Teknik Credenza 5421317 User manual

www.teknikoffice.co.uk
Get all organized
and stu.
Credenza
Clifton Place Collection | Model 5421317
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Teknik

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
3
3-4
5-28
29-32
33-36
37-38
39
Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or
death. A TV that is too large for the available space might be accidentally pushed or bumped o the furniture, or subject to tip-over.
• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!
• This unit is designed for use with televisions weighing less than 50 pounds. Never use with a TV that weighs more.
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diagram.
• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)
• Never allow the sides of the TV to extend past the side edges of the TV support surface.
• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.
• Be sure to apply the warning label as instructed in the last assembly step. The label provides important safety related information.
WARNING
!
50 lbs.
50 lbs.
18-1/2"
18-1/2"
44"
44"
Page 2

åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
Part Identification
A RIGHT END (1)
B LEFT END (1)
C UPRIGHT (1)
D TOP (1)
E UPPER BACK (1)
F BACK (1)
G SHELF (1)
H ADJUSTABLE SHELF (1)
I LARGE BOTTOM (1)
J SMALL BOTTOM (1)
L SHORT BOTTOM MOLDING (2)
K LONG BOTTOM MOLDING (2)
M LONG TOP MOLDING (1)
N SHORT TOP MOLDING (1)
O LOWER BACK (1)
P LEFT DRAWER SIDE (1)
Q DRAWER BACK (1)
R RIGHT DRAWER SIDE (1)
S DRAWER BOTTOM (1)
T DRAWER BRACE (2)
U DRAWER FRONT (1)
V DOOR (1)
W FOOT (6)
A
B
C
D
E F
G
H
IJ
K
K
L
L
MN
O
P
QR
S
T
T
U
V
WW
W
W
W
W
ANGLED HEAD
CAM SCREW - 30
2
Angled head
LARGE HIDDEN
CAM - 30
1
(EXTENSION SET SHOWN SEPARATED)
XEXTENSION RAIL - 2 YEXTENSION SLIDE - 2
Hardware Identification
Page 3

åScrews are shown actual size. You may receive extra hardware with your unit.
Hardware Identification
WOOD
DOWEL - 34
6SHORT WOOD
DOWEL - 12
7
LONG WOOD
DOWEL - 4
5
METAL PIN - 4
15 RUBBER
SLEEVE - 4
16
APPLIQUE CARD - 1
13
BLACK 1-1/2" FLAT HEAD SCREW - 14
21
SILVER 1/2" FLAT HEAD SCREW - 8
24
BLACK 1/2" PAN HEAD SCREW - 18
23
SMALL HIDDEN
CAM - 8
3STRAIGHT HEAD
CAM SCREW - 8
4
Straight head
LARGE
APPLIQUE CARD - 1
14
ADJUSTABLE
GLIDE -6
10 HINGE BRACKET - 2
11 HINGE - 2 12
GROMMET - 2
9
PULL - 2
8
BLACK 1-1/8" FLAT HEAD SCREW - 12
22
17 SHORT FILE GLIDE - 2
18 LONG FILE
GLIDE - 1 19 NOTCHED FILE GLIDE - 1 20 FILE HANGER - 2
(Refer to the last step for proper
location and application)
WARNING LABEL - 1
25
522,68 22,68
50 lbs. 22 kg 22 kg
Page 4

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push thirty HIDDEN CAMS (1) into the ENDS (A and B),
UPRIGHT (C), SHELF (G), BACKS (E, F, and O ), and
BOTTOMS (I and J).
F
C
A
B
E
O
J
I
G
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
Arrow
Arrow
(30 used)
Arrow
Arrow
1
Hole
1
1
Page 5

å Turn thirty ANGLED HEAD CAM SCREWS (2) into the
ENDS (A and B), UPRIGHT (C), and TOP (D).
å NOTE: The UPRIGHT (C) will have four ANGLED HEAD
SCREWS on one surface and six on the opposite surface.
Step 2
A
B
C
C
F
L
I
P
O
V
E
R
D
Angled head
2
2
(30 used)
Remember:
Righty tighty.
Lefty loosey.
Page 6

å Separate the EXTENSION SLIDES (Y) from the
EXTENSION RAILS (X) as shown in the enlarged diagram
below. Be prepared, the parts are greasy.
å Fasten the EXTENSION RAILS (X) to the LEFT END (B) and
UPRIGHT (C). Use six BLACK 1/2" PAN HEAD SCREWS (23).
å NOTE: For each EXTENSION RAIL, turn a SCREW into
the hole shown in the enlarged diagram. Then, slide the
inner cartridge of the EXTENSION RAIL in to find the
other holes that lines up with the holes in the ENDS. Turn
a SCREW into those holes.
å NOTE: The EXTENSION SLIDES (Y) will be used later for
the DRAWERS.
Step 3
B
C
Pull down on the black release lever and pull the SLIDE from the RAIL.
X
X
X
XY
Y
Use these holes. Open end
Open end
BLACK 1/2" PAN HEAD SCREW
(6 used in this step)
23
Page 7

Step 4
F
L
I
P
O
V
E
R
F
L
I
P
O
V
E
R
I
I
J
J
å Peel an applique from the LARGE APPLIQUE CARD (14)
and stick one on each large hole in the BOTTOMS (I and J).
å Flip the BOTTOMS (I and J) over.
å Turn and tighten six FEET (W) into the threaded holes in
the BOTTOMS (I and J).
å Turn four ADJUSTABLE GLIDES (10) into the threaded
holes in the FEET (W).
14
14
W
W
W
W
W
W
10
10
Page 8
Surface without
HIDDEN CAMS
Surface without
HIDDEN CAMS

Step 5
å Insert eight SHORT WOODEN DOWELS (7) into the
BOTTOMS (I and J).
å Fasten the LONG BOTTOM MOLDINGS (K) to the
LARGE BOTTOM (I). Use four BLACK 1-1/8" FLAT HEAD
SCREWS (22).
å Fasten the SHORT BOTTOM MOLDINGS (L) to the
SMALL BOTTOM (J). Use four BLACK 1-1/8" FLAT HEAD
SCREWS (22).
å NOTE: Be sure the SHORT WOODEN DOWELS insert
into the holes in the BOTTOM MOLDINGS.
7
J
I
BLACK 1-1/8" FLAT HEAD SCREW
(8 used in this step)
22
BLACK 1-1/8" FLAT HEAD SCREW
22
7
K
K
L
L
Page 9
Curved edge

å Insert two WOOD DOWELS (6) into the edge of the
SHELF (G).
å Fasten the SHELF (G) to the UPPER BACK (E). Use two
BLACK 1-1/2" FLAT HEAD SCREWS (21).
å NOTE: Be sure the WOOD DOWELS in the SHELF insert
into the holes in the UPPER BACK.
Step 6
G
E
BLACK 1-1/2" FLAT HEAD SCREW
(2 used in this step)
21
Surface with
HIDDEN CAMS
6
Surface without
HIDDEN CAMS
Page 10