Qlight ST45L-ETN-BZ User manual

PB 1
Please scan the QR code for more
detailed product information.
www.qlight.com
Ethernet LED Tower Light
Ordering Specications
Thank you for purchasing Qlight’s products. Please read this user manual carefully
prior to installation and operation to ensure safe and correct use.
1. Please remove any objects that can interrupt ventilation around the product.
2. Please turn o󰀨 the power of the product immediately if it fails to operate properly.
3. Carefully wire the product according to each product’s specication.
4. Please be careful in preventing chemicals such as thinner, benzene, etc. in contact with the surface of the product.
5. Do not apply excessive force/impact to the product.
6. Failure to follow any of the instructions above may cause malfunction or damage to the product, re, and electric shock.
Precautions for Correct Use
Failure to follow the proper instructions may cause damage to property, the product, or malfunction of the product
that would void the warranty.
Precautions for Safety
Failure to follow the instructions below may cause a loss of life or serious physical injury.
1. During wiring or maintenance, please completely turn o󰀨 the power of the product. (Failure to follow this may lead to an electric shock.)
2. Do not install the product in locations that subjects it to excessive dust or water other than the conditions designated by the IP protection
ratings indicated for each product. (Failure to follow these instructions may cause a re to the product, electric shock, physical injury,
malfunction or damage to the product.)
3. Do not alter or repair this product. If maintenance or repair service is required, please contact your local Qlight contact point. (Failure to
follow these instructions may lead to re, electric shock, or product damage.)
4. Please apply the correct voltage to the product. (Failure to follow these instructions may lead to re, electric shock, or product damage.)
5. When the product is applied to a condition that may impact lives or property, please make sure to have a double safety device. (Failure to
follow this may cause damage to property, re, electric shock and loss of life.)
ST45(M)L/ ST56(M)EL/ ST80(M)EL-ETN
5030
23
90dB85dB
ST56EL-ETN-WS
-3-220 -RAG -LW18
[Model number] [Layer] [Voltage] [Color] [Mounting option]
| | | | |
• ST56EL-ETN-BZ
• ST56EL-ETN-WS
• ST56EL-ETN-WM
• ST56EL-ETN-WA
• ST56MEL-ETN-BZ
• ST56MEL-ETN-WS
• ST56MEL-ETN-WM
• ST56MEL-ETN-WA
• Layer 1-1
• Layer 2-2
• Layer 3-3
• Layer 4-4
• Layer 5-5
• 12-DC12V
• 24-DC24V
• 110/220
-AC110-220V
R-Red
A-Amber
G-Green
B-Blue
W-White
• (Blank)
- Standard type
• Mounting type
- LB18 - LW18
- QZ18 - SZ18
- QL18 - SL18
- QLA18
• ST56(M)EL-ETN
• ST45(M)L-ETN
ST45L-ETN-WS
-3-24 -RAG -LW18
[Model number] [Layer] [Voltage] [Color] [Mounting option]
| | | | |
• ST45L-ETN-BZ
• ST45L-ETN-WS
• ST45L-ETN-WM
• ST45L-ETN-WA
• ST45ML-ETN-BZ
• ST45ML-ETN-WS
• ST45ML-ETN-WM
• ST45ML-ETN-WA
• Layer 1-1
• Layer 2-2
• Layer 3-3
• Layer 4-4
• Layer 5-5
• 12-DC12V
• 24-DC24V
• 110/220
-AC110-220V
R-Red
A-Amber
G-Green
B-Blue
W-White
• (Blank)
- Standard type
• Mounting type
- LB18 - LW18
- QZ18 - SZ18
- QL18 - SL18
- QLA18

2 3
Product Specications
ST80EL-ETN-WS
-3-220 -RAG -LW24
[Model number] [Layer] [Voltage] [Color] [Mounting option]
| | | | |
• ST80EL-ETN-BZ
• ST80EL-ETN-WS
• ST80EL-ETN-WM
• ST80EL-ETN-WA
• ST80MEL-ETN-BZ
• ST80MEL-ETN-WS
• ST80MEL-ETN-WM
• ST80MEL-ETN-WA
• Layer 1-1
• Layer 2-2
• Layer 3-3
• Layer 4-4
• Layer 5-5
• 12-DC12V
• 24-DC24V
• 110-AC110V
• 220-AC220V
R-Red
A-Amber
G-Green
B-Blue
W-White
• (Blank)
- Standard type
• Mounting type
- LB24 - LW24
- QZ24 - SZ24
- QL24 - SL24
- QLA24
• ST80(M)EL-ETN
• ST80(M)EL-ETN
Model number Layer Voltage Current Certicate Color
ST80EL-ETN
ST80MEL-ETN
1
DC12V
DC24V
AC110V-220V
0.230A
0.150A
Max. 0.060A
-
R-Red
2
DC12V
DC24V
AC110V-220V
0.260A
0.180A
Max. 0.065A
R-Red
G-Green
3
DC12V
DC24V
AC110V-220V
0.290A
0.205A
Max. 0.075A
R-Red
A-Amber
G-Green
4
DC12V
DC24V
AC110V-220V
0.320A
0.230A
Max. 0.085A
R-Red
A-Amber
G-Green
B-Blue
5
DC12V
DC24V
AC110V-220V
0.350A
0.255A
Max. 0.090A
R-Red
A-Amber
G-Green
B-Blue
W-White
• ST56(M)EL-ETN
Model number Layer Voltage Current Certicate Color
ST56EL-ETN
ST56MEL-ETN
1
DC12V
DC24V
AC110V-220V
0.215A
0.150A
Max. 0.060A
R-Red
2
DC12V
DC24V
AC110V-220V
0.245A
0.170A
Max. 0.065A
R-Red
G-Green
3
DC12V
DC24V
AC110V-220V
0.275A
0.190A
Max. 0.070
R-Red
A-Amber
G-Green
4
DC12V
DC24V
AC110V-220V
0.305A
0.210A
Max. 0.075A
R-Red
A-Amber
G-Green
B-Blue
5
DC12V
DC24V
AC110V-220V
0.335A
0.230A
Max. 0.080A
R-Red
A-Amber
G-Green
B-Blue
W-White
※CE compliant : DC24V, AC110V-220V
• Protection rating : IP23
• Ambient operating temperature : -30°C to + 50°C
• ST45(M)L-ETN
Model number Layer Voltage Current Certicate Color
ST45L-ETN
ST45ML-ETN
1
DC12V
DC24V
AC110V-220V
0.200A
0.135A
Max. 0.053A
-
R-Red
2
DC12V
DC24V
AC110V-220V
0.210A
0.145A
Max. 0.056A
R-Red
G-Green
3
DC12V
DC24V
AC110V-220V
0.220A
0.155A
Max. 0.058A
R-Red
A-Amber
G-Green
4
DC12V
DC24V
AC110V-220V
0.230A
0.165A
Max. 0.061A
R-Red
A-Amber
G-Green
B-Blue
5
DC12V
DC24V
AC110V-220V
0.240A
0.175A
Max. 0.055A
R-Red
A-Amber
G-Green
B-Blue
W-White
Ordering Specications

2 3
Dimensions
(Units : mm)
LAYER
1
2
3
4
5
L
244
284
324
364
404
LAYER
1
2
3
4
5
L
458
498
538
578
618
PCD 30
360˚/3-M4 BOLT
POWER CABLE
Ø8 CABLE ENTRY
Ø45
840
L
196
Ø45
Ø18
RJ45 LAN CONNECTOR
M18 1.5
THREAD
POWER CABLE
L
840
18426200
12
RJ45 LAN CONNECTOR
LAYER
1
2
3
4
5
L
471
511
551
591
631
LAYER
1
2
3
4
5
L
257
322
387
452
517
Ø56
1040
L
207
PCD 40
360˚/3-M4 BOLT
Ø8 CABLE ENTRY
RJ45 LAN CONNECTOR
POWER CABLE
Ø56
Ø18
1040
L
195
26200
RJ45 LAN CONNECTOR
POWER CABLE M18Ⱌ1.5
THREAD
M18Ⱌ1.5
THREAD
12
Ø80
1240
L
178
RJ45 LAN
CONNECTOR
POWER CABLE
RJ45 LAN CONNECTOR
POWER CABLE
PCD 50
360˚/3-M4 BOLT
Ø8 CABLE ENTRY
LAYER
1
2
3
4
5
L
367
407
447
487
527
LAYER
1
2
3
4
5
L
230
270
310
350
390
Ø80
Ø24
12035160
L
40 12
12
ST80EL-ETN
ST56EL-ETN
ST80MEL-ETN
ST56MEL-ETN
ST45ML-ETN ST45L-ETN

4 5
• Connect RJ45 connector that is connected to UTP cable to
Ethernet port of a PC or a router.
• External power line - UL1015 AWG18(0.75sq) x 2C 400mm
• For AC type, power cable is equipped with the product.
• UTP Cable : Category 5 cable
DC/ AC
Power
Fuse
White
Black
RJ45
Wiring Instructions
5. When you unzip “ETN TEST PROGRAM.zip” le, following folders are created.
4. When you unzip the le, there will be a le with the same name below. The instructions are listed inside the le.
Program Sample needed when developing
(x32bit/x64bit compatibility)
Instructions of how to use the product and library le
A program for setting IP before testing the ETN device A program for setting testing the ETN device
PC
RJ45
HUB
EtherNet Tower
VDC 12/24
EtherNet Network
VAC 110V-220V
■ Test Ethernet LED Tower Light
1. Please connect LAN cable of the tower light to the router so that
the tower light can access Ethernet network by referring left
diagram.
2. Please be sure that the power supply shall meet the product
specication accordingly.
Product Installation
Installation wiring instructions
2. Because the ETN tower light is connected to a hub with the PC that is same as the picture on the front page, ETN tower
light and the PC are now connected with the same network.
3. Please download the product manual, library le and test program from Qlight website(www.qlight.com) or blog.qlight.com
1. Please activate default PC network only. Please run Windows CMD(Command line) of PC over the same network in order to conrm
network information where the Ethernet product will be connected.
Example) Windows 7 : Start(Run)->CMD->ipcong /all
Windows 10 : Start menu-> Click right mouse button->CMD->ipcong /all
- Please refer to below network information when the Ethernet product’s network environment is congured.
Applying the Ethernet Device
Ethernet adapter Local Area Connection :
Connection-specific DNS Suffix . :
IP Address. . . . . . . . . . . . : 192.168.10.101
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.10.1

4 5
• Fill TCP/IP and TCP/PORT (①Network Information Setting) with IP address and port that has been setted in ethernet tower light.
• When click LAMP ON, correspond lamp turns on.
• When click LAMP OFF, correspond lamp turns off.
• Please choose appropriate sound pattern group by referring ③ Sound Group Selection area.
• You can choose sound pattern by referring ④ Sound Selection.
• Tower lamp plays sound when SOUND button is pressed.
• Tower lamp stops sound when SOUND OFF button is pressed.
Applying the Ethernet Device
6.
①
-
②
③
④
-
-
Run the “Mac_Setting.exe” program that is inside the IP Set Program Folder .
When the program is running such as the right gure, click the “Mac Find” button in the
“Find Mac Address / Select” section
MAC Address of the connected device appears when you click the Device List combo box.
(If the Mac Addr does not appear, make sure that the connection status or the power supply
is functional and then retry.)
Select the MAC Addr of the device you want to change, and then click on the “Read” button.
Check the information and settings from the “Mac cong status”
Set the value of users network information identied in the previous chapter (subnet mask,
gateway) in each text box, and set a di󰀨erent IP_Addr than your PC
Apply the settings by pressing the Write button
The port is set to “20000“by default and the port number can be changed if necessary
Reconnect After Disconnecting the power from the tower light.
①
②
④
③
7. ETN Test Program Files folder includes the followings.
Test Program Library required for the test program
② Lamp Control
① Network
Information Setting
③
Sound Group Selection
④ Sound Selection
Article Detailed specication
① Network information setting - Input port on TCP/PORT and IP address on TCP/IP that set on Ethernet tower lights
② Lamp control
- ON : Click the button Lamp ON
- ON/OFF : Click the button Lamp Flash
- OFF : Click the button Lamp OFF
③ Sound group selection
- WS : 5 warning sounds(mono)
- WP : 5 special warning sounds(mono)
- WM(1) : 5 Melodies(mono)
- WA(1) : 5 alarms(mono)
- WB : Software Buzzer 5 sounds(speaker type)
- Buzzer : 5 Buzzer sounds
- WM(8) : 5 Melodies(8 chord)
- WA(8) : 5 alarms(8 chord)
④ Sound selection - Select 5 sounds based on model which is xed on Ordering Specications
• User can select appropriate sound pattern by referring Ordering Specifications. There’re WS, WM, and WA sound patterns
and user can choose the option when placing order.
8. Run the “QLight_Lamptest_TCP” program.

6 7
ETN POWER CONNECTOR
Cover(ABS)
Lens(AS)
Housing(ABS)
Pole(Al)
ETN CONNECTOR
ETN CONNECTOR
ETN POWER CONNECTOR
Parts Denition
Buzzer hole
How to Change Lens Kit
• When rearranging or replacing the lens kits, please be aware of the
contact point ①and the connector pin ②marked in the diagram on
the left.
• Press down to assemble the lens kits while making sure that connecto r
pin ②and connector ③aligns correctly.
• Please make sure that the rubber spacer placed on the top of each
lens kit is tightly secured to the bottom of the other lens kit.
※ Caution when lens kit
• Lens kits are connected with connector pins each other. Bad connec-
tion may be experienced when the connector pins are touched with a
foreign substance.
• If the lens kits are not turned on or not ashed after lens kits replace-
ment, please make sure status of lens kit connection.
②
③
①
Mounting Hole Specications
① Machine holes on the mounting surface referring to the diagram below.
② Remove the ange nuts from bolts and place the product through the mounting surface holes.
③ Fasten the ange nuts on the opposite side of the mounting surface until the product is tightened securely.
ST56MEL-ETNST45ML-ETN ST80MEL-ETN
3-Ø5 HOLES
Ø12 CABLE ENTRY Ø12 CABLE ENTRY
3-Ø5 HOLES
PCD 50PCD 40
PCD 30
3-Ø5 HOLES
Ø12 CABLE ENTRY

6 7
Dimensions
ST45ML-ETN
ST56MEL-ETN
TWS45 TWA45
ST80MEL-ETN
TWS80 TWA80
Mounting Accessories (Sold Separately)
• Please refer to the dimensions below for installati on of mounting brackets
■ ST45ML-ETN/ ST56MEL-ETN/ ST80MEL-ETN - Direct Mounting Type Model
Installation Environment and Protection Rating
• This product is designed for use with protection rating of IP23.
• If the product is installed in locations that subject it to excessive dust or water other than the designated IP protection rating
indicated(IP23), it may cause malfunction or damage to the product.
• For further information, please visit our website (www.qlight.com).

8
Ø18
Ø18
32
34 24
Ø70
51
M18x1.5
THREAD
75
52
69
Ø18
Ø18
66
52
38
34
46
50
58
Ø28
1/2" PF
4-Ø5 HOLES
12x22
CABLE ENTRY
Ø70
50
Ø18
4-Ø5 HOLES
PCD 56
60 57
4-Ø5.5 HOLES
Ø19 CABLE ENTRY
Ø18
Ø90
PCD 73
4-Ø5.5 HOLES
2-Ø8.5 HOLES
PCD 54~56
Ø90
Ø18
4-Ø6 HOLES
45.5 66
Ø11 CABLE ENTRY
PCD 73
Ø18
Ø70
51.5 67
4-Ø5.5 HOLES
Ø18 CABLE ENTRY
PCD 54~56
Dimensions
ST45L-ETN
ST56EL-ETN
18mm SCREW & NUT LB18
LW18 SZ18
QZ18 SL18
QL18 QLA18
■ S
T45L-ETN/ ST56EL-ETN - Pole Mounting Type Model

Dimensions
ST80EL-ETN
24mm SCREW & NUT LB24
LW24 SZ24
QZ24 SL24
QL24 QLA24
■ S
T56EL-ETN - Pole Mounting Type Model
46
70
81
32
34
46
M24x1.5
THREAD
2-Ø8.5 HOLES
69.5
52
38
34
46
50
70
1/2" PF
4-Ø5 HOLES
12x22 CABLE ENTRY
33
Ø24
Ø70
55
4-Ø5.5 HOLES
PCD 54~56
Ø24
4-Ø5 HOLES
Ø90
55.5
PCD 73
Ø24
Ø35
Ø24
Ø24
60 57
Ø90
Ø19 CABLE ENTRY
PCD 73
Ø24
4-Ø5.5 HOLES
Ø90
4-Ø6 HOLES
45.5 66
Ø11 CABLE ENTRY
PCD 73
Ø24
Ø90
51.567
4-Ø5.5 HOLES
Ø18 CABLE ENTRY
PCD 71~73
Ø24

ISO International Organization for
Standardization
IECEx
International Explosion
Qlight qualityassurance systemshavebeen
KS Q ISO 9001:2009 regulation.
RoHS2 Restriction of Hazardous
SubstancesDirective
Qlight c omplieswiththe RestrictionofHazardous
Substances Directive by limiting itsuse of hazardous
materials.
KR Korean Register of Shipping
Qlight’s design and qualityassurance system has
CCS
Qlight’s design and qualityassurance system has
ATEX The EuropeanRegulatory
Framework or Manufacture,
Installation andUse of Equip-
ment in ExplosiveAtmospheres
Qlight’sexplosion proof products comply with ATEX
Directives 94/9/EC.
manufactured and manage according to
international standards.
NEPSI National Supervision and Inspection
Center for Explosion Protection
and Safety of Instrumentation
Qlight’s design and manufacturing system
meetsthe People’s RepublicofChina National
explosion proof Standard.
(Chinese Standard-GB3836/GB12476)
KCs Explosion Proof Device
Safety Certification System
The safety performanceofmachines and
Technical capability and production system have
standards.
TIIS Japan Explosion-proof
TIIS is a Japanes explosion proof test and certification
system accordance with the Ministry of Health, Labour
and Welfare Notice and the explosion proof guidelines for
factory electrical equipment. Qlight's explosion proof
products hasve been tested and certified by TIIS.
UL Underwriters Laboratories
Qlight’s design and quality assurance system has
been certified from UL to ensure the stability
of consumption goods and to protect consumers.
CCC
CCCF
Security & Protection
Qlight’s has obtained CCC which guarantees safety,
protection against fraud, environment, etc.
Qlight has passed therigorousexaminationprocess
of "Passing Fire Protection Products Centering" In order
to sell fire-fighting products such as fire alarm equipment
to Chinese market.
CE EuropeanCommission
KC
Commission.
LR Lloyd’s Register
RMRS Russian Maritime
Registerof Shipping
Qlight’sdesign and quality assurancesystemhas
Qlight’s products are certified by KC for preventing
accident caused by fire.
Qlight’s design and quality assurance systemhas
Shipping.
ICAO International Civil Aviation
Organization
Qlight guarantees ourproducts satisfy the criteria
regulated by the International Civil Aviation
Organization(ICAO, FAA).
E-mark Commission Directive
Regarding Vehicle Industry
KCC
Conformity Assessment of Broad-
casting Communication Equipment
Qlight hasobtained EU mark forapprovedvehiclesand
vehicle components sold into theEU(EEA :European
Economic Area)
environment that causes unwanted electromagnetic
waves from thedevice, communication failure due to
other devices or external radiowaves, and malfunction
of the device.
Qlight has been certified to protect the electromagnetic
Technical Certication
• Qlight products are designed to meet strict quality and technical standards. Thus, the Qlight brand is widely recognized for its high quality
and technical innovations from leading institutions around the world.

MEMO

Qlight Co., Ltd. www.qlight.com | [email protected]
Head O󰀩ce | Suite #1510, STX-V Tower, 128 Gasan digital 1-ro, Geumcheon-gu, Seoul, Korea
Tel. [phone](Toll free. [phone]) Fax. [phone]
Factory | 185-25, Mukbang-ro, Sangdong-myeon, Gimhae-si, Gyeongsangnamdo, Korea Tel. [phone](Toll free. [phone])
Qlight OverSEAs Sales Dept | 704 Nakdong-daero, Sasang-gu, Busan, Korea(Eomgung-Dong) Tel : [phone]
Qlight Public Relations & Marketing Team O󰀩ce | 704 Nakdong-daero, Sasang-gu, Busan, Korea(Eomgung-Dong) Tel. [phone]
Qlight USA, Inc. www.qlight.com www.qlightusa.com | [email protected]
3003 North First Street, Suite #341, San Jose, CA 95134 USA Tel. +1 - 408 - 519 - 5740 Fax. +1 - 408 - 519 - 5739
SHANGHAI Qlight Electronic Co., Ltd. www.qlight.com www.qlightcn.com | [email protected]
China Factory/ Shanghai Sales O󰀩ce | #19, Nanda Road, Baoshan Area, Shanghai, China Tel. +86 - 21 - 6651 - 7100 Fax. +86 - 21 - 6315 - 3929
China Factory Site 2 (Qidong) | #33, Haiyan Road, Qidong High-tech Industrial Development Zone, Qidong, Jiangsu Province, China
Tel +86 - 513 - 8384 - 9999 Fax +86 - 513 - 8384 - 9910
Product Operation Inquiry / Customer Support [phone]
You can expect prompt service if you have exact information such as model name, symptom, telephone number and address.
※ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Head office : Suite #1510, STX-V Tower, 128 Gasan digital 1-ro, Geumcheon-gu, Seoul, Korea (Postal Code : 08507)
Factory : 185-25, Mukbang-Ro, Sangdong-Myeon, Gimhae-Si, Gyeongsangnam-Do, Korea (Postal Code : 50805)
For your safety
Specication and dimensions listed in this catalogue subject to change without notice for product quality improvement.
The newest product information is available on our website.(www.qlight.com)
Please read the instruction manual attached to the product carefully before installation and use.
www.qlight.com
EN - ST45ML-ETN - 2106A