Teknik Barrister Home 5418891 User manual

www.teknikoffice.co.uk
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Barrister Home Wardrobe
Barrister Home Collection | Model 5418891
You could use a new
hide-and-seek spot.
Teknik

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
2-3
4-5
6-28
A RIGHT END (1)
B LEFT END (1)
C LOWER END (2)
D TOP (1)
E BOTTOM (1)
F SHELF (1)
G LARGE BACK (1)
H BACK (1)
I LOWER RIGHT SUPPORT (1)
J LOWER LEFT SUPPORT (1)
K DOOR (2)
L BRACE (1)
M ADJUSTABLE SHELF (1)
N BASE (1)
O RIGHT BASE (1)
P LEFT BASE (1)
Q DRAWER FRONT (1)
R FRONT MOLDING (1)
S RIGHT MOLDING (1)
T LEFT MOLDING (1)
U END MOLDING (2)
V SHELF MOLDING (1)
W SIDE MOLDING (2)
X LOWER END MOLDING (2)
D28 DRAWER RIGHT SIDE (1)
D29 DRAWER LEFT SIDE (1)
D483 DRAWER BACK (1)
D998 DRAWER BOTTOM (1)
M65 DRAWER BRACE (1)
Now you know
our ABCs.
Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
Pae 2

Now you know
our ABCs.
Part IdentificationPart Identification
Pae 3
A
B
C
D
E
F
G
HI
J
K
L
M
N
O
PQ
R
S
T
U
V
W
D28
K
D29
D483
D998
M65
C
W
U
X
X

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Pae 4
5L WARNING LABEL - 1
(Refer to Step 21 for proper
location and application)
WARNING
Serious or fatal crushing injuries can occur
from furniture tip-over. To help prevent
tip-over:
• Place heaviest items in the lowest drawers.
• Unless specifically desined to accommodate, do not
set TVs or other heavy objects on top of this product.
• Never allow children to climb or han on drawers,
doors, or shelves.
• Never open more than one drawer at a time.
• If equipped with a drawer interlock system, do not
defeat or remove it.
Use of tip-over restraints may only reduce, but not
eliminate, the risk of tip-over.
This is a permanent label. Do not attempt to remove!
04/10 332296
31G CORNER BRACKET - 4
40DC40DA UNIVERSAL CABINET RAIL - 2 DRAWER RIGHT - 1 40DD DRAWER LEFT - 1
Locate this nylon SAFETY
STRAP (60M) to be used
later in assembly. Do not
accidentally throw away.
SAFETY
STRAP - 1
60M SAFETY DRYWALL
ANCHOR - 1
61M
WASHER - 1
13M
7A ROD HANGER - 2
10A SLIDE CAM - 2
MAGNETIC CATCH - 4
2I
CAM SCREW - 24
8F
WOOD DOWEL - 8
15F
STRIKE PLATE - 4
6I
HIDDEN CAM - 32
1F CAM DOWEL - 8 2F
KNOB - 2
69K PULL - 2
70K
33M DECORATIVE
END - 4 34M DECORATIVE
BACKPLATE - 2
27H HINGE - 6
ROD - 1
20A
82M DECORATIVE
POST - 4
METAL BRACKET - 4
4G

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Pae 5
SILVER 3/4" MACHINE SCREW - 4
20S
BLACK 9/16" LARGE HEAD SCREW - 57
1S BLACK 1-7/8" FLAT HEAD SCREW - 8 2S
BLACK 7/8" MACHINE SCREW - 4
37S
CAM COVER - 12
13P
12S BROWN 1" FLAT HEAD SCREW - 4
3S GOLD 5/16" FLAT HEAD SCREW - 8
METAL PIN - 4
1R
BLACK 1/2" FLAT HEAD SCREW - 4
11S
BLACK 9/16" FLAT HEAD SCREW - 6
32S
SILVER 1/2" FLAT HEAD SCREW - 2
78S
NAIL - 64
1N
SILVER 1-1/2" MACHINE SCREW - 2
95S
RUBBER SLEEVE - 4
2R
30S BLACK 1-9/16" FLAT HEAD SCREW - 5

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Push thirty-two HIDDEN CAMS (1F) into the ENDS (A, B,
and C), TOP (D), BOTTOM (E), SHELF (F), LOWER
SUPPORTS (I and J), and DRAWER BRACE (M65). Then,
insert the metal end of a CAM DOWEL (2F) into each
HIDDEN CAM except for the ENDS, TOP, and BOTTOM.
Pae 6
Arrow
1F
2F
Do not tihten the HIDDEN
CAMS in this step.
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
(8 used)
A
B
C
D
E
F
M65
C
I
J
The arrow in the HIDDEN
CAM must point toward the
hole in the ede of the board.
Hole
(32 used)
Arrow
Arrow
1F
Do not insert
CAM DOWELS
into these parts.
Do not insert
CAM DOWELS
into these parts.

Step 2
Pae 7
8F
å Turn twenty-four CAM SCREWS (8F) into the BASES (O
and P), MOLDINGS (S and T), and END MOLDINGS (U and X).
O
P
S
T
U
X
X
U
8F
8F
(24 used)
Be sure to position the
LOWER END MOLDINGS (X)
as shown and insert the CAM
SCREWS (8F) into the exact
holes shown.

Step 3
Pae 8
S
T
U
U
A
B
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
å Fasten the MOLDINGS (S and T) and END MOLDINGS (U)
to the ENDS (A and B). Tihten twelve HIDDEN CAMS.
å Fasten the ROD HANGERS (7A) to the ENDS (A and B).
Use two SILVER 1/2" FLAT HEAD SCREWS (78S).
12
Remember:
Rihty tihty.
Lefty loosey.
7A
SILVER 1/2" FLAT HEAD SCREW
(2 used in this step)
78S
(2 used)
These holes
must be here.
Surface with
CAM SCREWS
Wide ede
Wide ede

Step 4
Pae 9
å Fasten the UNIVERSAL CABINET RAILS* (40DA) to the
LOWER SUPPORTS (I and J). Use four GOLD 5/16" FLAT
HEAD SCREWS (3S) throuh holes #1 and #4.
å *patent pendin lide system
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
3
2
1
1
2
3
4
4
I
J
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Glide end
Finished ede
Finished ede
Glide end

å Fasten the METAL BRACKETS (4G) and CORNER
BRACKETS (31G) to the TOP (D) and BOTTOM (E). Use
twelve BLACK 9/16" LARGE HEAD SCREWS (1S).
Step 5
Pae 10
D
E
BLACK 9/16" LARGE HEAD SCREW
(12 used in this step)
1S
31G
31G
(4 used)
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
4G