Ottobock · 647G887=EN-02-1411
If assistance is required during the start-up, use or maintenance of the product, as well as in the event of
unexpected operating behaviour or circumstances, contact the Ottobock office responsible for your country.
Type of
error
Event User restriction Required action
Warning e.g. service interval has
expired No restriction Consult Ottobock
Hydraulic
system
overheated
Overheating of the
hydraulic unit e.g. due to
uninterrupted, increased
activity
Reduced activity
Allow the hydraulic unit
to cool down by reducing
activity
Error
e.g. a sensor
(tube adapter, triple sen-
sor, ...) is not operating
Walking possible with
restrictions
Restart the knee joint by
attaching and removing the
inductive charger (up to
three times);
If error remains, consult
Ottobock immediately
Selftest failure
(if signals occur after
removing the charger)
AXON
Tube Adapter
disconnected
AXON Tube Adapter has
been disconnected while
the knee joint is activated
and the inductive
charger is not attached Connect the
AXON Tube Adapter
AXON Tube Adapter
not connected while
removing the inductive
charger
Critical error
e.g. failure of the valve
drive High stance resistance
Swing phase no longer
possible
Restart the knee joint by
attaching and removing the
inductive charger (up to
three times);
If error remains, consult
Ottobock immediately
Selftest failure
(if signals occur after
removing the charger)
Charging
Status 0% No electronic
functionality
Activation of safety mode
Swing phase no longer
possible
Charging required
No functionality Consult Ottobock
immediately
Error code on
the display of
the Remote
Control
Consult Ottobock
immediately
(Error code number
required)
Otto Bock Healthcare Products GmbH
Brehmstraße 16 · 1110 Wien · Austria
T [phone] · F [phone]
[email protected] · www.ottobock.com