Teknik Canal Heights 5419228 User manual

www.teknikoffice.co.uk
The stories of your life.
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Canal Heights 4 Shelf Bookcase
Model 5419228
Teknik

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
3
4
5-10
Page 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D SHELF (4)
E SHELF SUPPORT (4)
F BACK SUPPORT (2)
A
B
C
D
D
D
D
E
E
E
E
F
F
Page 3
www.sauder.com419228

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
1/2" MACHINE SCREW - 20
6
1-1/4" FLAT HEAD SCREW - 20
3
Page 4 www.sauder.com 419228
9/16" LARGE HEAD SCREW - 6
7FURNITURE TIPPING RESTRAINT KIT - 1
99

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Fasten the ENDS (A and B) to the SHELF SUPPORTS (E).
Use sixteen 1/2" MACHINE SCREWS (6).
Page 5
A
B
These holes must be here.
These holes must be here.
1/2" MACHINE SCREW
(16 used in this step)
6
6
6
These holes must be here.
6
6
E
E
E
E

å Fasten the SHELVES (D) to the SHELF SUPPORTS (E)
and ENDS (A and B). Use twenty 1-1/4" FLAT
HEAD SCREWS (3).
Step 2
Page 6
1-1/4" FLAT HEAD SCREW
(20 used in this step)
3
3
3
3
3
3
3
3
3
3
Surface
with holes
Surface
with holes
Surface
with holes
Surface
with holes
A
B
D
D
D
D
E
E
E
E

å Fasten the BACK SUPPORTS (F) to the ENDS (A and B).
Use four 1/2" MACHINE SCREWS (6).
Step 3
Page 7
1/2" MACHINE SCREW
(4 used in this step)
6
A
B
F
F

å Fasten the TOP (C) to the ENDS (A and B). Use six 9/16"
LARGE HEAD SCREWS (7).
Step 4
419228
7
Edge without molding
A
B
C
For support, place packing foam and
magazines here under both ENDS to lift
your unit so the TOP is easier to attach.
9/16" LARGE HEAD SCREW
(6 used in this step)
7

Step 5
419228
C
å Carefully stand your unit upright.
å We recommend using the FURNITURE TIPPING RESTRAINT KIT (99) for added
stability. Fasten a bracket to the TOP (C) using the 5/8" screw as shown.
å Place your unit in its final location against a wall.
å Follow the instructions included in the KIT to fasten your unit to the wall.
99
Use the 5/8" screw through the
small hole in a bracket and into
the back edge of the TOP (C).
Small hole

Step 6
Page 10
40 lbs.
40 lbs.
40 lbs.
40 lbs.
No load
å NOTE: Please read the back pages of the instruction booklet for
important safety information.
å This completes assembly. Clean with your favorite furniture polish
or a damp cloth. Wipe dry.