quadient IN-360 Series Parts list manual

Machine components:
IN-360 Series Base
Product Replacement Guide Average Time Required: 20 minutes
N1. Remove the components from your original machine
Machine Base
Feed Table Catch Tray Weighing Platform
LAN Cable Power Cable Meter
Ink Cartridge
Remove the Feed Table (b) from the left hand side by lifting the machine (a) slightly
and sliding the Feed Table downwards to unlock, then detach the Catch Tray (c) from
the right hand side
1
6
Disconnect the LAN Cable (e) from the left hand
side by pressing and holding down the clip
Disconnect the Power Cable (f) from the right
hand side of the machine
7
The machine must be disconnected from
the power supply before continuing to
the next step!
Open the door of the Meter compartment
and slide the Meter (h) towards you
8
N2. Unpack your replacement
Remove replacement unit from box. Remove all transit tape
and packaging from replacement machine. Place original unit
back into box ready for collection
1
Caution: Product weighs 9.9kg,
please seek assistance before lifting
Remove the Meter (h)
9
Please do not connect your
replacement machine to the power
until step N6.2
Remove the Weighing Platform (d)
connector from the COM PORT at
the rear of the machine
2
Lift the cover of the machine, Press
down on the Cartridge (g) below the
word ‘TOP’ until you hear a ‘click’
4
Remove the Ink Cartridge (g)
5
Remove tabs from
print heads before
inserting into unit!
Lower Weighing Platform release panel at rear of
the machine. Remove the Weighing Platform (d)
from the top of the machine
3

IN-360 Series Base
Product Replacement Guide - Continued
To finish the replacement process the machine will now need to connect to our server. Please:
N9. Make a connection
2
Press Select ‘ONLINE SERVICES’ & press
Choose ‘GENERIC CALL’ & press
Press when the call has finished
Press key
1
Press Choose ‘AUDIT CALL’
Press and again to confirm
Press when the call has finished
Press key
Congratulations
Your machine is ready to use!
For more information or if you experience
any issues please visit: kb.quadient.co.uk
N3. Insert the Meter
Place the Meter (h) into the
Meter compartment
2
Push backwards until it slots into
position and close the Meter
compartment
3
Lift the cover of the machine to
reveal the Ink Cartridge (g) and
Meter (h) locations
1
1st Inl. Lett
No service
11.02.16
£000.00
00000g
E
S
Mem:
The home screen should be displayed as shown.
If you have departments on your machine you will
need to select a department AND/OR enter your pin
code as necessary
2
N8. Switch on the machine
1
Turn on the machine using
the switch behind the
Power Cable (f)
N6. Connect your Cables
Connect the Weighing Platform (d)
connector to the COM PORT at
the rear of the machine
12
Connect the LAN Cable (e) from the left hand side then connect the Power
Cable (f) from the right hand side of the machine
N7. Attach your Feed Table
Lift machine (a) slightly on the left hand side and align
the hooks to attach the Feed Table (b) – attach the
Catch Tray to the right hand side of the machine (c)
1
N5. Attach Weigh PlatformN4. Install the Cartridge
Insert the Ink Cartridge (g) at an angle
into the machine with the ‘TOP’ and
‘LOCK’ stickers facing upwards
2
Push the Ink Cartridge (g) towards the
back of the machine until you hear a
‘click’ - close the cover of the machine
1
Lower Weighing Platform release panel at rear of
the machine. Place Weighing Platform (d) on top
of the machine and slide forward to lock.
Clip Cable into place on panel and close securely
1
A0087209/B - 26/11/2019