Teknik Market 5425768 User manual

Market Lift Up Coffee Table
Model 5425768
It's addicting.
Teknik
www.teknikoffice.co.uk

Part Identification
Hardware Identification
Assembly Steps
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
Skip the power trip.
This time.
3
4
5-15
Page 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A PANEL (2)
B SHELF (1)
C LEFT END (1)
D RIGHT END (1)
E BOTTOM (1)
F TOP (1)
Page 3
A
B
C
D
E
F
A

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 4
HIDDEN CAM - 6
1
BLACK 1-3/16" HEX HEAD SCREW - 4
11
L-WRENCH - 1
8
CAM SCREW - 6
2WOOD DOWEL - 8 3
BUSHING - 2
5WASHER - 2 6
STRETCHER - 1
7
4BUMPER CARD - 1
BLACK 1-7/8" HEX HEAD SCREW - 8
10
9LIFT TABLE
MECHANISM SET - 1
BLACK 3/8" PAN HEAD SCREW - 2
14
BLACK 11/16" PAN HEAD SCREW - 2
12 BLACK 9/16" PAN HEAD SCREW - 22 13

Hardware Usage Guide
HOW TO USE A HIDDEN CAM & CAM SCREW OR CAM DOWEL
NOTE: Various CAM SCREWS or a CAM DOWEL may be used.
Cam Screws Cam Dowel
Turn the CAM SCREW or
gently tap the CAM DOWEL
until the shoulder is against
the surface of the part.
1.
Hidden CamHidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2.
3.
1
2
Insert the CAM SCREW or CAM DOWEL into the
HIDDEN CAM. Tighten the HIDDEN CAM.
Page 5

Step 1
å Assemble your unit on a carpeted floor or on the empty carton to
avoid scratching your unit or the floor.
å Turn six CAM SCREWS (2) into the PANELS (A).
å Push six HIDDEN CAMS (1) into the SHELF (B).
å Insert eight WOOD DOWELS (3) into the edges of the SHELF (B).
Page 6
2
Arrow
1
Arrow
1
3
A
B
A
(8 used)

Step 2
å Fasten the SHELF (B) to one of the PANELS (A). Tighten
three HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the SHELF insert
into the PANEL.
å Fasten the other PANEL (A) to the SHELF (B). Tighten
three HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the SHELF insert
into the PANEL.
Page 7
A
B
A
These surfaces
should be even.
Surface with
HIDDEN CAMS
Some assembly
(and snacks) required.

å Fasten the RIGHT END (D) to the PANELS (A) and SHELF (B).
Tighten four BLACK 1-7/8" HEX HEAD SCREWS (10) using
the L-WRENCH (8).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
å NOTE: Be sure the WOOD DOWELS in the SHELF insert into
the RIGHT END.
Step 3
Page 8
A
B
8
A
D
The holes in the board
are closer to this edge.
BLACK 1-7/8" HEX HEAD SCREW
(4 used in this step)
10

å Fasten the BOTTOM (E) to the RIGHT END (D).
Tighten two BLACK 1-3/16" HEX HEAD SCREWS (11)
using the L-WRENCH (8).
å NOTE: You should start each SCREW a few turns
before completely tightening any of them.
Step 4
Page 9
E
8
D
BLACK 1-3/16" HEX HEAD SCREW
(2 used in this step)
11
The metal grate is
further from this edge.

å Fasten the LEFT END (C) to the PANELS (A) and SHELF (B).
Tighten four BLACK 1-7/8" HEX HEAD SCREWS (10) using
the L-WRENCH (8).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
å NOTE: Be sure the WOOD DOWELS in the SHELF insert
into the LEFT END.
å Fasten the LEFT END (C) to the BOTTOM (E). Tighten two
BLACK 1-3/16" HEX HEAD SCREWS (11) using
the L-WRENCH (8).
Step 5
Page 10
C
B
E
A
A
8
BLACK 1-7/8" HEX HEAD SCREW
(4 used for the SHELF and PANELS)
10
BLACK 1-3/16" HEX HEAD SCREW
(2 used for the BOTTOM)
11
Now might be a
good time to refresh
your drink.