Saxby Lighting OrionSMART User manual

www.saxbylighting.com
Instruction manual
99055
36W LED module (SMD) RGB
This product is suitable for dimming with ‘TUYA’ app, Amazon Echo or Google Home.
We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the LED’s.
For your safety, always switch off the power supply before changing lightbulbs, or cleaning.
Care and Safety
Technical data
Bulb
Type:
V1 10/09/2021
EU Manufacturer: 1 Gnarrenburg, 27442
UK Manufacturer: BH17 7BY
Conformity with all relevant EC Directive requirements.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities
exist. Check with your Local Authority or local store for recycling advice.
This product is rated at IP65.
IP 65
Conformity with all relevant UKCA Directive requirements.
220-240V~ 50Hz
Supply
Voltage: 24V DC
LED
Voltage: OrionSMART 5M Kit RGB
The power supply is Double Insulated and does not require connection to an Earth circuit.

Warning
Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory
operation of this product. Please retain these instructions for future reference.
Please read these instructions carefully before commencing any work.
This unit must be fitted by a competent and qualified electrician.
Install in accordance with the IEE Wiring regulations and current Building Regulations.
Check the pack and make sure you have all the parts listed.
To prevent electrocution switch off at the mains supply before installing or maintaining this fitting. Ensure other persons cannot
restore the electrical supply without your knowledge. If you are in any doubt, please consult a qualified electrician.
If replacing an existing fitting, make a careful note of the connections.
The mains plug must be situated indoors (e.g. house, garage, shed) in order to protect it from the elements.
This system operates at Safety Extra Low Voltage (24V d.c.), via a LED drive. Never connect the LED strips
directly to the mains without using the correct LED driver.
Do not exceed the LED driver load. LED drivers may require a minimum load to operate.
Always unplug the LED driver from the mains when installing or maintaining this system.
This product contains non-replacable parts and cannot be serviced. If damage occurs the part should be scrapped.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with
your local authority or retailer for recycling advice.
Layout
This product is suitable for dimming with ‘Tuya’ app, Amazon Echo or Google Home.
We recommend putting the wifi receiver within 20-25 meters of your WI-FI Hub. This will vary depending on the
strength of your WI-FI coverage.
We recommend testing the position before full installation.
Installation
The LED strips are Safety Extra Low Voltage and must not be earthed.
Choose a dry, clean and smooth surface. Position the UK plug driver, TUYA controller controller next to the mains outlet socket
that the system will connect to. Do not plug-in at this stage.
After deciding the layout of the LED strips, ensure the cables are long enough to connect to the desired positions.
The Flexiline LEDs are mounted on a sticky tape which can be stuck to most surfaces.
The Flexiline LEDs can be shortened to a minimum of 100mm or multiples of 100mm.
Cables in walls must be protected using suitable conduit or plastic trunking.
Avoid locating any cables in positions that would cause a hazard. Position cables and Flexiline LEDs
away from areas where they may be at risk from being cut, trapped or damaged.
Plan the desired layout of this fitting carefully, ensuring the cables will reach the distance between the power
supply and the Flexiline LEDs.
The power supply is Double Insulated and does not require connection to an Earth circuit.
This is a self contained kit and cannot be extended.
1) Connect the LED strip to TUYA controller
Warm the tape with a hair dryer
when it’s below -10ºC - -50ºC
Strip off the protective film
(Notice: Do not peel off the tape under the film)
Stick the LED strip and press over it,
use self-adhesive buckles as needed
Cut the LED strip along the black cutting
line, or soldering point
2) Connect the TUYA controller connected
the LED strip to the UK plug driver
3) Plug the driver to household outlet
make sure the arrows
are facing each other
on same one side
×
2
3
2
1
white color UK plug Drive, DC24V, 1A, 24W,
White color 22AWG,
1.5Meter length,
TUYA controller
female 4Pin 24AWG
150mm cable
male 4Pin 24AWG
170mm cable