Sony HDCU2500 User manual

HD CAMERA CONTROL UNIT
HDCU2500
3G/HD SDI OUTPUT EXPANSION UNIT
HKCU2007
SD ENCODER UNIT
HKCU1001
MULTI INTERFACE UNIT
HKCU1003
MAINTENANCE MANUAL
1st Edition

警告
このマニュアルは， サービス専用です。
お客様が， このマニュアルに記載された設置や保守， 点検， 修理などを行うと感電や火災，
人身事故につながることがあります。
危険をさけるため， サービストレーニングを受けた技術者のみご使用ください。
WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
Model Name Serial No.
HDCU2500 (SY) 10001 and Higher
HDCU2500 (CE) 40001 and Higher
For safety, do not connect the connector for peripheral
device wiring that might have excessive voltage to the
following port(s).
: LAN connector
: NETWORK TRUNK connector
Follow the instructions for the above port(s).
安全のために，周辺機器を接続する際は，過大電圧を
持つ可能性があるコネクターを以下のポートに接続し
ないでください。
：LAN 端子
：NETWORKTRUNK 端子
上記のポートについては本書の指示に従ってください。
HDCU2500

For kundene i Norge
Dette utstyret kan kobles til et IT-strømfordelingssystem.
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
CAUTION
The use of optical instruments with this product will
increase eye hazard.
The HDCU2500 is classified as a CLASS 1 LASER
PRODUCT.
HDCU2500

CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type rec-
ommended by the manufacturer.
When you dispose of the battery, you must obey the
law in the relative area or country.
ATTENTION
Il y a danger d’explosion s’il y a remplacement incor-
rect de la batterie. Remplacer uniquement avec
une batterie du même type ou d’un type équivalent
recommandé par le constructeur.
Lorsque vous mettez la batterie au rebut, vous devez
respecter la législation en vigueur dans le pays ou la
région où vous vous trouvez.
VORSICHT
Explosionsgefahr bei Verwendung falscher Batterien.
Batterien nur durch den vom Hersteller empfohlenen
oder einen gleichwertigen Typ ersetzen.
Wenn Sie die Batterie entsorgen, müssen Sie die
Gesetze der jeweiligen Region und des jeweiligen
Landes befolgen.
注意
指定以外の電池に交換すると，破裂する危険があります。
必ず指定の電池に交換してください。
使用済みの電池は，国または地域の法令に従って
処理してください。
FÖRSIKTIGHET!
Fara för explosion vid felaktigt placerat batteri.
Byt endast mot samma eller likvärdig typ av batteri,
enligt tillverkarens rekommendationer.
När du kasserar batteriet ska du följa rådande lagar
för regionen eller landet.
PAS PÅ
Fare for eksplosion, hvis batteriet ikke udskiftes
korrekt.
Udskift kun med et batteri af samme eller tilsvarende
type, som er anbefalet af fabrikanten.
Når du bortskaffer batteriet, skal du følge
lovgivningen i det pågældende område eller land.
HUOMIO
Räjähdysvaara, jos akku vaihdetaan virheellisesti.
Vaihda vain samanlaiseen tai vastaavantyyppiseen,
valmistajan suosittelemaan akkuun.
Noudata akun hävittämisessä oman maasi tai
alueesi lakeja.
FORSIKTIG
Eksplosjonsfare hvis feil type batteri settes i.
Bytt ut kun med samme type eller tilsvarende
anbefalt av produsenten.
Kasser batteriet i henhold til gjeldende avfallsregler.
⊼ᛣ
⊼ᛣ
བᵰ᳈ᤶⱘ⬉∴ϡℷ⹂ˈህӮ᳝⟚⚌ⱘ䰽DŽ
া᳈ᤶৠϔ㉏ൟ៪ࠊ䗴ଚ᥼㤤ⱘ⬉∴ൟোDŽ
໘⧚⬉∴ᯊˈᖙ乏䙉ᅜⳌ݇ഄ៪೑ᆊⱘ⊩ᕟDŽ
HDCU2500

本機をラックに設置するとき
熱の適切な排気・発散を得るために，ラックと本機の間
には空間を確保してください。
Attention-when the product is installed in Rack:
1. Prevention against overloading of branch circuit
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
make sure that the rack does not overload the supply
circuit.
2. Providing protective earth
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
confirm that the outlet is provided with a suitable
protective earth connection.
3. Internal air ambient temperature of the rack
When this product is installed in a rack, please make
sure that the internal air ambient temperature of the
rack is within the specified limit of this product.
4. Prevention against achieving hazardous
condition due to uneven mechanical loading
When this product is installed in a rack, please
make sure that the rack does not achieve hazardous
condition due to uneven mechanical loading.
5. Install the equipment while taking the operating
temperature of the equipment into consideration
For the operating temperature of the equipment, refer
to the specifications of the Operation Manual.
6. When performing the installation, keep the space
away from walls in order to obtain proper exhaust
and radiation of heat.
HDCU2500

Table of Contents
Manual Structure
Purpose of this manual....................................................................................................................7
Related manuals...........................................................................................................................7
1. Service Overview
1-1. Checking the ROM and Software Version....................................................................................1-1
1-1-1. ROM....................................................................................................................1-1
1-1-2. Software................................................................................................................1-1
1-2. Power Cord....................................................................................................................1-2
1-3. Connectors and Cables........................................................................................................1-3
1-3-1. Connector Input/Output Signals of HDCU2500.......................................................................1-3
1-3-2. Connector Input/Output Signals of HKCU2007.......................................................................1-6
1-3-3. Connector Input/Output Signals of HKCU1001.......................................................................1-6
1-3-4. Connector Input/Output Signals of HKCU1003.......................................................................1-7
1-3-5. Wiring Diagrams for Cables............................................................................................1-8
1-3-6. Connection Connectors/Cables.........................................................................................1-8
1-3-7. Note in Connecting CAMERA Connector.............................................................................1-9
1-4. Location of Printed Circuit Boards..........................................................................................1-10
1-5. Outside Dimensions..........................................................................................................1-11
1-6. Functions of Onboard Parts..................................................................................................1-12
1-6-1. Description of Onboard LED Indicators..............................................................................1-12
1-6-2. Functions of Onboard Switches.......................................................................................1-15
1-6-3. Functions of Onboard Potentiometers.................................................................................1-18
1-7. Service Tools/Measuring Equipment List...................................................................................1-20
1-7-1. Service Tools..........................................................................................................1-20
1-7-2. Measuring Equipment.................................................................................................1-20
1-8. Cautions when Replacing the Lithium Battery..............................................................................1-21
1-8-1. Replacing Procedure..................................................................................................1-21
1-9. Replacing the Flexible Card Wires..........................................................................................1-22
1-10. Option Board Installation Position...........................................................................................1-23
1-10-1. When Installing Option Model........................................................................................1-23
1-11. Installing the Option Board..................................................................................................1-24
1-11-1. Front Side (HKCU2007)..............................................................................................1-24
1-11-2. Rear Side (HKCU2007)...............................................................................................1-25
1-11-3. Front Side (HKCU1001/1003)........................................................................................1-26
1-11-4. Rear Side (HKCU1001/1003).........................................................................................1-27
1-12. Writing and Rewriting the PLD Internal Data...............................................................................1-28
1-12-1. e-Production System Has the Advantages Shown Below.............................................................1-28
1-13. Circuit Protective Devices...................................................................................................1-30
1-13-1. Fuse....................................................................................................................1-30
1-13-2. Thermistor.............................................................................................................1-30
1-14. Cleaning of Connector/Cable................................................................................................1-33
1-14-1. When the Optical Connector Cleaner (Commercially Available) is Available.......................................1-33
1-14-2. When the Optical Connector Cleaner (Commercially Available) is not Available...................................1-34
1-15. Circuit Description...........................................................................................................1-38
1-15-1. Front Boards...........................................................................................................1-38
1-15-2. Rear Boards...........................................................................................................1-39
1-15-3. HKCU2007............................................................................................................1-40
HDCU2500 1

1-15-4. HKCU1001............................................................................................................1-40
1-15-5. HKCU1003............................................................................................................1-41
1-16. Lead-free Solder.............................................................................................................1-42
2. System Setup
2-1. System Connection............................................................................................................2-1
2-1-1. Example of Connection.................................................................................................2-2
2-1-2. Standard 3G/HD/SD System...........................................................................................2-3
2-1-3. Standard 3G/HD/SD System with SD Analog Encoder (HKCU1001)................................................2-4
2-1-4. Standard 3G/HD/SD System with 3G Signal Interface (HKCU2007).................................................2-5
2-2. Setting the System Formats...................................................................................................2-6
2-2-1. Setting the Multi-Format...............................................................................................2-6
2-2-2. Setting the Reference Input.............................................................................................2-6
2-3. Audio System.................................................................................................................2-7
2-3-1. Setting the Intercom System............................................................................................2-7
2-3-2. Microphone Setting.....................................................................................................2-9
2-4. System Settings..............................................................................................................2-11
2-4-1. Tally System Setting..................................................................................................2-11
2-4-2. Camera Number Setting...............................................................................................2-11
2-4-3. Connecting the Control, Intercom, Tally and Audio Signals.........................................................2-12
2-5. Video Signal System.........................................................................................................2-13
2-5-1. Input/Output Signal Selection.........................................................................................2-13
2-5-2. Signal Phase Adjustment..............................................................................................2-13
2-5-3. Aspect Ratio Setting for Down-Conversion..........................................................................2-14
2-5-4. VBS Signal Level Adjustment (Only When HKCU1001/1003 is Installed).........................................2-16
2-5-5. Waveform Monitor Signal Level Adjustment (Only When HKCU1001/1003 is Installed)..........................2-17
2-5-6. Stair Case Signal Adjustment Procedure (Only When HKCU1001/1003 is Installed)...............................2-18
2-5-7. Picture Monitor Signal Level Adjustment (Only When HKCU1001/1003 is Installed)..............................2-19
2-5-8. RETURN Input Signal................................................................................................2-20
3. Menu Settings
3-1. Preparations...................................................................................................................3-1
3-1-1. Display/Hide the Status Screen.........................................................................................3-1
3-1-2. Starting/Exiting the Maintenance Mode................................................................................3-1
3-1-3. Memory Stick...........................................................................................................3-2
3-2. Status Display.................................................................................................................3-3
3-2-1. Camera Settings........................................................................................................3-3
3-2-2. Settings of Entire System...............................................................................................3-4
3-2-3. Status of Internal Boards...............................................................................................3-4
3-2-4. Camera System Diagnostics............................................................................................3-4
3-2-5. Network Diagnostics...................................................................................................3-5
3-2-6. Board Diagnostics......................................................................................................3-6
3-2-7. Status of the Board Inserted in Slot.....................................................................................3-7
3-2-8. SDP Board Diagnostics.................................................................................................3-8
3-2-9. Camera Board Status...................................................................................................3-9
3-2-10. Version Information of ROMs in Each Unit...........................................................................3-9
3-3. SYSTEM OPERATION Menu..............................................................................................3-10
3-4. CCU CONFIGURATION Menu............................................................................................3-16
3-5. NETWORK SETTINGS Menu..............................................................................................3-27
HDCU2500 2

3-6. VE OPERATION Menu.....................................................................................................3-29
3-7. MAINTENANCE Menu.....................................................................................................3-39
4. Replacement of Main Parts
4-1. General Information for Parts Replacement..................................................................................4-1
4-1-1. Index....................................................................................................................4-1
4-1-2. Basic Knowledge.......................................................................................................4-3
4-2. Power Supply Unit............................................................................................................4-4
4-2-1. Power Block Assembly (D00)..........................................................................................4-4
4-2-2. DC Fan..................................................................................................................4-5
4-2-3. RE-274 Board...........................................................................................................4-7
4-2-4. PS-778D00 Board......................................................................................................4-8
4-2-5. Notes on Disassembling the Power Block Assembly (D00)..........................................................4-10
4-3. Front Panel...................................................................................................................4-13
4-3-1. Removal and Installation of Front Panel..............................................................................4-13
4-3-2. CN-3451 Board........................................................................................................4-13
4-3-3. AU-340 Board / LE-377 Board.......................................................................................4-14
4-4. Rear Panel....................................................................................................................4-16
4-4-1. Removal and Installation of Rear Panel Assembly...................................................................4-16
4-4-2. SDP-17 Board.........................................................................................................4-16
4-5. Plug-In Board................................................................................................................4-19
4-5-1. Installing/Removing Plug-in Boards on the Front Side...............................................................4-19
4-5-2. Installing/Removing Plug-in Boards and Blank Panels on the Rear Side............................................4-20
4-6. Main Frame..................................................................................................................4-21
4-6-1. HIF-62 Board..........................................................................................................4-21
4-6-2. SDI-99 Board..........................................................................................................4-21
4-6-3. CN-2675G Board......................................................................................................4-22
4-6-4. CN-2676 Board........................................................................................................4-23
4-6-5. CN-2677G Board......................................................................................................4-24
4-6-6. VIF-52 Board..........................................................................................................4-25
4-6-7. ADO-12 Board........................................................................................................4-26
4-6-8. CNB-29A Board.......................................................................................................4-27
4-6-9. MB-1181 Board.......................................................................................................4-28
5. Electrical Alignment
5-1. Preparations...................................................................................................................5-1
5-1-1. Equipment Required....................................................................................................5-1
5-1-2. Notes on Adjustments..................................................................................................5-1
5-1-3. Connection of Equipment..............................................................................................5-2
5-1-4. Initialization Settings...................................................................................................5-2
5-2. Audio System Adjustment....................................................................................................5-4
5-2-1. RTS Intercom Adjustment..............................................................................................5-4
5-3. Video/Reference Signal System Adjustment..................................................................................5-7
5-3-1. 27 MHz VCO Free-Running Adjustment..............................................................................5-7
5-3-2. Clock (74 MHz) Duty Adjustment.....................................................................................5-7
5-3-3. Prompter 1/2 Level Adjustment........................................................................................5-8
5-3-4. STAIR CASE Adjustment..............................................................................................5-9
5-4. SD Signal System Adjustment...............................................................................................5-11
5-4-1. VBS Output Level Adjustment........................................................................................5-11
HDCU2500 3

5-4-2. PIX Output Level Adjustment........................................................................................5-11
5-4-3. WF Output Level Adjustment.........................................................................................5-12
6. Spare Parts
6-1. Note on Repair Parts..........................................................................................................6-1
6-2. Exploded Views...............................................................................................................6-2
6-3. Electrical Parts List............................................................................................................6-7
6-4. Supplied Accessories........................................................................................................6-98
7. Block Diagrams
Overall..................................................................................................................................7-1
8. Schematic Diagrams
ADO-12.................................................................................................................................8-1
AT-167A................................................................................................................................8-2
AU-340................................................................................................................................8-11
AVP-15................................................................................................................................8-12
CN-2675G.............................................................................................................................8-21
CN-2676...............................................................................................................................8-22
CN-2677G.............................................................................................................................8-22
CN-3451...............................................................................................................................8-22
CNB-29A..............................................................................................................................8-23
DRX-9.................................................................................................................................8-24
DTX-9.................................................................................................................................8-32
EN-159A..............................................................................................................................8-39
EN-159B..............................................................................................................................8-46
HIF-26.................................................................................................................................8-53
HIF-57.................................................................................................................................8-54
HIF-62.................................................................................................................................8-55
LE-379.................................................................................................................................8-56
MB-1181..............................................................................................................................8-57
PS-778D00............................................................................................................................8-60
RC-105................................................................................................................................8-63
RE-274................................................................................................................................8-72
SDI-99.................................................................................................................................8-75
SDP-17................................................................................................................................8-77
VDA-64A.............................................................................................................................8-87
VDA-64B..............................................................................................................................8-88
VIF-52.................................................................................................................................8-89
Frame Wiring..........................................................................................................................8-92
9. Board Layouts
ADO-12.................................................................................................................................9-1
AT-167A................................................................................................................................9-2
AU-340.................................................................................................................................9-4
HDCU2500 4

AVP-15.................................................................................................................................9-5
CN-2675G..............................................................................................................................9-6
CN-2676................................................................................................................................9-6
CN-2677G..............................................................................................................................9-7
CN-3451................................................................................................................................9-7
CNB-29A...............................................................................................................................9-7
DRX-9..................................................................................................................................9-8
DTX-9.................................................................................................................................9-10
EN-159A, EN-159B...................................................................................................................9-12
HIF-26.................................................................................................................................9-14
HIF-57.................................................................................................................................9-14
HIF-62.................................................................................................................................9-15
LE-379.................................................................................................................................9-15
MB-1181..............................................................................................................................9-16
PS-778D00............................................................................................................................9-17
RC-105................................................................................................................................9-19
RE-274................................................................................................................................9-21
SDI-99.................................................................................................................................9-22
SDP-17................................................................................................................................9-23
VDA-64A, VDA-64B.................................................................................................................9-24
VIF-52.................................................................................................................................9-24
Board Parts Location..................................................................................................................9-25
HDCU2500 5

Manual Structure
Purpose of this manual
This manual describes the information items that premise the service based on the components parts assuming use of
system and service engineers.
Related manuals
The following manuals are available in this model.
If this manual is required, please contact your local Sony Sales Office/Service Center.
• Operation Manual (Supplied with this unit)
This manual is necessary for application and operation of this unit.
HDCU2500 7

Section 1
Service Overview
1-1. Checking the ROM and Software Version
When connecting the peripheral equipment in the list below to this unit, be sure to check that the ROM and software
version on each peripheral device is corresponding to this unit to be connected. If the ROM and software version is
lower than the specified below, be sure to perform ROM replacement and updating the software.
If ROM replacement and updating the software are required, contact your local Sony Sales Office/Service Center.
1-1-1. ROM
Peripheral equipment Board name Ref. No. ROM version
MSU-900/950 CPU-396 IC18, IC31 Ver.1.02 and higher
MSU-1000/1500 MPU-150/151 IC15, 16 Ver.2.00 and higher*1
RCP-920/921 MPU-143 IC13, 14 Ver.1.11 and higher
RCP-1000/1001 MPU-152 IC15, 16 Ver.2.00 and higher*1
PCP-1500/1501 MPU-153 IC14, 15 Ver.2.00 and higher*1
RCP-1530 MPU-153 IC14, 15 Ver.2.00 and higher*1
1-1-2. Software
Peripheral equipment Board name ROM version
HDC-1500R AT-163 Ver.1.27 and higher
MSU-900/950 CPU-396 Ver.1.02 and higher
MSU-1000/1500 MPU-150/151 Ver.2.00 and higher*1
RCP-920/921 MPU-143 Ver.1.11 and higher
RCP-1000/1001 MPU-152 Ver.2.00 and higher*1
PCP-1500/1501 MPU-153 Ver.2.00 and higher*1
RCP-1530 MPU-153 Ver.2.00 and higher*1
*1: Will be supported after functions are added in the future
HDCU2500 1-1

1-2. Power Cord
To get a power cord, please contact your local Sony Sales Office/Service Center.
WARNING
• Use the approved Power Cord (3-core mains lead)/Appliance Connector/Plug with earthing-contacts
that conforms to the safety regulations of each country if applicable.
• Use the Power Cord (3-core mains lead)/Appliance Connector/Plug conforming to the proper ratings
(Voltage, Ampere).
• Never use an injured power cord.
HDCU2500 1-2

1-3. Connectors and Cables
1-3-1. Connector Input/Output Signals of
HDCU2500
Input Signals
1. HD PROMPTER IN
• BNC type
• BTA S-004/SMPTE 292M compliant
75 Ω, 1.485 Gbps/1.4835 Gbps
2. RET1, 2, 3
• BNC type
• VBS (Analog composite signals): 1.0 V p-p , 75 Ω
• 3G-SDI: SMPTE 424M/425M Level-B compliant
0.8 Vp-p, 75 Ω, 2.970 Gbps/2.967Gbps
• HD-SDI: SMPTE 292M compliant
0.8 Vp-p, 75 Ω, 1.485 Gbps/1.4835 Gbps
• SD-SDI: SMPTE 259M compliant
0.8 Vp-p, 75 Ω, 270 Mbps
3. REFERENCE
• BNC type
• HD: SMPTE 274M compliant
tri-level sync, 0.6 Vp-p, 75 Ω
• SD: Black burst signal (NTSC: 0.286 Vp-p, 75 Ω/
PAL: 0.3 Vpp, 75 Ω) or NTSC 10F-BB
4. PROMPTER
• BNC type
• Analog signals, 1.0 Vp-p, 75 Ω
Output Signals
5. CHARACTER /SYNC
• BNC type
• HD SYNC: BTA-S001 compliant
tri-level sync, 0.6 Vp-p, 75 Ω
• SD SYNC: composite sync，0.3 Vp-p, 75 Ω
• HD SYNC/SD SYNC selectable
• CHARACTER: VBS, 1 Vp-p, 75 Ω, character ON/OFF
selectable
6. HD/SD-SDI OUT 1 to 4
• BNC type
• HD-SDI: BTA-S004, SMPTE 292M compliant
0.8 Vp-p, 75 Ω, 1.485 Gbps/1.4835 Gbps
• SD-SDI: SMPTE 259M compliant
0.8 Vp-p, 75 Ω, 270 Mbps
• HD-SDI/SD-SDI selectable
7. 3G/HD-SDI OUT 1 to 3
• BNC type
• 3G-SDI: SMPTE 424M/425M Level-B compliant
0.8 Vp-p, 75 Ω, 2.970 Gbps/2.967Gbps
• HD-SDI: SMPTE 292M
0.8 Vp-p, 75 Ω, 1.485 Gbps/1.4835 Gbps
• 3G-SDI/HD-SDI selectable
8. HD TRUNK OUT
• BNC type
• HD-SDI: BTA-S004, SMPTE 292M compliant
0.8 Vp-p, 75 Ω, 1.485 Gbps/1.4835 Gbps (Available
only when camera single link format is selected)
9. AUDIO OUT CH1, CH2
12
3
- External View -
(0 dBu = 0.775 Vrms)
XLR 3-pin, Male
No. Signal I/O Specifications
1 MIC OUT (G) — +4 dBu/0 dBu/–20 dBu
2 MIC OUT (X) O
3 MIC OUT (Y) O
Input/Output Signals
10. CAMERA
• Optical/electrical connector
• VIDEO: Y/PB/PR
BTA-S004 compliant
3.7125 Gbps/3.7088 Gbps/1.485 Gbps /1.4835 Gbps
serial
• RET VIDEO: Y/PB/PR
3.7125 Gbps/3.7088 Gbps/1.485 Gbps /1.4835 Gbps
serial
• INTEERCOM: 2ch
• MIC: 2ch
• DIGITAL AUDIO (AES/EBU)
• CAMERA COMMAND
• PROMPTER: 1ch
HDCU2500 1-3

11. INTERCOM
- External View -
1
2
5
43
XLR 5-pin, Female
(0 dBu = 0.775 V rms)
Note
In the UNBALANCE mode, connect the GND signal of the
microphone to Pin 1
No. Signal I/O Specifications
1 INTERCOM
MIC IN (Y)/
(GND)
I –20 dBu (CARBON )
–40 dBu (ECM)
–60 dBu (DYNAMIC,
BALANCE/UNBAL-
ANCE)
2 INTERCOM
MIC IN (X)
I
3 GND — GND
4 INTERCOM L
OUT
O —
5 INTERCOM R
OUT
O —
12. RCP/CNU
17
6
5
4
3
2
8
- External View -
8-pin, Female
No. Signal I/O Specifications
1 TX (+) O SERIAL DATA OUT
2 TX (–) O
3 RX (+) I SERIAL DATA IN
4 RX (–) I
5 TX GND — GND for TX
6 POWER (+)
OUT
O RCP POWER, +30 V
7 POWER (–)
OUT
O GND for POWER
8 VIDEO (X) O 75 Ω, 1.0 V p-p
13. LAN
18
- External View -
8-pin, RJ-45, 10Base-T/100Base-TX
No. Signal I/O Specifications
1 TXD (+) O Transmitted Data (+)
2 TXD (–) O Transmitted Data (–)
3 RXD (+) I Received Data (+)
4 NC — No connection
5 NC — No connection
6 RXD (–) I Received Data (–)
7 NC — No connection
8 NC — No connection
14. NETWORK TRUNK
8-pin, RJ-45, 10Base-T/100Base-TX/1000Base-TX
- External View -
81
No. Signal I/O Specifications
1 TRD 0 (+) I/O Transmitted/Received
Data 0 (+)
2 TRD 0 (–) I/O Transmitted/Received
Data 0 (–)
3 TRD 1 (+) I/O Transmitted/Received
Data 1 (+)
4 TRD 2 (+) I/O Transmitted/Received
Data 2 (+)
5 TRD 2 (–) I/O Transmitted/Received
Data 2 (–)
6 TRD 1 (–) I/O Transmitted/Received
Data 1 (–)
7 TRD 3 (+) I/O Transmitted/Received
Data 3 (+)
8 TRD 3 (–) I/O Transmitted/Received
Data 3 (–)
15. TRUNK A
12-pin, Female
- External View -
A
B
C
D
J
K
LM
H
G
F
E
HDCU2500 1-4

No. RS422A RS232C Specifications
Signal I/O Signal I/O
A TX1 (–) O — — TRUNK Data out
B TX1 (+) O — —
C NC — NC — No connection
D TX0 (+) O TX1 O TRUNK Data out
E TX0 (–) O TX0 O
F RX0 (–) I RX0 I TRUNK Data in
G RX0 (+) I RX1 I
H RX1 (+) I — —
J RX1 (–) I — —
K GND — GND — GND for com-
mand
L NC — NC — No connection
M NC — NC — No connection
16. MIC REMOTE
D-sub, 15-pin, Female
- External View -
1
8
9
15
No. Signal I/O Specifications
1 +5.5 V OUT O Max. 250 mA
2 TALLY GND — GND for TALLY
3 G TALLY OUT O ON (GND) :
Max. 30 mA IN
4 R TALLY OUT O ON (GND) :
Max. 30 mA IN
5 CHU MIC AMP
GAIN CONT2
I Refer to “Specification
of CHU MIC AMP
GAIN”
6 CHU MIC AMP
GAIN CONT1
I
7 CHU MIC AMP
GAIN CONT0
I
8 MIC1 GAIN
CONT
ON/OFF IN
I Refer to “Specification
of MIC GAIN CONT”
9 GND — GND for +5.5 V
10 TALLY OUT O R/G/Y TALLY OUT
ON (GND) :
Max. 30 mA IN
11 Y TALLY OUT O ON (GND) :
Max. 30 mA IN
12 ASPECT RE-
MOTE
I L : REMOTE
Continued
No. Signal I/O Specifications
13 ASPECT CTL
CONT1
I Refer to “Specification
of ASPECT CTL”
14 ASPECT CTL
CONT2
(CNS MODE)
I
15 MIC2 GAIN
CONT
ON/OFF IN
I Refer to “Specification
of MIC GAIN CONT”
• Specification of CHU MIC AMP GAIN
Note
The following shows the MIC REMOTE settings in
OTHERS (M04) of the MAINTENANCE menu.
MIC1&2 or MIC+NETWORK: Common to MIC1 and
MIC2
MIC1, 2: MIC1
CONT0 CONT1 CONT2 CHU MIC AMP
GAIN
H H H 60 dB
L H H 50 dB
H L H 40 dB
L L H 30 dB
H H L 20 dB
• Specification of MIC GAIN CONT
8 pin 15 pin MIC GAIN CONT
L L MIC1 and MIC2 ON
L H MIC1 ON
H L MIC2 ON
H H INTERNAL set
HDCU2500 1-5

• Specification of ASPECT CTL
The following shows the MIC REMOTE settings in
OTHERS (M04) of the MAINTENANCE menu.
- For MIC REMOTE: MIC1, 2
CONT1 CONT2 ASPECT CTL
L H SQ (16 : 9)
H H EC (4 : 3)
L L INTERNAL set
H L LB
- For MIC REMOTE: MIC1, 2
Note
For specification of GAIN, refer to “Specification
of CHU MIC AMP GAIN”.
AMP GAIN of MIC2
12 pin: CONT2
13 pin: CONT1
14 pin: CONT0
- For MIC REMOTE: MIC+NETWORK
CONT (14 pin) CNS MODE
H MCS, BRIDGE, or LEGA-
CY
L Forcible LEGACY
Note
12 pin and 13 pin are no connection
17. INTERCOM/TALLY/PGM
25 14
113
- External View -
D-sub 25-pin, Female
(0 dBu = 0.775 Vrms)
No. Signal I/O Specifications
1 ENG (R) (X) OUT O ENG SYSTEM RE-
CEIVE
2 ENG (R) (Y) OUT O 0 dBu BALANCED
3 ENG (G) — GND for ENG
4 ENG (T) (X) IN I ENG SYSTEM
TALK
5 ENG (T) (Y) IN I 0 dBu BALANCED
6 PGM1 (X) IN I –20 dBu/0 dBu/+4
dBu
(Selectable with
CCU Menu)
7 PGM1 (Y) IN I
8 PGM1 (G) IN I
9 GND — GND for AUX
10 AUX3 — —
Continued
No. Signal I/O Specifications
11 R TALLY (X) IN I ON : 24 Vdc, TTL
(H), SHORT
OFF : 0 Vdc, TTL
(L), OPEN
12 R TALLY (Y) IN I
13 GND — CHASSIS GND
14 PROD (R) (X)
OUT
O PROD SYSTEM
RECEIVE 0 dBu
BALANCED
15 PROD (R) (Y)
OUT
O
16 PROD (G) — GND for PROD
17 PROD (T) (X) IN I PROD SYSTEM
TALK
0 dBu BALANCED
18 PROD (T) (Y) IN I
19 PGM2 (X) IN I –20 dBu/0 dBu/+4
dBu
(Selectable with
CCU Menu)
20 PGM2 (Y) IN I
21 PGM2 (G) IN —
22 Y TALLY (X) I ON : 24 Vdc, TTL
(H), SHORT
OFF : 0 Vdc, TTL
(L), OPEN
23 Y TALLY (Y) I
24 G TALLY (X) IN I ON : 24 Vdc, TTL
(H), SHORT
OFF : 0 Vdc, TTL
(L), OPEN
25 G TALLY (Y) IN I
1-3-2. Connector Input/Output Signals of
HKCU2007
Output Signals
1. SDI OUT 1 to 4
• BNC type
• 3G-SDI: SMPTE 424M/425M Level-B compliant
0.8 Vp-p, 75 Ω, 2.970 Gbps/2.967Gbps
• HD-SDI: BTA-S004, SMPTE 292M compliant
0.8 Vp-p, 75 Ω, 1.485 Gbps/1.4835 Gbps
• 3G-SDI/HD-SDI selectable
• Character ON/OFF selectable (connectors 3/4)
1-3-3. Connector Input/Output Signals of
HKCU1001
Output Signals
1. VBS 1, 2
• BNC type
• VBS 1.0 V p-p, 75 Ω
2. PIX OUT
• BNC type
HDCU2500 1-6