SEA PRE-GATE User manual

PRE-GATE
CONTROL UNIT
web site: www.sea-usa.com
e-mail: [email protected]
REV 07 - 09/2010
International registered trademark n. 2.777.971
SEA USA Inc.
10850 N.W. 21st unit 160 DORAL MIAMI
Florida (FL) 33172
Phone:++1-305.594.1151 Fax: ++1-305.594.7325
Toll Free: 800.689.4716
67411095

SAFETY INSTRUCTIONS ..........................................................................................................................3
PARTS SPECIFICATIONS..........................................................................................................................5
CONNECTIONS..........................................................................................................................................6
...........................8
MOTOR 115V, LIMIT SWITCH, ENCODER................................................................................................9
SAFETY LOOP, CENTRAL LOOP, EXIT LOOP........................................................................................10
POWER SUPPLY, WARNING LAMP, COURTESY LIGHT.......................................................................11
MAGNETIC LOCK, SOLENOID LOCK, INTRUSION CONTACT, BUZZER.............................................12
BATTERIES, 24Vdc MOTORS..................................................................................................................13
OPENING/CLOSING, KEY BUTTON ENABLE, CARD READER, FIRE SWITCH...................................14
PHOTOCELLS, SAFETY EDGE, MASTER / SLAVE CONNECTIONS....................................................15
........................................................................................................................................16
.................................................................................................18
TRIMMER REGULATION, SELFLEARNING PROCEDURE, MOTOR CONNECTIONS
DIP SWITCHES
SALES CONDITIONS AND WARRANTY
TABLE OF CONTENTS
2
PRE-GATE
Opening
Electronic Systems
International registered trademark n. 2.777.971
REV 07 - 09/201067411095

WARNING: Not following these instructions may
cause severe injury or death to person
END USER ISTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
WARNING-Toreduceriskofsevereinjuryordeath:
1)READANDFOLLOWALLINSTRUCTIONS
2) Never let children operate or play with door controls. Keep the remote control away
fromchildren.
3)Always keep the moving system in sight and away from people and objects until it is
completely closedor stopped. NO ONE SHOULD CROSS THE PATH OF THE
MOVINGSYSTEM.
4) Test the system gate operator monthly. The system MUSTreverse on contact with a
rigidobjectorwhenanobjectactivatesthenon-contactsensors.Toobtainareverseon
contact with an object on hydraulic linear and in-ground operators SEArecommend to
installthepatentedsafetydevice“SAFETYGATE”foreachleaf.
After adjusting the force or the limit of the travel, retest the gate operator. Failure to
adjust properly the gate operator properly can increases the risk of severe injury or
death.
5)Usethemanualreleaseonlywhengateisnotmoving
6) KEEP GATES PROPERLY BALANCEDAND MAINTAINED.An improper balancing
or maintenance increases the risk of severe injury or death. Have a qualified service
personaltomakerepairstocables,springassembliesandotherhardware.
7)Theentrancewithagateoperatorssystemisforvehiclesonly.PedestrianMUSTuse
separateentrance.
8) Every gate operator installation MUST have secondary protection devices against
entrapment, such as edge sensors and photo beams more in particularly in places
wheretheriskofentrapmentismorelikelytooccure.
SAVE THESE INSTRUCTIONS
The installer is responsible for grounding the operator system,
forprovidingthemainpowerbreakerswitch,andformakingsure
thattheentiregatesystemsmeetsallapplicableelectricalcodes.
3
PRE-GATE
International registered trademark n. 2.777.971
REV 07 - 09/201067411095

GROUNDING
Goodgroundingandpropersurgesuppressionareanintegralpartofproperinstallationfor
a gate operator system. One or all of the following may require surge suppressors: high
voltagepowerlines,lowvoltagepowerlines,telephonelines,datalines,lowvoltagecontrol
lines and loops. How much surge suppression is required depends upon how susceptible
the area is to lightning and power surges. Regardless, good grounding is essential. To
realizemaximumprotection,propergroundingandpropersurge suppressionisabsolutely
necessary.
If the circuit breaker box is located close to the gate operator system, for example, in a
guard house, then the ground from that circuit can be used to ground the gate operator
system.Eliminateall90°bendsingroundwiresandkeepaminimumofthreefeetbetween
thesurgesuppressorandtheequipmentbeingprotected.
Ifthepowersourceorcircuitbreakerboxisnotlocatedclosetothegateoperatorsysteman
Isolated Ground Zone (IGZ) needs to be created. An IGZ can also be created if the circuit
breaker box is located close by the gate operator system. An IGZ is an imaginary circle
drawn around the gate operator system. The gate operator system not only includes the
gateoperatorsandcontrolpanel,butalloftheaccessoriesanddevicesassociatedwithitat
that controlled entry point. This includes loop detectors, card readers, digital entries,
telephone entries, any device that has a ground or requires a ground and ali of the surge
suppressors. The ground bus is a common ground point calied a Single Point Ground
(SPG). It is used to bond all the equipment and device grounds in the IGZ together. The
SPG is very important because it helps eliminate different ground potentials that can be
present on the equipment. In such cases, equipment damage occurs even with surge
suppressors.
Do not use or connect the ground wire coming from the circuit breaker box. By using an
Isolated Ground Zone, you are separating the gate operator system from the house or
building ground. This eliminates ground potentials. It is recommended that the ground bus
be located in a separate NEMAtype enclosure.All grounds will be tied to this ground bus.
Somepointstoremember:
Keep all ground wires as straight as possible. Do not have any sharp 90° bends. Have a
minimum of 3 feet of wire between the surge suppressor and the equipment being
protected.
Equipment ground wire should be a minimum of 12AWG. The main ground wire from the
bus bar to the ground rod shouid be an 8 or 6AWG copper wire. Ground rod should be a
minimumof10feetinlength,longerdependingonlocalsoilconditions.
For more information regarding good grounding practices check: National Electric Code
art. 250; IEEE Emerald Book, standard 100; International Association of Electric
Inspectors.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
4
PRE-GATE
International registered trademark n. 2.777.971
REV 07 - 09/201067411095

PARTS SPECIFICATION
L1 = Led access limit switch gate closed
L2 = Led access limit switch gate open
L3 = Led access photocells (n.c.)
L4 = Led access border
L5 = Led module safe loop
L6 = Led module centre loop
L7 = Led module exit loop
L8 = Led access receiver pedestrian
L9 = Led access push button open
L10 = Led access push button stop
L11 = Led access push button close
L12 = Led access card
L13 = Led access fire
L14 = Led access exit loop
L15 = Led access safe loop
L16 = Led access receiver start
L17 = Led exit TX serial
L18 = Led access RX serial
CN1 = Safety loop connector
CN2 = Central loop connector
CN3 = Free Exit loop connector
M1 = Motor connector
M2 = Loop connector
M3 = Power line (hight voltage) connector
M4 = Service lamp connector
M5 = Alarm and Lock connector
M6 = Backup unit connector
M7 = Master/Slave connector
M8 = Plug-in radio receiver connector
M9 = Input connector
DS1 = Dip-switch
DS2 = Dip-switch
F1 = Master fuse
J1 = Keep/not Keep alarm
T1 = Transformer
TR = Trimmers
M1
MAX TORQUE
TIMER
REVERSE SENS
AUX_POW_SUP
24VDC
COMMON
START
COMMON
PARTIAL START
M8-1
M8-5
M3M4M5M6
M9
M8
M7
OPEN STOP CLOSE
FREE EXIT
CENTRALSAFETY
1 2 3 4 5 6 7 8
1 2 3
RESET ALL.
KEEP ALARM
NOT KEEP ALARM
F1
J1
CN1
CN3
CN2
DS1
DS2
M2
L12
L13
L14
L15
L16
L8
L9
L10
L11
L5 L6 L7
L3
L4
L2
L1
T1
L18
L17
TR
5
PRE-GATE
International registered trademark n. 2.777.971
REV 07 - 09/201067411095

M1
1 2 3 4 5 6 7 8 9 10
tr
Neu al
i s os
Lim t witch cl ing
m tch ope
Li it swi ning
Cosel / Open
CONNECTIONS
M2
1 2 3 4 5 6
o
Safety L op
M3
1 2
Lne 5 ai 11 V c
M4
1 2 3 4 5
M5
1 2 3 4 5 6 7 8 9 10
Mag / Sol Lo O
ck N
Cmmo
o n
M6
1 2 3 4 5
ommonC motor
Open / Close
Encod r dat
e a
mmoCo n
Encod er sup y
er pow pl
t l LoCen ra op
F e t L pre Exi oo
2 2 21 1 1
a c
Ph se 115Va
ni g la pWar n m
15V1
tNo used
Courtesy light
115V
Bat e cha ge
t ry r r
t e a eBa t ry ch rg r
r gh
Moto 24V ri t
Mot 24V left
or
Mag / Sol Lock NC
ag / l Lock C
M So om
In ru o co tt si n n .
a co
Al rm nt.
2 21 1
tAlarm rese
Aux. power pply 24VDsu C
M
N t seo u d
Nt se
o u d
6
PRE-GATE
International registered trademark n. 2.777.971
REV 07 - 09/201067411095

Inversion/lock with photocell or safeloop
Opening direction
Card slave
Preblink
Self learning
1122334455667788
ONON
ON= Function Active
DS1
M9
1 2 3 4 5 6 7 8 9 10 1112 13 14 15
dSe ur ty ge
c i e
Photo ll
ce
Encoder
CONNECTIONS
M7
1 2 3
Ma t r / Sla A
s e ve
Soft start
11223344
ONON
ON= Function Active
DS2
Free
t / Sl BMas er ave
t SMa r / lave GND
s e
Op ne
mmoCo n
pS t o
sClo e
K bot on enabley t e
Crda
i
Fire sw tch
Cmmoo n
Eternal Loox p
Ext. afety LoopS
Cmmo
o n
oc er cPhot ell pow supply 24Vd
m
Co mon
Type of closing
Type of photocell
Functioning master card
Autotest Photocell
7
PRE-GATE
International registered trademark n. 2.777.971
REV 07 - 09/201067411095

- Bridgethephotocell(ifDS1-2is to OFFposition),thesafetyedgeandSTOPiftheyarenotconnected.
- IftheencoderisusedputDIP4ofDS1onON
- Releasetheoperatorandclosethegatemanually(limitswitchofclosingoccupied)
- Reactivatethemechanicalblock
- PutDip8on“ON”andpressthepushbuttonOPENorSTART
- Waitforthecompleteopeningofthegateandreposition DIP8onOFF.
SELFLEARNING PROCEDURE
MAX TORQUE
TIMER
REVERSE SENS
AUX_POW_SUP
24VDC
COMMON
START
COMMON
PARTIALSTART
M8-1
M8-5
OPEN STOP CLOSE
CENTRAL
SAFETY
1 2 3 4 5 6 7 8
1 2 3
RESET ALL.
KEEPALARM
NOT KEEP ALARM
TRIMMER REGULATION
1
TR
2
3
1.
2.TrimmerREVERSESENSE
TrimmerTIMER
TrimmerMAXTORQUE
Thistrimmerisusedtoadjustthemotortorque.Thisadjustmentis
essentialforoperatorswithoutmechanical or hydraulic anti-crush
devicesandmustbecarriedoutsothatthereisnoriskofpeopleor
objects being crushed. It must always be executed in accordance
withcurrentlegislationonthesubject.
Sensibility adjustment of the gate collision detection (only with
encoderpresent)
3.
ThistrimmerallowsthePAUSEtimetobeadjustedbetween0and
60 seconds. Set DIP SWITCH 1 to the ON position to enable
automaticclosing.
P.N.: TURNING THE TRIMMERS CLOCKWISE INCREASES THE TIMES/VALUES
+
-
+
-
+
-
+
-
MOTOR CONNECTIONS
M6
1 2 3 4 5
Left hand: right hand :
Limit switch1(M1): 7 yellow limit switch1(M1): 8 yellow
Limit switch2 (M1): 8 green limit switch2 (M1): 7 green
Motor (M1): 1 purple Motor (M1): 2 purple
Motor (M1): 2 White Motor (M1): 1 White
Motor 24 (M6): Motor 24 (M6):
1 (-) battery / com motor 1 (-) battery / com motor
2 (+) battery 2 (+) battery
3 (+) battery 3 (+) battery
4 not connected 4 right motor
5 left motor 5 not connected
1 2 3 4 5 6 7 8 9 10
M1
8
PRE-GATE
International registered trademark n. 2.777.971
Motor (M1) neutral: black Motor (M1) neutral: black
REV 07 - 09/201067411095

Green
White
Brown
MOTOR 115V, LIMIT SWITCH, ENCODER
Limit Switches
They can be of different types:
- inductive limit switch
- mechanical limit switch with lever
- limit switch with spring
- limit switch for motor-reducer with chain.
All these limit switches must be
manufactured by SEA for a complete
compatibilityoftheconnectors
Com = Common
Encoder(reversingsensor)
The encoder is a system which detects any
obstacleduringtherunningofthegate.
Tousethissystemitisnecessarytopurchasea
SEAmotorprovidedwithencoder.
If the encoder function is activated (DIP 4 to
OFF position), in case it will detect an error or
anobstacle,youwill getthemovementreverse
forabout2seconds.
Never disconnect the operating of this primary
entrapmentprotection.
WARNING:SEAwill neverbe responsiblein
case of damages if the reversing sensor
hasbeendisconnected.
7
8
9
9
69
!
Limit Switch
closing
Limit Switch opening
Com
C
Com
C
-
+
9
MAX TORQUE
TIMER
REVERSE SENS
AUX_POW_SUP
24VDC
COMMON
START
COMMON
PARTIALSTART
M8-1
M8-5
OPEN STOP CLOSE
CENTRAL
SAFETY
1 2 3 4 5 6 7 8
1 2 3
RESET ALL.
KEEP ALARM
NOT KEEP ALARM
1 2 3 4 5 6 7 8 9 10
M1
M1
Motor 115Vac
Output for motor connection
O = OPEN
C = CLOSED
Com = COMMON
(motor black cable)
Com
O/C O/C
Black
1
2
3
example
example
Com
C C
10
PRE-GATE
International registered trademark n. 2.777.971
REV 07 - 09/201067411095

1 2 3 4 5 6
SAFETY LOOP, CENTRAL LOOP, EXIT LOOP
MAX TORQUE
TIMER
REVERSE SENS
AUX_POW_SUP
24VDC
COMMON
START
COMMON
PARTIALSTART
M8-1
M8-5
OPEN STOP CLOSE
CENTRAL
SAFETY
1 2 3 4 5 6 7 8
1 2 3
RESET ALL.
KEEP ALARM
NOT KEEP ALARM
M2
M2
On the control unit there can be sited three loop detector modules
forthedetectionof avehicle:
Modulesafety:behaveslikeaSAFETYLOOP
Modulecentre:behaveslikeaphotocell(functionnotenabled)
IfDS1-1isswitchONtheEXLOOPworklikeatimer.
Module exit: if the DIP DS1-1 is placed to OFF and a loop is
connected to the entry EXLOOP, when an obstacle occupies the
loop,itcausesthereclosingofthegate..
SA ETY
F
OPLO
CENTR LA
PLOO
FREE EXIT
LOOP
12
34
5
6
example
10
PRE-GATE
International registered trademark n. 2.777.971
REV 07 - 09/201067411095

POWER SUPPLY, WARNING LAMP, COURTESY LIGHT
MAX TORQUE
TIMER
REVERSE SENS
AUX_POW_SUP
24VDC
COMMON
START
COMMON
PARTIALSTART
M8-1
M8-5
OPEN STOP CLOSE
CENTRAL
SAFETY
1 2 3 4 5 6 7 8
1 2 3
RESET ALL.
KEEP ALARM
NOT KEEP ALARM
M4
M4
1 2 3 4 5
M3
M3
Power input
Input for the connection of the electric power.
P = PHASE
L = LINE
NOTICE: for the connection to the electric power see the law in force.
L P
2
1
1 2
4
5
CourtesyLight
(115Vmax100W)
Exit by relay RL1 (com M4/5, no
M4/4)the relay switchesonforthe
whole opening cycle of the gate
and stays on also after the gate's
closingforatimeperiod whichhas
tobedefined.
FlashingLamp(115V)
The flashing lamp is an
important accessory which
warnsthegateoperating.
Exit by relay RL2 (com M4/2, no
M4/1) activates some seconds
before the gate begins to move,
and switches off some seconds
afterthegatehasstopped.
The exit rests closed during the
functioning, this means that the
intermittence of the flashing light
isnotcontrolled.
1
2
11
LP
Note: this connection
can be executed
through the 24V
auxiliary exit instead
through the 110V exit
PRE-GATE
International registered trademark n. 2.777.971
REV 07 - 09/201067411095

MAGNETIC LOCK, SOLENOID LOCK,
INTRUSION CONTACT, BUZZER
MAX TORQUE
TIMER
REVERSE SENS
AUX_POW_SUP
24VDC
COMMON
START
COMMON
PARTIALSTART
M8-1
M8-5
OPEN STOP CLOSE
CENTRAL
SAFETY
1 2 3 4 5 6 7 8
1 2 3
RESET ALL.
KEEP ALARM
NOT KEEP ALARM
1 2 3 4 5 6 7 8 9 10
M5
M5
ON
OFF
Alarm control: A circuit of
selfblockingoftherelayalso
foreseen which is selected
by bridge J1. When the
bridge J1 is inserted the
relay RL3 rests activated
until it is not reset with the
external contact n.o.
ALLARM (M5/8, M5/9) or
with the push button on
board of the control unit
RESETALL
IMPORTANT: UL325 standards requires an audible alarm to go OFF
after 2 consecutive events detected by the primary entrapment
protection of the gate operator (for ex. reversing sensor).
!
7
6
Buzzer(24Vdc)
AudibleAlarm
Use a buzzer 24Vdc of
100 dB. The buzzer will
be switched on after two
consecutive activations
oftheanticrushsensor.
Toresettheallarmitisnecessary to push the button STOP.Anyway
after 5 minuts the buzzer will stop to sound and the automation
standsstillwaitingforcommands.
8 9
-
MagneticLockand
Solenoid Lock
wiring: Exit with
relay RL5 (com
M5/3, no M5/2, nc
M5/1); is enabled for
0,5” for the activation
oftheelectriclock.
The Power Supply is not provided.
N.C. N.O.
Magnetic Lock
Solenoid Lock
Power forMagnetic / Solenoid Lock
3
1 or 2
Intrusion contact: exit with relay RL4
(com M5/5, no M5/4) when the limit switch
of the closed gate de-activates without any
opening command, the relay closes for a
timeperiodwhichhastobedefined. 4 5
12
PRE-GATE
International registered trademark n. 2.777.971
REV 07 - 09/201067411095

BATTERIES, 24Vdc MOTORS
13
PRE-GATE
International registered trademark n. 2.777.971
1 2 3 4 5
MAX TORQUE
TIMER
REVERSE SENS
AUX_POW_SUP
24VDC
COMMON
START
COMMON
PARTIALSTART
M8-1
M8-5
OPEN STOP CLOSE
CENTRAL
SAFETY
1 2 3 4 5 6 7 8
1 2 3
RESET ALL.
KEEP ALARM
NOT KEEP ALARM
M6
M6
Motor24VdcLEFT
Controlof the gateopening in case of power
failure. This control closes two contacts of
two relays which control an external module
for the administration of the movement of a
motorwith24Vdccontinuouscurrent.
Thecontactsarethefollowing:
24Vdc Motor on the left hand side M6/5
closedonM6/3
Com=COMMON
3
5
example
Motor24VdcRIGHT
Controlofthegateopeningincaseof power
failure. This control closes two contacts of
two relays which control an external module
for the administration of the movement of a
motorwith24Vdccontinuouscurrent.
Thecontactsarethefollowing:
24Vdc Motor on the right hand side M6/4
closedonM6/3
Com=COMMON
3
4
example
Com
Com
24Vdc Battery charger
The backup battery allows
toexecute an opening cycle
in case of power cut, so that
it’s possible to exit through
the gate and keep the gate
openuntil the currentwill be
reconnected.
2
1
-
+
-
+
+
-
Com
REV 07 - 09/201067411095

OPENING/CLOSING, KEY BUTTON ENABLE,
CARD READER, FIRE SWITCH
MAX TORQUE
TIMER
REVERSE SENS
AUX_POW_SUP
24VDC
COMMON
START
COMMON
PARTIALSTART
M8-1
M8-5
OPEN STOP CLOSE
CENTRAL
SAFETY
1 2 3 4 5 6 7 8
1 2 3
RESET ALL.
KEEP ALARM
NOT KEEP ALARM
1 2 3 4 5 6 7 8
M9
M9
FireSwitch:
Contact n.o. controls the opening of the gate, which
restsopeneduntil theconsentshasbeentakenaway.
When released the gate automatically closes again if
the DIP DS1-1 is on ON, otherwise to restore the
movement is necessary to activate first the Stop and
thentheSTART. 8
7
-
-
ON
FF
O
Key button enable: The first three accesses are foreseen
for a pushbutton board sited in a porter's lodge, and it is
foreseen that it can be switched off during certain hours
during day. Therefore the following three accesses are
enabled through key button ENABLE (M9/5) with the
followingconfiguration: 5
4-
-
6
4-
Card/Start:
Contact n.o. controls the opening of the gate; the re-
closing can be executed by a command from the
external loop car presence or after an adjusted time
period(3to60sec.,bytrimmer“TIMER”).
OPEN
STOP
CLOSE
Opening/Closingswitch
OPEN: contact n.o. controls the opening
command of the gate which remains opened
until a new closing command is given or until
anadjusted time period (3 to60 sec.) through
Timer haspassed.
STOP: Contact n.c. stops immediately the
movement of the gate, furthermore it resets
somealarmconditions.
CLOSE: Contact n.o. controls the closing of
thegate.
1
2
3
C
O
o = open
c = close
KeybuttonENABLEclosedatGND => OPEN,STOP,CLOSEenabledandEXLOOPswitchedoff
KeybuttonENABLEopen => OPEN,STOP,CLOSEswitchedoffandEXLOOPenabled
14
PRE-GATE
International registered trademark n. 2.777.971
REV 07 - 09/201067411095

7 8 9 10 11 12 13 14 15
PHOTOCELLS, SAFETY EDGE
PHOTOCELL:Photocellsconnection
This contact can function in n.o. or n.c. mode,
depending on how the dip switch DS1-2 has been
adjusted:
DS1-2=ON=>functionn.o.
DS1-2=OFF=>functionn.c.
When activated the movement of the gate stops
immediately, if it is occupied for more than two
seconds,thegatewillreversethemovement..
+=24Vdc -=0Vdc C=Contact
Com=Common
RX
TX
+
-
Com
N.C.
14 13 11
MAX TORQUE
TIMER
REVERSE SENS
AUX_POW_SUP
24VDC
COMMON
START
COMMON
PARTIALSTART
M8-1
M8-5
OPEN STOP CLOSE
CENTRAL
SAFETY
1 2 3 4 5 6 7 8
1 2 3
RESET ALL.
KEEP ALARM
NOT KEEP ALARM
M9
M9
It is a n.c. contact, which stops immediately the movement of the gate.Afurther safety can be
obtained making a connection with the safety edge mentioned on the side. If it is start up, the
safetyedgereversesthemovementofthegatefortwosecondsanditstops.
Notice:ifthesafetyinputisnotused,makeaJumperbetween12and14.
Safety edge input:
812
- - +
C
MASTER / SLAVE CONNECTIONS
MAX TORQUE
TIMER
REVERSE SENS
AUX_POW_SUP
24VDC
COMMON
START
COMMON
PARTIALSTART
M8-1
M8-5
OPEN STOP CLOSE
CENTRAL
SAFETY
1 2 3 4 5 6 7 8
1 2 3
RESET ALL.
KEEPALARM
NOT KEEP ALARM
MAX TORQUE
TIMER
REVERSE SENS
AUX_POW_SUP
24VDC
COMMON
START
COMMON
PARTIALSTART
M8-1
M8-5
OPEN STOP CLOSE
CENTRAL
SAFETY
1 2 3 4 5 6 7 8
1 2 3
RESET ALL.
KEEPALARM
NOT KEEP ALARM
1 2 3 1 2 3
MASTER control unit SLAVE control unit
M7
M7 M7
M7
Itisselectedbyadipswitchinthefollowingway: DS1-6=ON=>presenceSLAVEcard DS1-6=OFF=>absenceSLAVEcard
IftheuseoftheSLAVEcardisforeseen,gatewithtwoleaves,itisconnectedtotheMastercardthrough serialconnectionRS485
andreceivesfromthislastoneall information,alsothoseofsecurity. 15
PRE-GATE
International registered trademark n. 2.777.971
REV 07 - 09/201067411095

DIP SWITCHES
MAX TORQUE
TIMER
REVERSE SENS
AUX_POW_SUP
24VDC
COMMON
START
COMMON
PARTIALSTART
M8-1
M8-5
OPEN STOP CLOSE
CENTRAL
SAFETY
1 2 3 4 5 6 7 8
1 2 3
RESET ALL.
KEEP ALARM
NOT KEEP ALARM
DS1
1 2 3 4 5 6 7 8
ON
DS1
1
2
3
4
5
6
7
8
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ClosingforautomaticcycleestablishedbytrimmerTIMER(3-60sec.)
Closingforautomaticcyclewithdetectionattraversol’EXLOOP
Photocelln.o.
Photocelln.c.
When a car transits on the safeloop or the photocell intervened, in closing, stops for 3 sec. then
opensuntilthealarmstops
When a car transits on the safeloop or the photocell intervened, stands still as long as passage
restsoccupied.
EncoderPresence
EncoderAbsence
Opening on the right hand side of the leaf commanded by Master card, on the left hand side for
theonecommandedbytheSlavecard
Openingonthelefthandsideofthe leafcommandedbyMastercard,ontherighthandsideforthe
onecommandedbytheSlavecard
Slavecardpresence
Slavecardnotpresent
Learning modality: execute one complete opening to memorize the moving time if there is no
encoderorthepositionifthereisanencoder.AfterwardsputtheDIPonOFF.
Learningexecuted
DESCRIPTION
DS1 ON/OFF
16
PRE-GATE
International registered trademark n. 2.777.971
Preblinkactivated
Preblinkdisabled
REV 07 - 09/201067411095

DIP SWITCHES
Themastercardfunctionsnormally
ThemastercardfunctionsasSlave
AutotestPhotocellEnable
AutotestPhotocellDisable
1
2
ON
OFF
ON
OFF
MAX TORQUE
TIMER
REVERSE SENS
AUX_POW_SUP
24VDC
COMMON
START
COMMON
PARTIALSTART
M8-1
M8-5
OPEN STOP CLOSE
CENTRAL
SAFETY
1 2 3 4 5 6 7 8
1 2 3
RESET ALL.
KEEP ALARM
NOT KEEP ALARM
DS2
1 2 3 4
ON
DS2
DESCRIPTIONON/OFF
Free
Free
4ON
OFF
17
PRE-GATE
International registered trademark n. 2.777.971
DS2
Softstartenabled
Softstartdisabled
3ON
OFF
REV 07 - 09/201067411095

GENERAL WARNING: Installation must be realized using parts and accessories approved by SEA. SEA is not
responsibleforincorrect installationsand/ornon-compliancewith safetystandardsaccordingto the lawin-force. SEAisin
no way liable for any damages and/or malfunctioning due to using parts and accessories non-compliant with the UL325
safetystandards.
ORDERS: Orders are processed upon approval by SEA. Buyers must confirm orders by sending a written Purchase
Orders to SEA. Purchase Orders are intended as confirmation of orders and binding for the buyer, which accepts SEA
salescondition.
QUOTATION:Quotationandspecialofferswithanon-specifieddurationexpiresautomaticallyafter30days.
PRICES: Prices are based on the Price List in force. Discounts and quotation from Sales Rep. and other selling branches
must be approved by SEA. Prices are F.O.B SEAWarehouse in Miami and do not include shipments costs. SEAreserves
therighttomodifythepricelistatanytimeandprovidenoticetoitssalesnetwork.
PAYMENT:MethodofpaymentsandtermsarenotifiedbySEAanddisplayedonthecommercialinvoice.
DELIVERY: The delivery time on the invoice is not binding and represents an estimated delivery. Shipments costs will be
chargedtothebuyerandSEAisnotresponsiblefordelaysand/ordamagesoccurredtotheproductsduringshipment.
COMPLAINS: Complains and/or claims must be notified to SEA within 7 business days after receiving the products.
Claims and complains must be supported by original documents. Customer must contact the factory for instructions and
authorization. Merchandise returned for credit must be current, uninstalled and unused and returned in its original
packaging.Freightmustbepre-paidonallauthorizedreturns.
REPAIRS: Repairs and parts are subject to the availability in stock. Shipment of products for repairs must be pre-paid by
the customer. Products shipped without authorization, sender’s details and description of the problems will be refused.
CustomersmustcontactSEAforinstructions.
WARRANTY:fortheoriginalbuyeronly:
Hydraulic and oil-bath motors: 36 months warranty from the date of invoice on manufacturing, assembling and
workmanshipdefects.
Electro-mechanic motors and electronic control systems: 24 months warranty from the date of invoice on manufacturing,
assemblingandworkmanshipdefects.
Lepus and Full Tank Standard model: 60 months warranty from the date of invoice on manufacturing, assembling and
workmanshipdefects.
No warranty will be recognized for damages due to incorrect installation and/or improper use for which the product was
intended. SEA warranty obligations shall be limited to repair or replace the defective product/parts at SEAoption, upon
examinationoftheproductsbySEAtechnicalStaff.AllreplacedpartsmustremainpropertyofSEA.Thewarrantystatusof
theproductremainsanunquestionableassessmentofSEA.Buyermustshippre-paiddefectiveproducts.Productsunder
warranty will be returned pre-paid by SEA. Recognized defects, whatever their nature, will not produce any responsibility
and/ordamageclaimstoSEAUSAIncandSEAs.r.l.Warrantyshallnotcoveranyrequiredlaboractivities.Warrantywillin
no case be recognized if alterations and any other changes will be found on products. Warranty will not cover damages
caused by carriers, expendable materials and faults due to improper use with the products specifications. No indemnities
are recognized during repairing and/or replacing of the products under warranty. SEAUSAInc. and SEAs.r.l. decline any
responsibility for damages to person and objects deriving from non-compliance with safety standards, installation
instructionsoruse ofthe productssold.Itis intendedthat warrantywillbe recognizedonly onproductsboughtthrough the
SEA authorized network. Products must be installed by professionals. No warranty will be recognized if products are
installed directly by the final user. Warranty does not apply in case of unexpected events such as fire, flood, electrical
powersurge,lightning,vandalismandothers.
SEAUSAInc.isnotresponsibleforerrorsintechnicalinformationprintedincatalogsandinstallationmanuals.
SALES CONDITIONS and WARRANTY
18
PRE-GATE
International registered trademark n. 2.777.971
REV 07 - 09/201067411095

International registered trademark n. 2.777.971
web site: www.sea-usa.com
e-mail: [email protected]
SEA USA Inc.
10850 N.W. 21st unit 160 DORAL MIAMI
Florida (FL) 33172
Phone:++1-305.594.1151 Fax: ++1-305.594.7325
Toll Free: 800.689.4716