Teknik 5158097 User manual

www.teknikoffice.co.uk
Get crafty.
Hideaway Office/Craft Station
Model 5158097
Teknik

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
2-3
4-5
6-24
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D FIXED SHELF (1)
E BOTTOM (1)
F BACK (1)
G2 RIGHT DOOR (1)
H2 LEFT DOOR (1)
I PULL-OUT TOP (1)
J3 PULL-OUT BACK (1)
K FLIP-UP TOP (1)
L OUTER UPRIGHT (2)
M INNER UPRIGHT (2)
N SHELF UPRIGHT (1)
O SLIDING SHELF (1)
P SLIDING SHELF BACK (1)
Q ADJUSTABLE SHELF (6)
R LEG (1)
S FRONT MOLDING (1)
T RIGHT MOLDING (1)
U LEFT MOLDING (1)
V LEG STOP (1)
Page 2
Now you know
our ABCs.
Part Identification

åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Part Identification
Page 3
A
B
C
D
E
F
G2
H2
I
J3
K
L
L
M
M
N
O
P
Q
Q
Q
Q
Q
Q
R
S
T
U
V

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
87K KNOB - 2
LEVELER - 4
18E
PROPEL NUT - 4
14M
MAGNETIC CATCH - 1
1I
GROMMET CAP - 1
1P
11F TWIST-LOCK®
FASTENER - 14
FLIP-UP TOP
HINGE - 2
16H
MOLDING
CONNECTOR - 2
16F HINGE - 4 30H
(EXTENSION SET SHOWN SEPARATED)
LOCKING EXTENSION
SLIDE - 2
ZY LOCKING EXTENSION
RAIL - 2
CASTER - 2
15C
35AW CABINET RIGHT - 1 35AY DRAWER RIGHT - 1 35AZ DRAWER LEFT - 1
35AX CABINET LEFT - 1
16C CASTER BRACKET - 2
Page 4
OUTLET - 1
1D
(EXTENSION SET SHOWN SEPARATED)
EXTENSION SLIDE - 2
40MC
EXTENSION RAIL - 2
40MA
17E LEVELER BRACKET - 4
NAIL - 46
1N
STRIKE PLATE - 2
6I

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
BLACK 9/16" LARGE HEAD SCREW - 10
1S
SILVER 1-1/4" PAN HEAD SCREW - 2
45S
BLACK 1-1/4" FLAT HEAD SCREW - 6
7S
GOLD 9/16" LARGE HEAD SCREW - 16
5S
BLACK 1-5/8" PAN HEAD SCREW - 6
27S
BLACK 1-7/8" FLAT HEAD SCREW - 9
2S
SILVER 2" FLAT HEAD SCREW - 5
57S
BROWN 1" FLAT HEAD SCREW - 4
18S
CORD CLIP - 1
4P
BLACK 2" PAN HEAD SCREW - 4
66S
GOLD 5/16" FLAT HEAD SCREW - 16
3S
SCREW COVER - 4
16P METAL PIN - 24 1R
BLACK 1/2" FLAT HEAD SCREW - 2
11S
GROMMET - 1
10P RUBBER SLEEVE - 24
2R
Page 5
SILVER 5/8" FLAT HEAD SCREW - 4
23S

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push a SAUDER TWIST-LOCK®
FASTENER (11F) into the large holes in the FIXED
SHELF (D) and BOTTOM (E).
å Repeat this step for the OUTER UPRIGHTS (L) and
SHELF UPRIGHT (N).
Page 6
(14 used)
11F
Do not tighten the TWIST-LOCK® FASTENERS in this step.
11F
D
E

å Tap two MOLDING CONNECTORS (16F) into the notches
in the MOLDINGS (S, T and U).
Step 2
Page 7
Flat end
Flat end
S
T
U
Use your hammer to tap the MOLDING CONNECTORS (16F) into the notches in the MOLDINGS.
Unfinished surface
Unfinished surface
16F
16F
Just think. The sooner
you do this, the sooner
you do something else.

Finished edge
Step 3
Page 8
å Separate the LOCKING EXTENSION SLIDES (Z) from the LOCKING EXTENSION RAILS (Y) as shown in the upper
diagram below. Be prepared, the parts are greasy.
å Fasten the LOCKING EXTENSION RAILS (Y) to the ENDS (A and B). Use four GOLD 5/16" FLAT HEAD SCREWS (3S).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram. Then, slide the inner cartridge
of the EXTENSION RAIL in to find the other hole that lines up with the hole in the END. Turn a SCREW into this hole.
å Fasten the CABINET RIGHT (35AW) to the RIGHT END (A) and the CABINET LEFT (35AX) to the LEFT END (B). Use four
GOLD 5/16" FLAT HEAD SCREWS (3S) through the first and second holes from the roller end in the RAIL and into the
holes of your choice in the ENDS.
å Now, insert the CORD CLIP (4P) into the hole in the RIGHT END (A). The CORD CLIP is used to hold your ELECTRICAL
OUTLET cord in place.
Open end
Open end
Push the silver tab in and pull the SLIDE from the RAIL.
4P
A
B
Y
Y
Y
Z
Finished edge
GOLD 5/16" FLAT HEAD SCREW
(8 used in this step)
3S
Roller end
Roller end

Step 4
Page 9
å Fasten the LEFT MOLDING (U) to the LEFT END (B). Use two
BLACK 2" PAN HEAD SCREWS (66S).
å Fasten the FIXED SHELF (D) and BOTTOM (E) to the LEFT
END (B). Tighten four TWIST-LOCK® FASTENERS.
How to use the SAUDER TWIST-LOCK®FASTENER
1. Insert the dowel end of the FASTENER into the
hole of the adjoining part.
NOTE: The dowel end of the FASTENER must
remain fully inserted in the hole of the adjoining
part while locking the FASTENER.
2. Tighten the FASTENER with a Phillips
screwdriver as tight as possible.
Finished edge
Finished edge
Finished edge
Unfinished surface
Surface with
TWIST-LOCK®
FASTENERS
Finished surface
B
D
E
S
U
Dowel end
BLACK 2" PAN HEAD SCREW
(2 used in this step)
66S
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution

å Fasten the SHELF UPRIGHT (N) to the FIXED SHELF (D).
Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S) as
shown in the upper diagram.
å Fasten the RIGHT END (A) to the FIXED SHELF (D) and
BOTTOM (E). Tighten four TWIST-LOCK® FASTENERS as
shown in the lower diagram.
å Fasten the RIGHT MOLDING (T) to the RIGHT END (A).
Use two BLACK 2" PAN HEAD SCREWS (66S).
Step 5
Page 10
D
D
N
BLACK 1-7/8" FLAT HEAD SCREW
(2 used for the SHELF UPRIGHT)
2S
Finished edge
Finished edge
A
BLACK 2" PAN HEAD SCREW
(2 used for the RIGHT END)
66S
T
E
Surface without
TWIST-LOCK®
FASTENERS