Teknik Hampstead 5426504 User manual

Hampstead Park Lift Up Table
Model 5426504
Guaranteed to hold
other beverages, too.
Teknik
www.teknikoffice.co.uk

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
No. 2 Phillips Screwdriver
Tip Shown Actual Size
3
4
5-19
Adjustable Wrench
Page 2
Tape Measure

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C STRETCHER (1)
D LOUVERED PANEL (2)
E SHELF (1)
F UPRIGHT (1)
G BASE (2)
H TOP (1)
J BOTTOM (1)
A
B
C
D
D
E
F
G
G
H
J
Page 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
CAM SCREW - 6
8F WOOD DOWEL - 4 15F
HIDDEN CAM - 18
1F CAM DOWEL - 12 2F
BLACK 9/16" LARGE HEAD SCREW - 36
1S 52S SILVER 3/4" PAN HEAD SCREW - 2
BLACK 3/4" MACHINE SCREW - 4
92S BLACK 1-1/4" MACHINE SCREW - 4 93S
SUPPORT BRACKET - 2
37G BLACK WASHER - 8
13M
METAL
BRACKET - 10
4G BUMPER - 4
2M
74M LIFT TABLE
MECHANISM SET - 1
NUT - 8
24M SILVER WASHER - 2 80M BUSHING - 2
91M
BLACK 1-15/16" FLAT HEAD SCREW - 4
113S
Page 4

Hardware Usage Guide
HOW TO USE A HIDDEN CAM & CAM DOWEL
Cam Screw
Hidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2. 3.
1
2
Insert the CAM SCREW into the HIDDEN CAM.
Tighten the HIDDEN CAM.
HOW TO USE A HIDDEN CAM & CAM SCREW
Turn the CAM SCREW until
the shoulder is against the
surface of the part.
1.
2. Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
1. Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the edge
of the board.
Hole
Arrow
Metal end
Hidden Cam
Cam Dowel
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
3.
Page 5

Step 1
å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
å Push four HIDDEN CAMS (1F) into the short edges of the SHELF (E). Then, insert the metal end of a CAM DOWEL (2F)
into each HIDDEN CAM.
å Push six HIDDEN CAMS (1F) into the long edges of the SHELF (E).
Do not tighten the HIDDEN CAMS in this step.
Arrow
1F
2F
Metal end
Arrow
1F
2F
Metal end
1F
Arrow
1F
Arrow
E
Page 6

å Push four HIDDEN CAMS (1F) into the LOUVERED PANELS (D). Then, insert the metal end of a CAM DOWEL (2F) into
each HIDDEN CAM.
å Turn six CAM SCREWS (8F) into the LOUVERED PANELS (D).
å Fasten the LOUVERED PANELS (D) to the SHELF (E). Tighten six HIDDEN CAMS.
Step 2
Arrow
1F
2F
Metal end
Arrow
1F
2F
Metal end 8F
D
D
D
E
Surface with HIDDEN CAMS
D
Page 7
These surfaces
should be even.

å Fasten the UPRIGHT (F) to the SHELF (E). Use two
BLACK 1-15/16" FLAT HEAD SCREWS (113S).
Step 3
Surface with
HIDDEN CAMS
F
E
Page 8
BLACK 1-15/16" FLAT HEAD SCREW
(2 used in this step)
113S

å Push four HIDDEN CAMS (1F) into the BOTTOM (J). Then,
insert the metal end of a CAM DOWEL (2F) into each
HIDDEN CAM.
Step 4
Arrow
1F
2F
Metal end
Arrow
1F
2F
Metal end
Page 9
J
Meet Part (J). This component has
been engineered to be lighter, stronger,
faster… well ok. Not technically faster. But
definitely makes for a sturdier Lift-Top
Coee Table that’s easier to assemble
and friendlier to the environment.

å Fasten ten METAL BRACKETS (4G) to the BASES (G). Use ten BLACK 9/16" LARGE HEAD SCREWS (1S).
å NOTE: Be sure the BRACKETS are even with the edges of the BASES.
å Fasten the BASES (G) to the BOTTOM (J). Use six BLACK 9/16" LARGE HEAD SCREWS (1S).
Step 5
BLACK 9/16" LARGE HEAD SCREW
(16 used in this step)
1S
4G
4G
4G
G
G
G
G
J
Page 10
(10 used)
Surface with BRACKETS
Surface without BRACKETS