SUTO S450 Manual

English
Instruction and Operation Manual
S450
Thermal Mass Flow Meter
for Heavy Duty
and x Applications
(Insertion)

Dear Customer,
Thank you for choosing our product.
Please read this manual in full before starting up the device and
carefully observe the instructions stated. The manufacturer cannot be
held liable for any damage which occurs as a result of non-observance
or non-compliance with this manual.
Should the device be tampered with in any manner other than a
procedure which is described and specified in the manual, the warranty
is void and the manufacturer is e empt from liability.
The device is destined e clusively for the described application.
SUTO offers no guarantee for the suitability for any other purpose.
SUTO is also not liable for consequential damage resulting from the
delivery, capability or use of this device.
2 S450

Table of Contents
1 Safety instructions......................................................................4
2 Registered trademarks.................................................................6
3 Application.................................................................................7
4 Features....................................................................................7
5 Technical data.............................................................................8
5.1 General................................................................................8
5.2 Electrical data.......................................................................9
5.3 Output signals......................................................................9
5.4 Accuracy .............................................................................9
5.5 Flow ranges........................................................................10
6 Dimensional drawing..................................................................11
7 Determine the installation point..................................................12
7.1 Inlet and outlet sections.......................................................12
8 Installation ..............................................................................14
8.1 Installation requirements......................................................15
8.2 Installation procedure .........................................................15
8.2.1 Determine the insertion depth.........................................15
8.2.2 Install the Flow Meter.....................................................16
8.2.3 Removing the Flow Meter ...............................................18
8.3 Electrical connection............................................................18
8.3.1 Connection diagram.......................................................19
8.3.2 Pin assignment..............................................................19
9 Signal outputs..........................................................................21
9.1 Analog and pulse outputs ....................................................21
9.1.1 Analog output...............................................................21
9.1.2 Pulse output..................................................................21
9.2 HART output ......................................................................22
9.3 Modbus Interface ................................................................23
9.4 M-Bus output .....................................................................26
9.5 Connection between S450 Outputs and Customer Equipment....26
10 Information on the Display.......................................................29
10.1 Startup.............................................................................29
10.2 Data and Signs..................................................................30
11 Configuration..........................................................................31
12 Optional accessories................................................................34
12.1 Display.............................................................................34
12.2 Service kit........................................................................34
13 Calibration..............................................................................35
14 Maintenance...........................................................................35
15 Disposal or waste....................................................................35
S450 3

1 Safety instructions
1 Safety instructions
Please check if this instruction manual matches the
product type.
Please observe all notes and instructions indicated in this
manual. It contains essential information which must be
observed before and during installation, operation and
maintenance. Therefore this instruction manual must be read carefully
by the technician as well as by the responsible user or qualified
personnel.
This instruction manual must be available at the operation site of the
flow meter at any time. In case of any obscurities or questions,
regarding this manual or the product, please contact the manufacturer.
WARNING!
Compressed air!
Any contact with quickly escaping air or bursting
parts of the compressed air system can lead to
serious injuries or even death!
•Do not e ceed the ma imum permitted pressure range (see
sensors label).
•Only use pressure tight installation material.
•Avoid that persons get hit escaping air or bursting parts of the
instrument.
•The system must be pressureless during maintenance work.
WARNING!
Voltage used for supply!
Any contact with energized parts of the product, may
lead to an electrical shock which can lead to serious
injuries or even death!
•Consider all regulations for electrical installations.
•The system must be disconnected from any power supply during
maintenance work.
•Any electrical work on the system is only allowed by authorized
qualified personal.
4 S450

1 Safety instructions
ATT NTION!
Permitted operating parameters!
Observe the permitted operating parameters, any
operation exceeding this parameters can lead to
malfunctions and may lead to damage on the
instrument or the system.
•Do not e ceed the permitted operating parameters.
•Make sure the product is operated in its permitted limitations.
•Do not e ceed or undercut the permitted storage and operation
temperature and pressure.
•The product should be maintained and calibrated frequently, at
least annually.
General safety instructions
•It is allowed to use the product in e plosive areas. Please contact
the manufacturer.
•Please observe the national regulations before/during installation
and operation.
Remarks
•It is not allowed to disassemble the product.
•Always use spanner to mount the product properly.
ATT NTION!
Measurement values can be affected by malfunction!
The product must be installed properly and
frequently maintained, otherwise it may lead to
wrong measurement values, which can lead to
wrong results.
•Always observe the direction of the flow when installing the flow
meter. The direction is indicated on the housing.
•Do not e ceed the ma imum operation temperature at the sensors
tip.
•Avoid condensation on the sensor element as this will affect the
accuracy enormously.
S450 5

1 Safety instructions
Storage and transportation
•Make sure that the transportation temperature of the flow meter
without display is between -30 ... +70°C and with display between
-10 ... +60°C.
•For transportation it is recommended to use the packaging which
comes with the flow meter.
•Please make sure that the storage temperature of the flow meter
is between -10 ... +50°C.
•Avoid direct UV and solar radiation during storage.
•For the storage the humidity must be <90% with no condensation.
2 Registered trademarks
SUTO®Registered trademark of SUTO iTEC
MODBUS®Registered trademark of the Modbus Organization,
Hopkinton, USA
Android™,
Google Play
Registered trademarks of Google LLC
6 S450

3 Application
3 Application
The S450 Thermal Mass Flow Meter is designed for the e plosive areas
and is mainly used to measure compressed air and process gases in
industrial environments.
The S450 can measure the following parameters for the compressed air
or gases:
•Velocity
•Volume flow
•Total consumption
The default factory settings are: Velocity in m/s, Volume flow in m3/h
and Total Consumption in m3. Other units can be programmed by the
optional display or the service kit.
4 Features
•Direct measurement of mass flow and standard flow without the
need of pressure and temperature compensation.
•Insertion type for bigger pipes.
•No moving parts, no clogging.
•All sensor parts which come into contact with the measurement
medium are made of stainless steel 316L.
•Robust metal enclosure suitable for outdoor applications in harsh
environments.
•Wireless Bluetooth interface for onsite settings.
•Optional display showing flow rate, consumption, medium
temperature and diagnostic result.
S450 7

5 Technical data
5 Technical data
5.1 General
Measuring range 0.4 ... 92.7 sm/s (standard range calibration)
0.8 ... 185 sm/s (ma range calibration)
1.0 ... 224 sm/s (high speed calibration)
(See Section 4.5 for flow measurement ranges
in different tube diameters)
* sm/s: standard meter per second
Parameters Standard unit flow: m3/h
Available units: m3/min, l/min, l/s, cfm,
kg/h, kg/min, kg/s
Standard velocity
unit:
m/s
Reference conditions ISO1217, 20 °C, 1000 mbar (Standard-Unit)
DIN1343, 0 °C, 1013.25 mbar (Norm-Unit)
Principle of
measurement
Thermal mass flow
Sensor Resistive sensor
Measured medium Air, gas (non corrosive gas)
Operating temperature -40 ... +150°C (Medium temperature)
-40 ... +65°C (Ambient temperature)
Humidity of the meas.
medium
< 90%, no condensation
Operating pressure 0 ... 1.6 MPa (Applicable for the option A1280)
0 ... 5.0 MPa (Applicable for the option A1279)
Note: For pressure above 1.5 MPa you need
to use the installation device A530 1106 or
A530 1113.
Housing material Al alloy
Material of the probe
tube, sensor head and
screwing
Stainless steel 1.4404 (SUS 316L)
Protection class IP67
8 S450

5 Technical data
Dimensions See dimensional drawing on the ne t page
Display (optional) 128 64
Tube diameter From DN15 (1/2”) upwards
Screwing thread G1/2” (ISO 228/1)
Weight 1.75 kg (220 mm version)
5.2 lectrical data
Power supply 16 ... 30 VDC, 5 W
5.3 Output signals
Analog output See section 9.1.1
Pulse output See section 9.1.2
HART output See section 9.2
Modbus output See section 9.3
M-Bus output See section 9.4
5.4 Accuracy
Accuracy* ±(1.5% of reading + 0.3% full scale)
Repeatability 0.25% of reading
Stated accuracy at Ambient/process temperature 23°C±3°C
Ambient/process humidity <90%
Process pressure at 0.6 MPa
* The specified accuracy is valid only within the minimum and ma imum
flow rates that are stated in section 5.5.
S450 9

5 Technical data
5.5 Flow ranges
The flow ranges are stated under the following conditions:
•Standard flow in air
•Reference pressure: 1000 hPa
•Reference Temperature: +20°C
Inch DN S-Range (m3/h) M-Range (m3/h) HS-Range (m3/h)
½” DN15 0.2 ... 45.6 0.4 ... 91.0 0.48 ... 110
¾” DN20 0.4 ... 89.1 0.9 ... 178 1.09 ... 215
1” DN25 0.6 ... 148 1.2 ... 295 1.82 ... 357
1½” DN40 1.5 ... 367 2.9 ... 732 4.36 ... 886
2” DN50 2.4 ... 600 4.8 ... 1,198 7.26 ... 1,450
2½” DN65 4.1 ... 1,027 8.2 ... 2,049 12.1 ... 2,480
3” DN80 5.7 ... 1,424 11.4 ... 2,841 16.9 ... 3,442
4” DN100 8.7 ... 2,183 17.4 ... 4,357 24.2 ... 5,276
5” DN125 20 ... 3,420 38 ... 6,824 45.9 ... 8,263
6” DN150 20 ... 4,930 39 ... 9,839 70.2 ... 11,913
8” DN200 35 ... 8,786 70 ... 17,533 106 ... 21,229
10” DN250 55 ... 13,744 110 ... 27,429 166 ... 33,211
12” DN300 79 ... 19,815 158 ... 39,544 220 ... 47,880
Remarks:
•To calculate flow ranges based on pipe and reference conditions in
your site, download and install the "Flow range calculator" tool for
free from http://www.suto-itec.com.
•To fast access the tool download page, enter "flowrange" (without
spaces) in the search field, and click the tool in the search result.
•The total consumption value is saved to the permanent memory
every 5 minutes. If within these 5 minutes the device is powered
off, it will restore the last consumption value which was saved in
the last cycle.
10 S450