Teknik Hudson Chunky Desk 5425833 User manual

Hudson Chunky Desk
Model 5425833
Sit and surf.
Teknik
www.teknikoffice.co.uk

Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
Skip the power trip.
This time.
3
4
5-18
19-21
22-24
25-26
27
Page 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A LEFT END (1)
B RIGHT END (1)
C UPRIGHT (1)
D TOP (1)
E BOTTOM (1)
F ADJUSTABLE SHELF (1)
G DOOR (1)
H VALANCE (1)
J MODESTY PANEL (1)
K BACK (1)
L SKIRT (1)
Page 3
A
B
C
D
E
F
G
H
J
K
L

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 4
SILVER 1/2" PAN HEAD SCREW - 4
9
5BUMPER CARD - 1
SHELF PIN - 4
4
6HINGE - 2 BROWN
APPLIQUE - 8
7WHITE
APPLIQUE - 10
8
SILVER 5/8" FLAT HEAD SCREW - 4
10
CAM SCREW - 22
2
HIDDEN CAM - 22
1WOOD DOWEL - 30 3

Hardware Usage Guide
HOW TO USE A HIDDEN CAM & CAM SCREW OR CAM DOWEL
NOTE: Various CAM SCREWS or a CAM DOWEL may be used.
Cam Screws Cam Dowel
Turn the CAM SCREW or
gently tap the CAM DOWEL
until the shoulder is against
the surface of the part.
1.
Hidden CamHidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2.
3.
1
2
Insert the CAM SCREW or CAM DOWEL into the
HIDDEN CAM. Tighten the HIDDEN CAM.
Page 5

Step 1
å Assemble your unit on a carpeted floor or on the
empty carton to avoid scratching your unit or the floor.
å Push eight HIDDEN CAMS (1) into the UPRIGHT (C)
and BACK (K).
å Turn four CAM SCREWS (2) into the exact holes shown
in the UPRIGHT (C).
å Insert eight WOOD DOWELS (3) into the remaining
holes in the UPRIGHT (C).
Page 6
1
C
K
1
Arrow Arrow
Arrow
2
1
3
(8 used)

å Fasten the BACK (K) to the UPRIGHT (C). Tighten two
HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the UPRIGHT
insert into the BACK.
Step 2
Page 7
C
K
Edge with
HIDDEN CAMS
Surface with HIDDEN CAMS

å Push four HIDDEN CAMS (1) into the BOTTOM (E).
å Fasten the BOTTOM (E) to the UPRIGHT (C). Tighten two
HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the UPRIGHT
insert into the BOTTOM.
Step 3
Page 8
C
E
E
Arrow
Surface with
HIDDEN CAMS
Unfinished edge
1
1
Arrow

å Place the VALANCE (H) and SKIRT (L) onto the WOOD
DOWELS in the UPRIGHT (C) as shown.
å NOTE: The VALANCE (H) is wider than the SKIRT (L).
Step 4
Page 9
L
H
C
Finished edge
Unfinished edge
These edges
should be even.
Just think. The sooner
you do this, the sooner
you do something else.

å Push two HIDDEN CAMS (1) into the RIGHT END (B).
å Turn four CAM SCREWS (2) into the RIGHT END (B).
å Insert eight WOOD DOWELS (3) into the RIGHT END (B).
å Carefully flip the RIGHT END (B) over.
å Fasten the RIGHT END (B) to the BOTTOM (E) and
BACK (K). Tighten four HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the RIGHT END
insert into the BOTTOM (E), VALANCE (H), BACK (K),
and SKIRT (L).
Step 5
Page 10
3
F
L
I
P
O
V
E
R
B
B
E
L
H
K
(8 used)
2
1
Arrow