Teknik 5424944 User manual

www.teknikoffice.co.uk
Industrial Style High Stool (set of 2)
Model 5424944
Keep your options
open.
Teknik

Table of Contents Assembly Tools Required
2
3
4-6
9-10
11
Hardware Identification
Part Identification
Assembly Steps
Safety
Warranty
Skip the power trip.
This time.
Page 2
Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
BLACK 3/8" HEX HEAD SCREW - 24
2
L-WRENCH - 1
3
BLACK 1-3/16" HEX HEAD SCREW - 8
1

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A END (4)
B UPPER BRACE (4)
C LOWER BRACE (4)
D SEAT (2)
Page 3
A
B
C
D
A
B
CA
B
C
D
A
B
C

Step 1
å Assemble your unit on a carpeted floor or on the empty carton to
avoid scratching your unit or the floor.
å Fasten two UPPER BRACES (B) to the one of the ENDS (A). Tighten
two BLACK 3/8" HEX HEAD SCREWS (2) using the L-WRENCH (3).
å Fasten two LOWER BRACES (C) to the END (A). Tighten four
BLACK 3/8" HEX HEAD SCREWS (2) using the L-WRENCH (3).
å Repeat this step for the other stool.
Page 4
3
B
C
A
B
C
BLACK 3/8" HEX HEAD SCREW
(12 used in this step)
2
Surface without holes
Surface with four holes
Surface with two holes
Do not use this hole.

å Fasten one of the ENDS (A) to the BRACES (B and C).
Tighten six BLACK 3/8" HEX HEAD SCREWS (2) using
the L-WRENCH (3).
å Fasten the UPPER BRACES (B) to one of the SEATS (D).
Tighten four BLACK 1-3/16" HEX HEAD SCREWS (1)
using the L-WRENCH (3).
å Repeat this step for the other stool.
Step 2
Page 5
BLACK 1-3/16" HEX HEAD SCREW
(8 used for the SEATS)
1
3
BLACK 3/8" HEX HEAD SCREW
(12 used in this step)
2
D
B
C
A
B
C
B
B

å Carefully stand the stools upright.
å NOTE: Please read the back pages of the instruction booklet for important safety information.
å This completes assembly. Clean with a damp cloth. Wipe dry.
Step 3
Page 6

WARNING
Please use your furniture correctly and safely. Improper use can cause safety hazards,
or damage to your furniture or household items. Carefully read the following chart.
Look out for: What can happen: How to avoid the problem:
• A chair or stool will be unstable if you
stand on the seat.
• Leaning back in the chair or stool.
• The chair or stool will come out from
under you, causing a risk of a fall and
severe injury.
• Leaning can cause the chair or stool to
slip out from under you, cause structural
damage, or can loosen important
connections that can cause the chair or
stool to fall apart.
• Never stand on the seat of a chair or stool.
• Don't lean so far back in your chair or
stool that the legs lift up o the floor.
• Loosening of parts or components. –
“Wear and Tear.” • The normal use of a chair or stool can result in loosening of components. The
chair or stool may break or collapse with a
person sitting in it.
• At least twice a year, inspect the chair or
stool to make sure all parts or components
are tightened. Look for loose fasteners and
evidence of cracks or breakage. Tighten,
repair or replace as necessary.