Schuchmann MADITA MAXI User manual

Instructions for use.
madita maxi. The proven, solid therapy chair.
madita maxi.

Many thanks.
Dear Customer
At this point we would like to thank you for placing your trust in our company and
for purchasing our product. We ask you to read through the Instructions for use carefully
prior to initial commissioning of the product, and to observe them. Please note that
guidelines and representations in these Instructions for use may deviate from your
product due to diering equipment. We reserve the right to make technical modifications.
Important information!
Ensure that these Instructions for use remain with the product.
Your schuchmann Team

03 Contents.
1. Preparation. ................................................................................ 05
1.1 Delivery............................................................................................................................05
1.2 Safety measures prior to use ..............................................................................05
1.3 Safe disposal...............................................................................................................05
1.3.1 Packaging...........................................................................................................05
1.3.2 Product................................................................................................................05
1.4 Where to store the Instructions for use..........................................................05
2. Product description. .................................................................... 06
2.1 Material information ................................................................................................06
2.2 Handling/transport................................................................................................06
2.3 Application areas, use according to the intended purpose .............06
2.3.1 Indications .........................................................................................................06
2.3.2 Contraindications .........................................................................................06
2.4 Use not in accordance with the intended purpose / warning gui-
delines............................................................................................................................07
2.5 Equipment for basic model................................................................................. 07
2.6 List of accessories....................................................................................................08
2.7 Product overview......................................................................................................08
3. Settings. ..................................................................................... 09
3.1 Castors ...........................................................................................................................09
3.2 Seat angle...................................................................................................................09
3.3 Seat height...................................................................................................................10
3.4 Back angle...................................................................................................................10
3.5 Seat depth.................................................................................................................... 11
3.6 Back height................................................................................................................... 11
3.7 Armrests........................................................................................................................... 11
4. Accessories. ................................................................................ 12
4.1 Headrest......................................................................................................................... 12
4.2 Thorax pelotte pads................................................................................................ 12
4.3 Thigh guide .................................................................................................................. 12
4.4 Parking brake.............................................................................................................. 12
4.5 Footrest.......................................................................................................................... 13
4.6 Plug-in foot support................................................................................................ 13
4.7 Wooden therapy table........................................................................................... 13
4.8 Knee abduction wedge.........................................................................................13
4.9 Wheel base extension ............................................................................................14
5. Cleaning and servicing. ............................................................... 14
5.1 Cleaning and disinfecting .....................................................................................14
5.1.1 Cleaning ...............................................................................................................14
5.1.2 Disinfection.........................................................................................................14

04
5.2 Servicing ........................................................................................................................ 15
5.3 Maintenance ............................................................................................................... 15
5.3.1 Maintenance specifications ...................................................................... 15
5.3.2 Maintenance plan.......................................................................................... 16
5.4 Spare parts .................................................................................................................. 16
5.5 Duration of use and re-use.................................................................................. 16
6 . Technical data. ........................................................................... 18
7. Guarantee. .................................................................................. 18
8. Identication. ............................................................................. 19
8.1 EU Declaration of Conformity.............................................................................. 19
8.2 Serial number / date of manufacture...........................................................20
8.3 Product version .........................................................................................................20
8.4 Issue of the document ..........................................................................................20
8.5 Name and address of the manufacturer, specialist dealer sup-
plying the product...................................................................................................20
Contents.
04

05 1. Preparation.
1.1 Delivery
On receiving the product, please check it for completeness, lack of faults
and any transport damage. Inspect the goods in the presence of your
forwarder. Should transport damage have occurred, please arrange for
an inventory (determination of the faults) to be made in the presence of
the forwarder. Please send a complaint in writing to the specialist dealer
responsible.
1.2 Safety measures prior to use
The correct use of the product requires a detailed and careful instruction
of the user or the accompanying person. We ask you to read through the
Instructions for use carefully prior to initial commissioning of the product,
and to observe them. It is possible that product parts that get in contact
with the skin may heat up in the sun. Cover these areas or protect the de-
vice from direct sunlight.
1.3 Safe disposal
In order to preserve and protect the environment, to prevent environmental
pollution and to improve the recycling of raw materials, please note the
disposal instructions in points 1.3.1 and 1.3.2.
1.3.1 Packaging
The packaging of the product should be kept for any future transport that
might be required. Should you have to return the product for repairs or in
case of a guarantee claim, please if possible use the original box so that
the product is optimally packaged. Otherwise, separate the packaging
materials for recycling according to their classification.
Do not leave packaging materials unattended, as they are a possible source of
danger.
1.3.2 Product
Attheendoftheproductlifecycle,recycletherawmaterialsusedintheproduct
according to their nature (see material information under point 2.1).
1.4 Where to store the Instructions for use
Please store these Instructions for use carefully and ensure that these
Instructions for use remain with the product in case of re-use. Should you
lose the instructions, you can always download an updated version at
www.schuchmann.de .

06 2. Product description.
2.1 Material information
The base frame and the individual elements are made of steel and alumi-
nium which are non-corroding and powder-coated. The covers are made
of 100% polyester and are flame resistant (according to DIN EN 1021-1+2).
2.2 Handling / transport
The therapy chair is not designed to be carried, as it is fitted with castors.
Should you have to carry the equipment due to obstacles, ensure that
all moving parts are tightened. Then position yourself next to the therapy
chair, grip it at the front and rear under the seat unit and carry it to the
required location. To transport the therapy chair, reduce all adjustments to
their most compact size (fold up foot support, set lowest seat height etc.)
2.3 Application areas, use according to the intended purpose
The madita maxi. therapy chair is a medical product of risk class 1 and de-
signed for use at home and at school. It can be used for all age groups.
Individually adjustable seat dimensions and supporting pelotte pads allow
a stable and upright sitting position. Any other use or use over and abo-
ve this purpose shall be considered not in accordance with the intended
purpose.
2.3.1 Indications
The madita maxi. therapy chair is designed for users who cannot sit or
stand unaided, however whose limited torso posture does not permanent-
ly require sitting in a seat pan. This includes impaired sitting with functional
and/or structural damage to the torso or the torso and, if applicable, the
cervical muscles (e.g. due to neurological/neuromuscular disorders, defor-
mations of the spine) with poor posture.
2.3.2 Contraindications
In general, the indication should be accompanied by a doctor/ortho-
paedist. It should therefore be clarified prior to procurement whether
contraindications exist for the patient. In general, any type of pain repre-
sents a contraindication.

07 2. Product description.
2.4 Use not in accordance with the intended purpose / warning guide-
lines
• Make sure that the therapy chair is used by one user only.
• Only use the therapy chair on an even and solid surface.
• Do not use the therapy chair to transport people.
• In order to guarantee safe lifting when transporting the therapy chair,
stand at the side of the therapy chair and grasp the front and back of
the seat surface. Here all movable parts should be tightened, e.g. seat
depth adjustment.
• Never leave the user seated in the therapy chair without supervision.
• Correct usage of the therapy chair requires precise and careful training
of the accompanying person.
• The max. load (see Point 5) may not be exceeded.
• Do not use the therapy chair if it has defective, worn or missing parts.
• For reasons of fire safety, the therapy chair may not be placed close to
an open fire or any other strong source of heat such as electric or
gas heaters.
• Use only accessories and spare parts made by Schuchmann, otherwise
you will compromise the safety of the user.
• Only use the therapy chair if all components have been correctly
mounted and adjusted.
• Please ensure that none of the user's extremities are in the respective
area when making adjustments of any kind to minimise the risk of injury.
• Please read out the Instructions for use for users suering from a visual
or reading impairment, so that they can use the therapy chair safely.
2.5 Equipment for basic model
• Anatomically moulded seat pad with cover
• Seat height can be adjusted with a crank, seat angle adjustment by
means of two gas pressure springs at 200N each, operated by
foot pedal
• incl. push handle and armrests with extra wide support that can be
adjusted in width, height and angle
• 4 double castors (100 mm), 2 of which with locking device
• Frame colour: metallic anthracite

08 2. Product description.
2.6 List of accessories
• Standard headrest - padded, height-adjustable
• Headrest with side guidance - padded, adjustable in height and angle
• Headrest in shell shape - padded, adjustable in height and angle
• Reinforced thorax pelotte pads
• Thigh guide
• Knee abduction wedge
• Central locking brake on the rear castors
• Wooden therapy table
• Incontinence coating in the seat area
• Wheel base extension
• Wooden foot support
• Plug-in foot support
• Positioning aids
2.7 Product overview
Headrest
Dual castors
Push handle
Back angle adjustment
Thorax pelotte pads
Plug-in
foot support
Back
Armrests
Thigh guide
Seat pad
Base frame
Foot pedal for
height adjustment

09 3. Settings.
Settings and adjustments to the product or accessories may only be made
by people who have been given the necessary instructions by a medical
product advisor. Please ensure that none of the user's extremities are in
the respective area when making adjustments of any kind to minimise the
risk of injury.
3.1 Castors
The therapy chair should always be pre-
vented from rolling away inadvertently th-
rough braking of the 2 rear castors. To do
this, press down the locking device (A) on
each castor using the tip of your foot (B).
To release the castors again again, push
the locking devices up again with the tip
of your foot (C).
The brakes only work reliably on an even
surface!
3.2 Seat angle
The seat angle adjustment is supported
by two gas pressure springs. Operate the
foot pedal (D) to adjust the seat ang-
le. Using light pressure, the seat can be
moved to the active or passive position.
The foot pedal (D) can be secured with
the spring pin (to be found on the inside
of the foot pedal) against unintentional
operation. To do this, turn the spring pin
until it engages. If necessary, assist en-
gagement by moving the foot pedal
gently. The locking eect is cancelled by
pulling out the spring pin and turning it a
quarter turn.
A
D
B
C

10 3. Settings.
3.3 Seat height
madita maxi. can be adjusted in height up
to 12 cm. The seating aid is delivered lo-
west setting. In order to change the seat
height, turn the crank (A) below the base
frame.
In addition, the two attached gas pres-
sure springs must be readjusted. This is
done by removing the screws at the lo-
wer end of the two gas pressure springs
within the hole pattern (B).
This adjustment should only be made by a
specialist dealer!
3.4 Back angle
The backrest angle can be adjusted by
operating the clamping lever (C) on the
right side of the seating aid.
Please tighten the clamping lever again
after each adjustment!
The backrest angle can also be ad-
justed for high loads. To do this, bring
the screws (D) on both sides into the
desired position in the hole.
A
B
D
C

11 3. Settings.
3.5 Seat depth
The seat depth can be adjusted by loo-
sening the two grub screws (A) on both
sides of the chair.
Please tighten the grub screws again after
the adjustment!
3.6 Back height
In order to change the backrest height,
the two twist grips (B) on the rear of the
backrest must be released.
Please tighten the twist grips again after the
adjustment!
3.7 Armrests
The angle, height and width of the arm-
rests can be adjusted.
Loosen the twist grip (C) on the side of
the armrest to adjust the angle. Bring
the armrest into the desired position and
tighten again the twist grip. Release the
twist grip (D) on the side of the armrest
to adjust the height. Bring the armrest
into the desired position and tighten the
twist grip again. Undo the grub screw (E)
below the seat for the width adjustment.
Bring the armrest into the desired positi-
on and tighten the grub screw again.
Please tighten all screw connections after
each adjustment.
A
B
C
D
E

12 4. Accessories.
4.1 Headrest
The height of the headrest can be ad-
justed. Undo all four nuts (A) at the rear
to bring the headset into the desired po-
sition.
Please tighten again the nuts after each ad-
justment!
4.2 Thorax pelotte pads
The thorax pelotte pads can be adjusted
in height and width. Undo the screws (B)
at the rear of the backrest and bring the
thorax pelotte pads into the desired po-
sition.
Please tighten again the screws after each
adjustment!
4.3 Thigh guide
The thigh guide pads are individually
adjustable in height and depth. To ad-
just the width, undo the two hexagon
socket screws (C) below the seat surface
and bring the thigh guide pads into the
desired position. In order to adjust the
depth, please open the zips (D), loosen
the 3 pan head screws (E) with a hexa-
gonal wrench and bring the pad into the
required position. Additionally, you can
adjust the depth of the entire thigh guide
via the hole pattern (F) by loosening and
repositioning the screws (C). Three posi-
tions are possible here.
After each adjustment, please retighten all screw connections!
4.4 Parking brake
The parking brake can be used by the user themselves. If the lever moun-
ted onto the seat system is pressed down, then the brake is released. If the
lever is pointing upwards, the brake is applied.
A
B
C
D
E
F
C

13 4. Accessories.
4.5 Footrest
The knee angle adjustment has a snap-on
connection that allows adjustments in small
steps. To do this, you must release the twist
grips (A) on both sides. Subsequently, undo
the grub screws (B) on the rear of the footrest
to adjust the height.
After each adjustment, please retighten the
screw connections!
4.6 Plug-in foot support
The plug-in foot support is easy to mount
and guarantees comfortable sitting. Simply
pull both lock bolts (C) to remove the foot
support. When positioning the foot support,
first insert the rear connection (D) into the
base frame and ensure that the locking bolts
(C) engage.
4.7 Wooden therapy table
Insert the therapy table on the left side into
the adapter (E) next to the armrest and
tighten the wing screws (F). The height can
be changed by adjusting the armrests (see
Point 3.7). In order to fold the therapy table
to the side, e.g. when the user wants to sit
down or get up, loosen the wing screw (F),
swivel the table upwards and guide it at to
the side of the therapy chair.
4.8 Knee abduction wedge
Loosen the wing screw (G) to adjust the
height of the knee abduction wedge. To ad-
just the depth, loosen the wing screw (H) be-
low the seat surface.
Please tighten the screw connections again
after each adjustment!
A
B
D
C
C
C
F
G
H

14 4. Accessories.
4.9 Wheel base extension
The wheel base extension is used to guarantee
stability even for larger seating systems when
the seat is inclined backwards.
The wheel base extension cannot be adjusted!
5. Cleaning and servicing.
5.1 Cleaning and disinfecting
5.1.1 Cleaning
Please clean all frame elements regularly with a spon-
ge or damp cloth; making sure that water droplets are
removed. Please clean with a mild household deter-
gent for severer dirt. Thorough drying of the cleaned
areas is important.
All fabrics that cannot be removed can be wiped with
a moist cloth. For all removable fabrics please pay at-
tention to the sewn-in care labels (such as A+ B) on the
respective element.
Please also pay attention to our general clea-
ning and hygiene advice. This can be found at
www.schuchmann.de/mediathek.
5.1.2 Disinfection
Various products can be used for surface disinfection of metal and plastic
parts.
Liquid disinfectants are available as ready-to-use solutions that are spray-
ed on and evenly applied with a soft cloth. Alternatively, wipes pre-soaked
with disinfectant can be used to wipe the products over the entire surface.
In both cases, care must be taken to ensure complete wetting. Disinfection
in fully automatic disinfection systems is also possible and recommended.
The exposure times may vary and can be found in the manufacturer's ins-
tructions for the products used.
7190045
A
Obermaterial/
top cloth/dessus:
100% Polyester
b

15
5.2 Servicing
Please carry out a visual inspection on a daily basis and regularly check
the product for cracks, breaks, missing parts and malfunctions. In case of a
defect or malfunction, please contact the specialist dealer who supplied
you with the product (see Point 8.5).
5.3 Maintenance
For reasons of user safety and to retain product liability, the product must
be subjected to maintenance by a specialist dealer at least once a year
(see Point 8.5). The maintenance work carried out must be documented in
the maintenance plan (see Point 5.3.2).
5.3.1 Maintenance specications
• Basic cleaning according to manufacturer instructions (see Point 5.1.1)
• If necessary, disinfection according to manufacturer instructions (see
Point 5.1.2)
• Damages to the frame, mounting parts and accessories (cracks, breaks,
corrosion, bent or missing parts)
• Strength of the connections (tighten loose screws, replace
missing screws)
• Functionality of the adjustment elements (screws, release lever,
foot pedal)
• Functionality of other adjustment elements (back, headrest, pelotte
pads, armrests, footrests, table and guides in the leg area)
• Functionality of the gas pressure springs (if necessary readjustment of
the bowden cables)
• Functionality of the safety elements (anti-tilt)
• Correct mounting of the seat unit
• Functionality of brakes
• Functionality of the rollers (concentricity, smooth running)
• Check the harness for damage (clamping device, closures, seams)
• Check the pads and covers for damage
• Legibility of the type label
• Final complete functional check of the aid
• Check that all mounting parts and associated accessories are
correctly fastened
5. Cleaning and servicing.

16 5. Cleaning and servicing.
5.3.2 Maintenance plan
Maintenance specifications of the manufacturer (see Point 5.3.1) were car-
ried out:
Date Company Name signature
Any defects or damage found must be repaired by the specialist dealer or the
manufacturer before reuse.
5.4 Spare parts
Use only original accessories and original spare parts from Schuchmann,
as otherwise the safety of the user is endangered and the warranty expires.
To order spare parts, please contact the supplying specialist dealer
(see point 8.5) stating the serial number of the product. Necessary spare
parts and accessories must only be installed by trained personnel.
5.5 Duration of use and re-use
The expected duration of use of our product, dependent on the usage in-
tensity and amount of re-use, totals up to "8" years if the usage takes place
in accordance with the information in these Instructions for use. It may be
possible to use the product over and above this time period if it is in a
safe condition. The expected duration of use does not refer to wear parts,
such as for example wheels, gas pressure springs,... . The maintenance and
evaluation of the condition, and if applicable the potential for re-use, must
be decided by the specialist dealer.

17 5. Cleaning and servicing.
The product is suited for re-use. Prior to forwarding, please follow the clea-
ning and disinfection instructions stated in Point 5.1. Accompanying docu-
ments such as these Instructions for use are part of the product and must
be passed on to the new user. No disassembly is required prior to re-use. In
the case of storage, it is recommended to fold the product to the smallest
dimension to save space.
Should a serious incident occur during the service life of the product despite
being used as intended
, this must be reported immediately to the manufactu-
rer and the competent authority.

18 3. Settings. 18 6 . Technical data.
Dimensions
Dimensions
ASeat depth 36 - 47 cm
bSeat width 34 - 44 cm
C* Height short back 40 cm
C* Height long back 48 cm
C** Height short back 48 cm
C** Height long back 56 cm
ESeat height 48 - 60 cm
FLower leg length 18 - 45 cm
GTotal width 64 cm
HLength of base frame 80 cm
Seat angle (-) 5° - 30°
Back angle (-) 5° - 25°
max. load 120 kg
Weight 26 kg
* from 3 mm aluminium sheet | **from 4 mm aluminium sheet
The two-year statutory guarantee period shall apply for all products. This
begins with the delivery or handover of the goods. Should a verifiable ma-
terial or manufacturing fault occur within this time period, we shall, after
carriage paid return to us, view the indicated damage and, if applicable,
either repair or deliver a new product at our discretion.
7. Guarantee.

1919 8. Identication.
8.1 EU Declaration of Conformity
EU Konformitätserklärung
EU Declaration of Conformity
Firma / Company Schuchmann GmbH & Co. KG
Rudolf-Runge-Str. 3 · 49143 Bissendorf · Deutschland / Germany
Tel. [phone] / 40 71 00 · Fax [phone]
erklärt in alleiniger Verantwortung, dass das nachfolgend genannte Produkt der Risikoklasse 1
declares under our sole responsibility that the following product(s) of Class 1 Medical Devices
Datei: Konformitätserklärung madita maxi Stand: Rev. 2.0 Seite: 1
„madita maxi.“Therapiestuhl / therapy chair
Art.-Nr. / Item-No.: 30 03 000
Basis UDI-DI /
Basic UDI-DI: 4251040200004000300XXXX8D
den einschlägigen Bestimmungen der im folgenden aufgeführten Richtlinien und Standards entspricht:
is / are in conformity with the requirements of the below listed directives and standards:
Verordnung (EU) 2017/745 über Medizinprodukte vom 05. April 2017
Regulation (EU) 2017/745 on medical devices of 5 April 2017
DIN EN 12182:2012 Technische Hilfen für behinderte Menschen
Technical aids for disabled persons
DIN EN ISO 14971:2013 Medizinprodukte - Anwendung des Risikomanagements auf Medizinprodukte
Medical devices - Application of risk management to medical devices
Diese Konformitätserklärung gilt nur für Produkte mit den oben genannten Artikelnummern und
ist gültig bis zum 31.12.2023.
This declaration of conformity applies only for products with above-named Item-numbers
and is valid until 31.12.2023.
Datum / Date: 01.04.2020
Unterschrift /
Sign:
Name /
Name: Torsten Schuchmann
Funktion /
Function: Sicherheitsbeauftragter für Medizinprodukte / Safety officer for medical devices

20
8.2 Serial number / date of manufacture
The serial number, the date of manufacture and other information can be
found on the type plate, which is located on all of our products (A).
8.3 Product version
The madita maxi. therapy chair is available in one size and can be supple-
mented through a diverse range of accessories (see Point 4).
8.4 Issue of the document
Instructions for use madita maxi. - Change status G; issue 11.2020
8.5 Name and address of the manufacturer, specialist dealer supplying
the product
This product was manufactured by:
8. Identication.
This product has been delivered by the following specialist dealer:
Schuchmann GmbH & Co. KG
Rudolf-Runge-Str. 3 · 49143 Bissendorf · Germany
Phone [phone] / 40 71 00 · Fax [phone]
[e-mail] · www.schuchmann.de
A
Product name
Item number
Serial number
schuchmann.de • [e-mail] • Fon +49 (0) 5402 / 40 71 00
Rudolf-Runge-Str. 3 • 49143 Bissendorf • Germany
Barcode UDI-DI Barcode UDI-PI
UDI-DI
SN / UDI-PI
Type
Product
Max. load
Size
MD
Size
max. load
Date of manufacture
Product labelling in accordance with MDR
GA 30MA - EN_1.1