PAX A30 User manual
Quick Setup Guide
PAX TECHNOLOGY INC.
PAX TECHNOLOGY INC.
Note: Product images shown may be different than actual product
received
A30 Smart Payment Terminal
PAX TECHNOLOGY INC.
4.2 Smart Card Reader
Insert the card fully into the reader with the metallic contacts facing up
and towards the device. Make sure that the card is fully inserted into the
card reader while scanning the card.
4.3 Contactless Card Reader
The contactless card reader reads cards and devices placed roughly
within an inch (2.5 mm). For best results, place as close to the reader as
possible and center the card over the indicated area at the back of the
terminal.
Environment
5
Working Environment： Temperature: -10℃~50℃(14℉~122℉)
Humidity: 5%~95%(non-condense)
Storage Environment： Temperature: -20℃~70℃(-4℉~158℉)
Humidity: 5%~95%(non-condense)
6
Cleaning the Device
Do not use industrial strength or abrasive cleaner as it may damage or
scratch the screen.
Do not immerse the device in water or liquid.
Do not spray water or cleaner into EMV Card Reader or ports.
To clean the screen, apply distilled water or mild glass cleaner onto a
soft, lint-free cloth and gently wipe terminal.
7
Terminal Installation and Usage Tips
1) If any cables become damaged, seek a replacement.
2) Before inserting card, please check the inside and periphery of the IC
card slot. If there is any suspicious object, please report to the related
administrator.
3) Do not insert unknown materials into any port on the A30, this may
cause serious damage.
4) If repairs are required, please contact a professional technician
instead of attempting them on your own.
5) Avoid exposing the device to an excessively hot, dusty, or strong
electromagnetic environment.
6) Do not vibrate, shake, or drop the device.
CAUTION: Changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority
to operate the equipment.
8
Icon Key
Do not throw away; Recycle only.
Class II Equipment
For indoor use only
Energy Efficiency Marking
VI
~AC voltage
DC voltage
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
FCC Compliance Statement
FCC WARNING
This equipment complies with Part 68 of the FCC rules and the
requirements adopted by the ACTA. On the body of this equipment is
a label that contains, among other information, a product identifier. If
requested, this number must be provided to the telephone company.
RF Exposure Information
This device meets the government's requirement for exposure to radio
waves. This device is designed and manufactured not to exceed the
emission limits for exposure to radio frequency (RF) energy set by the
Federal Communications Commission of the U.S. Government.
PAX Customer Support
For questions or help with the terminal installation please contact your
service provider or PAX customer support.
P/N:200312000000554
PAX TECHNOLOGY INC.
PAX TECHNOLOGY INC.
This document is provided to you for informational purposes
only. All features and specifications are subject to change
without notice. PAX’s name and PAX’s logo are registered
trademarks of PAX Technology Inc. All rights reserved.
Responsible Party:
PAX Technology, Inc.
8880 Freedom Crossing Trail
Building 400, 3rd Floor, Suite 300
Jacksonville, FL 32256, USA
Help Desk
1-877-859-0099
www.pax.us
A30 Smart Payment Terminal
USB Cable
Quick Setup Guide
Please check the components after unpacking. If any are missing,
or if there is a page missing from the product manual, etc., please
contact the dealer.
Name
Bottom View
Wall Hanging Hole
Charging Contact
Speaker
Audio Jack
NFC Reading
Area
NFC Light
Camera
Swipe Card
Slot
Touch Screen
Power
Volume +
Volume -
Keyboard
IC Card Slot
Mic
Top View
LAN
RS232
PUSB
USB
Powered USB Cable (Optional)
AC Power Cable (Optional)
Adapter (Optional)
LAN A-POE
LAN B
USB
Defualt
Optional
LAN A
LAN B
PUSB
USB
Optional
Front View
Instructions
The A30 has one SAM card slot on the main body of the device and one
SD card slot. These card slots are normally hidden under the back cover.
In order to install a SD or SAM card into any of these slots, insert a card
into the card slot with the contacts facing upwards and the clipped corner
of the card facing forward and to the right.
SAM Card SD Card
The following sections cover basic operating instructions.
3.1 Power ON/OFF
POWER ON:
Plug the terminal into an electric outlet; the terminal will power on
automatically.
POWER OFF:
Press and hold the power button down for 3 to 5 seconds and then
release.
3.2 SAM/SD Card Installation
1)Unscrew the back cover.
2)Push the cover to the right.
3)Insert SAM /Micro-SD card into the appropriate card slot and replace
cover.
3.3 Stand Installation
The following instructions cover A30 stand installation.
1)Align and insert metal stand prongs into the stand slots (3) on underside
of terminal.
2)Slide terminal firmly into place on stand.
Card Readers
The A30 comes with a Magnetic Stripe Reader, a Smart Card Reader,
and a Contactless Card Reader.
4.1 Magnetic Stripe Card
Slide the card through the card reader slot from left to right or from right
to left with the magnetic strip oriented towards the body of the device.
Make sure that the card is fully inserted into the card reader while swiping
the card.
P/N:200312000000554
PAX TECHNOLOGY INC.
PAX TECHNOLOGY INC.
This document is provided to you for informational purposes
only. All features and specifications are subject to change
without notice. PAX’s name and PAX’s logo are registered
trademarks of PAX Technology Inc. All rights reserved.
Responsible Party:
PAX Technology, Inc.
8880 Freedom Crossing Trail
Building 400, 3rd Floor, Suite 300
Jacksonville, FL 32256, USA
Help Desk
1-877-859-0099
www.pax.us
A30 Smart Payment Terminal
USB Cable
Quick Setup Guide
Please check the components after unpacking. If any are missing,
or if there is a page missing from the product manual, etc., please
contact the dealer.
Name
Bottom View
Wall Hanging Hole
Charging Contact
Speaker
Audio Jack
NFC Reading
Area
NFC Light
Camera
Swipe Card
Slot
Touch Screen
Power
Volume +
Volume -
Keyboard
IC Card Slot
Mic
Top View
LAN
RS232
PUSB
USB
Powered USB Cable (Optional)
AC Power Cable (Optional)
Adapter (Optional)
LAN A-POE
LAN B
USB
Defualt
Optional
LAN A
LAN B
PUSB
USB
Optional
Front View
Instructions
The A30 has one SAM card slot on the main body of the device and one
SD card slot. These card slots are normally hidden under the back cover.
In order to install a SD or SAM card into any of these slots, insert a card
into the card slot with the contacts facing upwards and the clipped corner
of the card facing forward and to the right.
SAM Card SD Card
The following sections cover basic operating instructions.
3.1 Power ON/OFF
POWER ON:
Plug the terminal into an electric outlet; the terminal will power on
automatically.
POWER OFF:
Press and hold the power button down for 3 to 5 seconds and then
release.
3.2 SAM/SD Card Installation
1)Unscrew the back cover.
2)Push the cover to the right.
3)Insert SAM /Micro-SD card into the appropriate card slot and replace
cover.
3.3 Stand Installation
The following instructions cover A30 stand installation.
1)Align and insert metal stand prongs into the stand slots (3) on underside
of terminal.
2)Slide terminal firmly into place on stand.
Card Readers
The A30 comes with a Magnetic Stripe Reader, a Smart Card Reader,
and a Contactless Card Reader.
4.1 Magnetic Stripe Card
Slide the card through the card reader slot from left to right or from right
to left with the magnetic strip oriented towards the body of the device.
Make sure that the card is fully inserted into the card reader while swiping
the card.
P/N:200312000000554
PAX TECHNOLOGY INC.
PAX TECHNOLOGY INC.
This document is provided to you for informational purposes
only. All features and specifications are subject to change
without notice. PAX’s name and PAX’s logo are registered
trademarks of PAX Technology Inc. All rights reserved.
Responsible Party:
PAX Technology, Inc.
8880 Freedom Crossing Trail
Building 400, 3rd Floor, Suite 300
Jacksonville, FL 32256, USA
Help Desk
1-877-859-0099
www.pax.us
A30 Smart Payment Terminal
USB Cable
Quick Setup Guide
Please check the components after unpacking. If any are missing,
or if there is a page missing from the product manual, etc., please
contact the dealer.
Name
Bottom View
Wall Hanging Hole
Charging Contact
Speaker
Audio Jack
NFC Reading
Area
NFC Light
Camera
Swipe Card
Slot
Touch Screen
Power
Volume +
Volume -
Keyboard
IC Card Slot
Mic
Top View
LAN
RS232
PUSB
USB
Powered USB Cable (Optional)
AC Power Cable (Optional)
Adapter (Optional)
LAN A-POE
LAN B
USB
Defualt
Optional
LAN A
LAN B
PUSB
USB
Optional
Front View
Instructions
The A30 has one SAM card slot on the main body of the device and one
SD card slot. These card slots are normally hidden under the back cover.
In order to install a SD or SAM card into any of these slots, insert a card
into the card slot with the contacts facing upwards and the clipped corner
of the card facing forward and to the right.
SAM Card SD Card
The following sections cover basic operating instructions.
3.1 Power ON/OFF
POWER ON:
Plug the terminal into an electric outlet; the terminal will power on
automatically.
POWER OFF:
Press and hold the power button down for 3 to 5 seconds and then
release.
3.2 SAM/SD Card Installation
1)Unscrew the back cover.
2)Push the cover to the right.
3)Insert SAM /Micro-SD card into the appropriate card slot and replace
cover.
3.3 Stand Installation
The following instructions cover A30 stand installation.
1)Align and insert metal stand prongs into the stand slots (3) on underside
of terminal.
2)Slide terminal firmly into place on stand.
Card Readers
The A30 comes with a Magnetic Stripe Reader, a Smart Card Reader,
and a Contactless Card Reader.
4.1 Magnetic Stripe Card
Slide the card through the card reader slot from left to right or from right
to left with the magnetic strip oriented towards the body of the device.
Make sure that the card is fully inserted into the card reader while swiping
the card.
P/N:200312000000554
PAX TECHNOLOGY INC.
PAX TECHNOLOGY INC.
This document is provided to you for informational purposes
only. All features and specifications are subject to change
without notice. PAX’s name and PAX’s logo are registered
trademarks of PAX Technology Inc. All rights reserved.
Responsible Party:
PAX Technology, Inc.
8880 Freedom Crossing Trail
Building 400, 3rd Floor, Suite 300
Jacksonville, FL 32256, USA
Help Desk
1-877-859-0099
www.pax.us
A30 Smart Payment Terminal
USB Cable
Quick Setup Guide
Please check the components after unpacking. If any are missing,
or if there is a page missing from the product manual, etc., please
contact the dealer.
Name
Bottom View
Wall Hanging Hole
Charging Contact
Speaker
Audio Jack
NFC Reading
Area
NFC Light
Camera
Swipe Card
Slot
Touch Screen
Power
Volume +
Volume -
Keyboard
IC Card Slot
Mic
Top View
LAN
RS232
PUSB
USB
Powered USB Cable (Optional)
AC Power Cable (Optional)
Adapter (Optional)
LAN A-POE
LAN B
USB
Defualt
Optional
LAN A
LAN B
PUSB
USB
Optional
Front View
Instructions
The A30 has one SAM card slot on the main body of the device and one
SD card slot. These card slots are normally hidden under the back cover.
In order to install a SD or SAM card into any of these slots, insert a card
into the card slot with the contacts facing upwards and the clipped corner
of the card facing forward and to the right.
SAM Card SD Card
The following sections cover basic operating instructions.
3.1 Power ON/OFF
POWER ON:
Plug the terminal into an electric outlet; the terminal will power on
automatically.
POWER OFF:
Press and hold the power button down for 3 to 5 seconds and then
release.
3.2 SAM/SD Card Installation
1)Unscrew the back cover.
2)Push the cover to the right.
3)Insert SAM /Micro-SD card into the appropriate card slot and replace
cover.
3.3 Stand Installation
The following instructions cover A30 stand installation.
1)Align and insert metal stand prongs into the stand slots (3) on underside
of terminal.
2)Slide terminal firmly into place on stand.
Card Readers
The A30 comes with a Magnetic Stripe Reader, a Smart Card Reader,
and a Contactless Card Reader.
4.1 Magnetic Stripe Card
Slide the card through the card reader slot from left to right or from right
to left with the magnetic strip oriented towards the body of the device.
Make sure that the card is fully inserted into the card reader while swiping
the card.
Quick Setup Guide
PAX TECHNOLOGY INC.
PAX TECHNOLOGY INC.
Note: Product images shown may be different than actual product
received
A30 Smart Payment Terminal
PAX TECHNOLOGY INC.
4.2 Smart Card Reader
Insert the card fully into the reader with the metallic contacts facing up
and towards the device. Make sure that the card is fully inserted into the
card reader while scanning the card.
4.3 Contactless Card Reader
The contactless card reader reads cards and devices placed roughly
within an inch (2.5 mm). For best results, place as close to the reader as
possible and center the card over the indicated area at the back of the
terminal.
Environment
5
Working Environment： Temperature: -10℃~50℃(14℉~122℉)
Humidity: 5%~95%(non-condense)
Storage Environment： Temperature: -20℃~70℃(-4℉~158℉)
Humidity: 5%~95%(non-condense)
6
Cleaning the Device
Do not use industrial strength or abrasive cleaner as it may damage or
scratch the screen.
Do not immerse the device in water or liquid.
Do not spray water or cleaner into EMV Card Reader or ports.
To clean the screen, apply distilled water or mild glass cleaner onto a
soft, lint-free cloth and gently wipe terminal.
7
Terminal Installation and Usage Tips
1) If any cables become damaged, seek a replacement.
2) Before inserting card, please check the inside and periphery of the IC
card slot. If there is any suspicious object, please report to the related
administrator.
3) Do not insert unknown materials into any port on the A30, this may
cause serious damage.
4) If repairs are required, please contact a professional technician
instead of attempting them on your own.
5) Avoid exposing the device to an excessively hot, dusty, or strong
electromagnetic environment.
6) Do not vibrate, shake, or drop the device.
CAUTION: Changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority
to operate the equipment.
8
Icon Key
Do not throw away; Recycle only.
Class II Equipment
For indoor use only
Energy Efficiency Marking
VI
~AC voltage
DC voltage
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
FCC Compliance Statement
FCC WARNING
This equipment complies with Part 68 of the FCC rules and the
requirements adopted by the ACTA. On the body of this equipment is
a label that contains, among other information, a product identifier. If
requested, this number must be provided to the telephone company.
RF Exposure Information
This device meets the government's requirement for exposure to radio
waves. This device is designed and manufactured not to exceed the
emission limits for exposure to radio frequency (RF) energy set by the
Federal Communications Commission of the U.S. Government.
PAX Customer Support
For questions or help with the terminal installation please contact your
service provider or PAX customer support.
Quick Setup Guide
PAX TECHNOLOGY INC.
PAX TECHNOLOGY INC.
Note: Product images shown may be different than actual product
received
A30 Smart Payment Terminal
PAX TECHNOLOGY INC.
4.2 Smart Card Reader
Insert the card fully into the reader with the metallic contacts facing up
and towards the device. Make sure that the card is fully inserted into the
card reader while scanning the card.
4.3 Contactless Card Reader
The contactless card reader reads cards and devices placed roughly
within an inch (2.5 mm). For best results, place as close to the reader as
possible and center the card over the indicated area at the back of the
terminal.
Environment
5
Working Environment： Temperature: -10℃~50℃(14℉~122℉)
Humidity: 5%~95%(non-condense)
Storage Environment： Temperature: -20℃~70℃(-4℉~158℉)
Humidity: 5%~95%(non-condense)
6
Cleaning the Device
Do not use industrial strength or abrasive cleaner as it may damage or
scratch the screen.
Do not immerse the device in water or liquid.
Do not spray water or cleaner into EMV Card Reader or ports.
To clean the screen, apply distilled water or mild glass cleaner onto a
soft, lint-free cloth and gently wipe terminal.
7
Terminal Installation and Usage Tips
1) If any cables become damaged, seek a replacement.
2) Before inserting card, please check the inside and periphery of the IC
card slot. If there is any suspicious object, please report to the related
administrator.
3) Do not insert unknown materials into any port on the A30, this may
cause serious damage.
4) If repairs are required, please contact a professional technician
instead of attempting them on your own.
5) Avoid exposing the device to an excessively hot, dusty, or strong
electromagnetic environment.
6) Do not vibrate, shake, or drop the device.
CAUTION: Changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority
to operate the equipment.
8
Icon Key
Do not throw away; Recycle only.
Class II Equipment
For indoor use only
Energy Efficiency Marking
VI
~AC voltage
DC voltage
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
FCC Compliance Statement
FCC WARNING
This equipment complies with Part 68 of the FCC rules and the
requirements adopted by the ACTA. On the body of this equipment is
a label that contains, among other information, a product identifier. If
requested, this number must be provided to the telephone company.
RF Exposure Information
This device meets the government's requirement for exposure to radio
waves. This device is designed and manufactured not to exceed the
emission limits for exposure to radio frequency (RF) energy set by the
Federal Communications Commission of the U.S. Government.
PAX Customer Support
For questions or help with the terminal installation please contact your
service provider or PAX customer support.
Quick Setup Guide
PAX TECHNOLOGY INC.
PAX TECHNOLOGY INC.
Note: Product images shown may be different than actual product
received
A30 Smart Payment Terminal
PAX TECHNOLOGY INC.
4.2 Smart Card Reader
Insert the card fully into the reader with the metallic contacts facing up
and towards the device. Make sure that the card is fully inserted into the
card reader while scanning the card.
4.3 Contactless Card Reader
The contactless card reader reads cards and devices placed roughly
within an inch (2.5 mm). For best results, place as close to the reader as
possible and center the card over the indicated area at the back of the
terminal.
Environment
5
Working Environment： Temperature: -10℃~50℃(14℉~122℉)
Humidity: 5%~95%(non-condense)
Storage Environment： Temperature: -20℃~70℃(-4℉~158℉)
Humidity: 5%~95%(non-condense)
6
Cleaning the Device
Do not use industrial strength or abrasive cleaner as it may damage or
scratch the screen.
Do not immerse the device in water or liquid.
Do not spray water or cleaner into EMV Card Reader or ports.
To clean the screen, apply distilled water or mild glass cleaner onto a
soft, lint-free cloth and gently wipe terminal.
7
Terminal Installation and Usage Tips
1) If any cables become damaged, seek a replacement.
2) Before inserting card, please check the inside and periphery of the IC
card slot. If there is any suspicious object, please report to the related
administrator.
3) Do not insert unknown materials into any port on the A30, this may
cause serious damage.
4) If repairs are required, please contact a professional technician
instead of attempting them on your own.
5) Avoid exposing the device to an excessively hot, dusty, or strong
electromagnetic environment.
6) Do not vibrate, shake, or drop the device.
CAUTION: Changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority
to operate the equipment.
8
Icon Key
Do not throw away; Recycle only.
Class II Equipment
For indoor use only
Energy Efficiency Marking
VI
~AC voltage
DC voltage
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
FCC Compliance Statement
FCC WARNING
This equipment complies with Part 68 of the FCC rules and the
requirements adopted by the ACTA. On the body of this equipment is
a label that contains, among other information, a product identifier. If
requested, this number must be provided to the telephone company.
RF Exposure Information
This device meets the government's requirement for exposure to radio
waves. This device is designed and manufactured not to exceed the
emission limits for exposure to radio frequency (RF) energy set by the
Federal Communications Commission of the U.S. Government.
PAX Customer Support
For questions or help with the terminal installation please contact your
service provider or PAX customer support.
Quick Setup Guide
PAX TECHNOLOGY INC.
PAX TECHNOLOGY INC.
Note: Product images shown may be different than actual product
received
A30 Smart Payment Terminal
PAX TECHNOLOGY INC.
4.2 Smart Card Reader
Insert the card fully into the reader with the metallic contacts facing up
and towards the device. Make sure that the card is fully inserted into the
card reader while scanning the card.
4.3 Contactless Card Reader
The contactless card reader reads cards and devices placed roughly
within an inch (2.5 mm). For best results, place as close to the reader as
possible and center the card over the indicated area at the back of the
terminal.
Environment
5
Working Environment： Temperature: -10℃~50℃(14℉~122℉)
Humidity: 5%~95%(non-condense)
Storage Environment： Temperature: -20℃~70℃(-4℉~158℉)
Humidity: 5%~95%(non-condense)
6
Cleaning the Device
Do not use industrial strength or abrasive cleaner as it may damage or
scratch the screen.
Do not immerse the device in water or liquid.
Do not spray water or cleaner into EMV Card Reader or ports.
To clean the screen, apply distilled water or mild glass cleaner onto a
soft, lint-free cloth and gently wipe terminal.
7
Terminal Installation and Usage Tips
1) If any cables become damaged, seek a replacement.
2) Before inserting card, please check the inside and periphery of the IC
card slot. If there is any suspicious object, please report to the related
administrator.
3) Do not insert unknown materials into any port on the A30, this may
cause serious damage.
4) If repairs are required, please contact a professional technician
instead of attempting them on your own.
5) Avoid exposing the device to an excessively hot, dusty, or strong
electromagnetic environment.
6) Do not vibrate, shake, or drop the device.
CAUTION: Changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority
to operate the equipment.
8
Icon Key
Do not throw away; Recycle only.
Class II Equipment
For indoor use only
Energy Efficiency Marking
VI
~AC voltage
DC voltage
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
FCC Compliance Statement
FCC WARNING
This equipment complies with Part 68 of the FCC rules and the
requirements adopted by the ACTA. On the body of this equipment is
a label that contains, among other information, a product identifier. If
requested, this number must be provided to the telephone company.
RF Exposure Information
This device meets the government's requirement for exposure to radio
waves. This device is designed and manufactured not to exceed the
emission limits for exposure to radio frequency (RF) energy set by the
Federal Communications Commission of the U.S. Government.
PAX Customer Support
For questions or help with the terminal installation please contact your
service provider or PAX customer support.
P/N:200312000000554
PAX TECHNOLOGY INC.
PAX TECHNOLOGY INC.
This document is provided to you for informational purposes
only. All features and specifications are subject to change
without notice. PAX’s name and PAX’s logo are registered
trademarks of PAX Technology Inc. All rights reserved.
Responsible Party:
PAX Technology, Inc.
8880 Freedom Crossing Trail
Building 400, 3rd Floor, Suite 300
Jacksonville, FL 32256, USA
Help Desk
1-877-859-0099
www.pax.us
A30 Smart Payment Terminal
USB Cable
Quick Setup Guide
Please check the components after unpacking. If any are missing,
or if there is a page missing from the product manual, etc., please
contact the dealer.
Name
Bottom View
Wall Hanging Hole
Charging Contact
Speaker
Audio Jack
NFC Reading
Area
NFC Light
Camera
Swipe Card
Slot
Touch Screen
Power
Volume +
Volume -
Keyboard
IC Card Slot
Mic
Top View
LAN
RS232
PUSB
USB
Powered USB Cable (Optional)
AC Power Cable (Optional)
Adapter (Optional)
LAN A-POE
LAN B
USB
Defualt
Optional
LAN A
LAN B
PUSB
USB
Optional
Front View
Instructions
The A30 has one SAM card slot on the main body of the device and one
SD card slot. These card slots are normally hidden under the back cover.
In order to install a SD or SAM card into any of these slots, insert a card
into the card slot with the contacts facing upwards and the clipped corner
of the card facing forward and to the right.
SAM Card SD Card
The following sections cover basic operating instructions.
3.1 Power ON/OFF
POWER ON:
Plug the terminal into an electric outlet; the terminal will power on
automatically.
POWER OFF:
Press and hold the power button down for 3 to 5 seconds and then
release.
3.2 SAM/SD Card Installation
1)Unscrew the back cover.
2)Push the cover to the right.
3)Insert SAM /Micro-SD card into the appropriate card slot and replace
cover.
3.3 Stand Installation
The following instructions cover A30 stand installation.
1)Align and insert metal stand prongs into the stand slots (3) on underside
of terminal.
2)Slide terminal firmly into place on stand.
Card Readers
The A30 comes with a Magnetic Stripe Reader, a Smart Card Reader,
and a Contactless Card Reader.
4.1 Magnetic Stripe Card
Slide the card through the card reader slot from left to right or from right
to left with the magnetic strip oriented towards the body of the device.
Make sure that the card is fully inserted into the card reader while swiping
the card.
Table of contents
Other PAX Payment Terminal manuals
