Teknik Home Study 5426055 User manual

Home Study Lift Up Coffee/Work Table
Model 5426055
It's addicting.
Teknik
www.teknikoffice.co.uk

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
3
4
5-29
30-33
34-37
38
39
Page 2
Adjustable Wrench
Short Screwdriver

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D SHELF (1)
E BOTTOM (1)
F STRETCHER (1)
G RIGHT FRONT/LEFT REAR LEG (2)
J LEFT FRONT/RIGHT REAR LEG (2)
L SHORT SKIRT (2)
M LONG SKIRT (2)
N END MOLDING (4)
O UPRIGHT (1)
P BRACE (1)
Q FRONT PANEL (1)
R BACK PANEL (1)
Page 3
A
B
C
D
E
F
G
J
J
G
L
M
N
O
P
Q
R
L
N
N
N
M

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
APPLIQUE
CARD - 5
100P
BLACK 9/16" LARGE HEAD SCREW - 16
1S
HIDDEN
CAM - 26
1F CAM
SCREW - 26
8F
SMALL METAL
WASHER - 8
13M NUT - 8
24M
BUMPER - 6
2M
SUPPORT
BRACKET - 2
37G
BLACK 3/4" MACHINE SCREW - 4
92S BLACK 1-1/4" MACHINE SCREW - 4 93S
23M LIFT TABLE
MECHANISM SET - 1
BLACK 1-15/16" FLAT HEAD SCREW - 6
113S
BLACK 3/4" PAN HEAD SCREW - 2
85S
BUSHING - 2
91M
PLASTIC
WASHER - 2
10I
SILVER 1/4" MACHINE SCREW - 2
61S
METAL
PIN - 2
1R
BLACK 9/16" FLAT HEAD SCREW - 8
32S
LARGE METAL
WASHER - 2
80M
PULL - 2
22K
WOOD
DOWEL - 4
15F11F TWIST-LOCK®
FASTENER - 10
Page 4

Hardware Usage Guide
1. Insert the dowel end of the FASTENER into the
hole of the adjoining part.
NOTE: The dowel end of the FASTENER must
remain fully inserted in the hole of the adjoining
part while locking the FASTENER.
2. Tighten the FASTENER with a Phillips
screwdriver as tight as possible.
Dowel end
2.
Push a TWIST-LOCK® FASTENER
into the large hole in the part.
1.
HOW TO USE A TWIST-LOCK®FASTENER
Page 5
Cam Screw
Hidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2. 3.
1
2
Insert the CAM SCREW into the HIDDEN CAM.
Tighten the HIDDEN CAM.
HOW TO USE A HIDDEN CAM & CAM SCREW
Turn the CAM SCREW until
the shoulder is against the
surface of the part.
1.

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push eight SAUDER TWIST-LOCK®
FASTENERS (11F) into the large holes in the SHELF (D)
and FRONT PANEL (Q).
Page 6
11F
Do not tighten the TWIST-LOCK® FASTENERS in this step.
D
Q
11F
11F
11F

Step 2
å Fasten the SHELF (D) to the FRONT PANEL (Q). Tighten
three TWIST-LOCK® FASTENERS.
Page 7
D
Q
Surface without
TWIST-LOCK®
FASTENERS
The hole is closer
to this edge.

å Fasten the UPRIGHT (O) to the SHELF (D). Use three
BLACK 1-15/16" FLAT HEAD SCREWS (113S).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
å Turn one CAM SCREW (8F) into the FRONT PANEL (Q).
å Insert one METAL PIN (1R) into the FRONT PANEL (Q).
Step 3
Page 8
8F
1R
D
Q
BLACK 1-15/16" FLAT HEAD SCREW
(3 used in this step)
113S
O

å Push two HIDDEN CAMS (1F) into the BRACE (P).
å Fasten the BRACE (P) to the FRONT PANEL (Q). Tighten
one HIDDEN CAM.
å NOTE: Be sure the METAL PIN in the FRONT PANEL
inserts into the BRACE.
Step 4
Page 9
1F
Arrow
1F Arrow
Q
P
P
Curved edge
Surface with
HIDDEN CAMS

å Push two SAUDER TWIST-LOCK® FASTENERS (11F) into the large holes in the BACK PANEL (R).
å Turn one CAM SCREW (8F) into the BACK PANEL (R).
å Insert one METAL PIN (1R) into the BRACE (P).
å Fasten the BACK PANEL (R) to the SHELF (D). Tighten
three TWIST-LOCK® FASTENERS.
å Fasten the BACK PANEL (R) to the BRACE (P).
Tighten one HIDDEN CAM.
å NOTE: Be sure the METAL PIN in the
BRACE inserts into the BACK PANEL.
Step 5
Page 10
8F
1R
R
11F
11F
PD
R
F
L
I
P
O
V
E
R
The TWIST-LOCK®
is closer to this edge.
1
2