PROAIM PF-4TR User manual

23.9ft Fraser (PF-4TR) Jib crane with
PT-1000 Pan tilt head, FR-TS Stand and
FR-D Dolly
(PF-4TR-PP)
INSTRUCTION MANUAL
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any
means, electronic, mechanical, photocopying, recording, or otherwise, except as may be expressly permied by
the applicable copyright statutes or in wring by the Publisher.

Proaim 23.9 Fraser (PF-4TR) Jib crane with PT-1000 Pan lt head, FR-TS Stand and FR-D Dolly 2
INTRODUCTION
PROAIM presents a fully professional 23.9 Fraser lm producon package, a perfect lming
soluon to increase your producon value. Fraser, a DV & Eng jib system has numerous features
to support & oer great performance. It is compable with many types of DV, HDV &broad
casng camera.
The triangular jib crane with high-intensity aluminium alloy structure ts smoothly & securely
with one another providing super rigidity and strength. Precisely designed 2-axis pan-lt
head adds creavity to your shots. Accompanied with various other benets, it completes the
package which is designed to enhance the cinemac quality.
IN THE BOX
Please inspect the contents of your shipped package to ensure you have received all that is
pictured and listed below.
Jib Secons
Jib Stand
Cables length & Qty :
(Red) 14 5 inch-1
(Red) 6 8 inch—1
(Red) 4 7inch—1
(Red) 3 8 inch—1
Cable Guide support rod
Hub locking knob
(Blue) 18 8 inch-1
(Blue)10 10inch-1
(Yellow)17 2inch-1
Dolly
Monitor Supporting Rods
Weight rod with weight closer
Locking pin

Proaim 23.9 Fraser (PF-4TR) Jib crane with PT-1000 Pan lt head, FR-TS Stand and FR-D Dolly 3
2 X joysck wires
1.(blue ring)
2.(yellow ring)
8meter 7 pin to 7 pin
XLR male wire (1PC)
5 pin lemo male to male
connecng wire (1PC)
3.5mm jack male to male
connecng wire (1 PC)
8meter BNC to BNC long
Connecng Wire (1PC)
4 pin XLR male to female
connecng wire (1PC)
2.5mm jack male to male
connecng wire(1PC) Lemo to din
connecng wire
(1PC)
1 meter BNC connecng
wire(1PC)
Pan Tilt Head 4X Knob
1x motor holding rod Focus & iris
Main Controlling box
Head control
handle
Camera control
handle
lemo to push or pull
connecng wire (1PC)
Main Ac adapter
(1 PC)
Pan lt wires

Proaim 23.9 Fraser (PF-4TR) Jib crane with PT-1000 Pan lt head, FR-TS Stand and FR-D Dolly 4
 Take out the bolt from the center of dolly and spread it on floor. Then put the bolt back through
the center of dolly again.
Note: To keep the dolly in stac posion
(non-movable), Lock down the wheels.
ASSEMBLING THE DOLLY
 Stretch the legs of jib stand on oor and in order to set the height of stand, loosen the bolts on
legs with the help of allen key and insert the locking pin for extra security of stand legs.
ATTACHING THE JIB STAND

Proaim 23.9 Fraser (PF-4TR) Jib crane with PT-1000 Pan lt head, FR-TS Stand and FR-D Dolly 5
 Now mount the jib Stand onto the dolly.
 Place the secon 2 with hub mounng on stand and ghten it with the hub locking knob to
secure it properly.
NOTE: For assembling the jib crane, Lock the pan and lt knobs.
Pan locking
knob.
Tilt Locking
knob

Proaim 23.9 Fraser (PF-4TR) Jib crane with PT-1000 Pan lt head, FR-TS Stand and FR-D Dolly 6
 Aach rst secon with second secon and ghten the allen bolts to secure it.
 Aach cable guide support rod to cable guide clamp on secon-2 and ghten the allen bolts
secon properly to secure it. Then aach the cable guide support rod onto the cable guide
clamp.
 Loosen the allen bolt, in order to
aach cable guide support rod to it.
ATTACHING THE CABLE GUIDE RODS
NOTE : Aach the rest of the secons in the same way starng from the other end of secon 2.

Proaim 23.9 Fraser (PF-4TR) Jib crane with PT-1000 Pan lt head, FR-TS Stand and FR-D Dolly 7
 Now aach hook to the cable guide rod on jib Secon-2. Then aach 4.7 red cable into the
hook & connect it to the clamp on jib secon –1.
 Now repeat the same steps to connect
the 3 8 inch cable from jib secon-2
and aach with clamp on jib secon-1
to clamp on jib secon : 1.
Cable code (red)
ATTACHING THE STABILITY CABLES
 Mount another hook to the cable guide rod on jib secon-2 then aach 6.8 red cable to the
hook and further clamp it on jib Secon-4 & adjust the cable with the help of wire tensioner.
Note: Repeat the same steps to connect 14.5 cable from jib Secon-2 with clamp on jib Secon-6
NOTE: You can adjust the cable with the help of wire tensioner.

Proaim 23.9 Fraser (PF-4TR) Jib crane with PT-1000 Pan lt head, FR-TS Stand and FR-D Dolly 8
 Aach 10.10 blue cable to the clamp on jib Secon-4 & aach it further to the clamp on Jib
Secon-1 & repeat the same steps for other side.
Cable code (blue)
 Align the cables to the cables guide side
rod.
 Note: Repeat the same steps to connect 18.8 blue cable to the clamp on jib Secon-6 &
aach it further to the clamp Jib Secon-1 & repeat the same steps for other side.
 Aach the 17.2 yellow cable to the hub secon and aach it with the head secon of jib
and adjusng the cable with the help of wire tensioner.
Cable code (Yellow)

Proaim 23.9 Fraser (PF-4TR) Jib crane with PT-1000 Pan lt head, FR-TS Stand and FR-D Dolly 9
 Aach the pan-lt head to the Head plate of crane and and secure it with the help of knobs.
ATTACHING THE PAN TILT HEAD
knobs
 Mount your camera on the mounng plate of pan lt head with the help of provided
checknut.
 Insert the silver 15mm rod into the
camera sliding plate to aach iris and
focus gear.

Proaim 23.9 Fraser (PF-4TR) Jib crane with PT-1000 Pan lt head, FR-TS Stand and FR-D Dolly 10
 Similarly, plug the lemo to din connector wire from camera to circuit board.
 Now Insert the gear into 15mm rod and aach the gear to the iris & lens focusing & iris ring of
your camera. Then plug the iris & focus cable from camera to circuit board.
 Plug the 5 pin male to male lemo wire from head to circuit board of head.