Qlight S100S User manual

ww w.qlight.com
S100S / S125S
Thank you for purchasing QLight product. Please read this
manual carefully before installing this product for safe and long
use.
▪Suitable for a bright place and a signal transfer for a long
distance with a strong strobe signal light.
▪Easy to change its lamp by taking a connector type lamp.
▪Material : Lens-AS, Body-ABS
▪Flashes : 60-80/Min.(Continuous flashing of 2 times)
▪Protection Class : IP54
1) S100S
▪ General Specification
Model
Rated
Voltage
Current
Weight
Flashes
Color
S100S
DC12V
1.001A
0.25Kg
60~80/min.
RED-R
AMBER-A
GREEN-G
BLUE-B
DC24V
0.616A
0.25Kg
AC110V
0.133A
0.25Kg
AC220V
0.106A
0.25Kg
▪External View Drawing
S100S
2) S125S
▪ General Specification
Model
Rated
Voltage
Current
Weight
Flashes
Color
S125S
DC12V
1.001A
0.25Kg
60~80/min.
RED-R
AMBER-A
GREEN-G
BLUE-B
DC24V
0.616A
0.25Kg
AC110V
0.133A
0.25Kg
AC220V
0.106A
0.25Kg
▪External View Drawing
S125S
Power line UL1015-NO.18(0.75sq) x 2C 400mm comes out from
the product.
▪In case of product using AC voltage, connect the line without
Polarity(wire color).
▪In case of product using DC voltage, black line is negative(-).
Indoor Outdoor
▪This product was manufactured with the structure for indoor
use. Installing in any direction is okay for indoor use.
▪Outdoor use is limited at a place where no water or very little
water percolates. Mounting also should be done only on the
vertical standing direction.
▪Mount at the place where exists low vibration, low impact, low
moisture and low dust as long as possible.
OPERATING MANUAL
Xenon Lamp Strobe Light

ww w.qlight.com
▪Please make a hole by a drill where you need to attach our
product and refer to below picture for a hole size. (Make sure
PCD from external view drawing.)
▪S100S : Fix the product by using nuts(M4-3EA) originally
equipped on mounting bolt on bottom of the product.
▪S125S : Fix the product by using nuts(M5-3EA) originally
equipped on mounting bolt on bottom of the product.
1) ※Warning!
Must turn off power supply and change bulb after 1 minute at
least.
▪Xenon lamp emits superheat when working. Please be aware
you should not touch bulb before lowering its heat prevent
from a burn.
▪Xenon lamp work with a high voltage, if you touch a
assembling board or lamp without power-off, you may receive
an electric shock.
2) Lens Removal
Remove lens by turning it counterclockwise. Please make sure
the lamp on the assembling board and Steady/Flashing selection
switch.
3) Change Lamp
▪Our company’s xenon lamp (1) is made as a connector type
lamp. If you pull out with a small strength, it can be separated
easily.
▪Please fit the lamp by checking a connector pin location (2) as
below picture.
Lamp removal Lamp fitting
4) Lens Assembling
Assemble the product in reverse order of separating.
▪If using voltage is seriously higher or lower than rated voltage, it
can reduce the self-life of the product or can cause a problem
on product operating. Make sure the using voltage does not
exceed +/-5% of the rated voltage.
▪If lens or body of the product is contaminated by chemicals such
as thinner, benzene, the product can be damaged, discolored
or deformed. Please be careful.
▪Do not give strong impact to the product. It can be a reason of
wire disconnection or short circuit.
▪Do not strongly pull the wire out from the product. It can cause a
disorder.
Situation
Main reason
Solution
Lamp non-working
Damage on Lamp
Change lamp
Lamp connector
badness
Re-connecting lamp
connector
No Power Supply
Making sure power
supply
Strobe working
irregularly.
Supplying voltage
lower than rated
voltage
Making sure using
voltage
(S100S)
(S125S)
Bulb change
QLIGHT CO., LTD.
http://www.qlight.com
E-mail : [e-mail]
Overseas Sales Team / Factory
Tel) [phone] Fax) [phone]
185-25 Mukbang-ro Sangdong-Myeon, Gimhae-Si,
Gyeongsangnam-do, Korea
Inquiry for Product and C/S