Renz ECO-S User manual

1
“When You Need More Than Staples.”
Toll Free: 800-658-8788
Fax: [phone]
[email protected]
Model ECO-S Binder
2:1 Pitch
Set up
Choose stable surface
Place machine on a stable
surface.
Shelves are not recommended.
Place requirement.
Keep working space free:
Right 8” (20 cm)
Left 6” (15 cm)
Have binding elements
near work area.
Store binding elements in the
special boxes.
Size: 24 x 36 cm
9.5” x 14.2”
Protect sensitive
furniture surface.
The machine stands on soft
plastic feet.
Some surfaces may discolor
after a time.
Operation
Before first use:
Punch scrap paper to clean the
rust preventative from the
punch dies.
Field of application:
Punch:
Paper:
Max 30 pages 20 # stock for
comfortable punching:
15-20 pages
Cardboard
Max thickness 1.5 mm
Plastic Foil
Max 2 pages for 0.3 mm
thickness
Max. binding thickness 28 mm
(1-1/8”)
Approx. 280 pages 20 # stock.
Maintenance
The machine
and the
parts Cleaning:
Wipe with a dry or moist
cloth. Do not use solvents,
sticker may detach.
Empty drawer from
time to time
Pull out drawer at the back
and empty out the paper-
shavings.

2
1
Measure
Determination of the
diameter
Put the back on the edge
against the measuring scale.
Read the diameter of the
binding element (e.g. 3/8”)
2
Adjust
Scale for adjusting the
diameter
Release attachment screw,
determine scale, adjust
diameter, tighten attachment
screw
Adjust distance edge to
according diameter turn
knob
Turn knob index to the according
diameter (e.g. 3/8”) bigger 0 –
bigger edge.
Adjust format 11” Paper
guide right
Pull pins
Screw down the right paper guide,
pull 5 pins from left (21 loops).
Adjust format 8.5” Paper
guide left
Pull pins
Screw down the left
paper guide,
pull 5 pins from left and 5 pins from
the right (16 loops).
3
Insert
Lay binding element in
front of the clamping
fixture
Small loops on top, facing
rear.
Press down clamping fixture
Press back edge and front side will
open.
Push binding element
under the clamping fixture.
Clamping fixture holds binding
element during insertion of the
punched paper.
Release clamping fixture
possibly adjust binding
element vertically.
4
Prepare
The seam of the closed
binding element should
be inside the book
Not outside the covers
Set the book upright,
binding side to the top,
place the back cover in front
The front cover should be behind
the back cover.
Jog the book
Turn the book over, covers
are underneath
Take pages from the top

3
5
Punch
Punch max 30 pages 20#
stock, for comfortable
punching: 15 –20 pages
Punch plastics and thicker covers
separately.
Insert paper into punching
slot, slide the paper against
the paper guide
Adjust 11” format at the right
side, paper must stand evenly, if
not align it again
Adjust 8.5” format at the left
side.
Press punching level
forward until it stops,
then return to original
position.
Hold the machine with the other
hand.
6
Insert
Remove punched paper
from the punching slot. Insert paper onto the binding element
For thicker books, repeat steps five and six until all
pages are punched.
7
Adjust
Press clamping fixture After the paper had been
placed on the binding
element, remove the paper
with the element from the
clamping fixture.
Hold the paper that it does not
slide out of the binding element.
Put binding element under
the closing bar. Binding element must stand vertically at the
back of the closing bar
With opening of the binding
element to the book.
8
Close
Press binding lever
forward until it stops and
back again
For bigger diameters use more
force.
Proper bind Binding under closed:
Adjust closing bar a little
deeper
Release attachment screw and
move it slightly to the left. Fix
attachment screw. Press binding
lever again.
Binding over closed:
Adjust closing bar a litter
higher
Release attachment screw and
move it slightly to the right. Fix
attachment screw. Close next
book.
9
Ready
Turn back cover over Ready

4

5