Teknik 5418072 User manual

www.teknikoffice.co.uk
For all your
newfangled gadgetry.
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Shaker Style Desk
5418072
Teknik

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
2-3
4
5-22
Part Identification
A RIGHT END (1)
B LEFT END (1)
C RIGHT UPRIGHT (1)
D LEFT UPRIGHT (1)
D48 DRAWER RIGHT SIDE (2)
D49 DRAWER LEFT SIDE (2)
D151 DRAWER BACK (2)
D953 DRAWER BOTTOM (2)
E TOP (1)
F BOTTOM (2)
G OUTER BOTTOM (4)
H LARGE BACK (1)
I SMALL BACK (2)
J BRACE (1)
K RIGHT FRONT LEG (2)
L LEFT FRONT LEG (2)
M RIGHT REAR LEG (1)
N LEFT REAR LEG (1)
O RIGHT MIDDLE REAR LEG (1)
P LEFT MIDDLE REAR LEG (1)
Q DRAWER FRONT (2)
R TOP MOLDING (1)
S BOTTOM MOLDING (4)
T BOTTOM SIDE MOLDING (4)
U END MOLDING (2)
Page 2

åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
Part Identification
A
B
C
D
E
F
F
G
G
G
G
H
I
I
J
K
K
L
L
M
N
O
P
Q
Q
R
S
S
S
S
T
T
T
T
U
U
D48D151
D953
D953
D151
D49
D49
D48
Page 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
SILVER 1/2" MACHINE SCREW - 2
38S
METAL BRACKET - 3
4G
BLACK 9/16" LARGE HEAD SCREW - 14
1S
12F TWIST-LOCK®FASTENER - 2
BLACK 2" PAN HEAD SCREW - 4
66S
CAM COVER - 4
19P
3S GOLD 5/16" FLAT HEAD SCREW - 16
BLACK 9/16" FLAT HEAD SCREW - 4
32S
CAM SCREW - 44
8F
WOOD DOWEL - 4
15F
30S BLACK 1-9/16" FLAT HEAD SCREW - 8
HIDDEN CAM - 72
1F CAM DOWEL - 28 2F
100K KNOB SET - 2
FILE DRAWER FRONT
BRACKET - 4
10G
FILE GLIDE - 2
4B
WEXTENSION SLIDE - 4 VEXTENSION RAIL - 4
(EXTENSION SET SHOWN SEPARATED)
Page 4
FILE ROD - 2
7B

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push a WIST-LOCK®
FASTENER (12F) into the large holes in the LARGE BACK (H).
Page 5
Do not tighten the TWIST-LOCK® FASTENERS in this step.
12F
H
(2 used)

å Push seventy-two HIDDEN CAMS (1F) into
the ENDS (A and B), UPRIGHTS (C
and D), BOTTOMS (F and G), BACKS (H
and I), and MOLDINGS (S and T). Then,
insert the metal end of a CAM
DOWEL (2F) into each HIDDEN CAM,
except in the short edges of the ENDS (A
and B), short edges of the UPRIGHTS (C
and D), BACKS (H and I) and
MOLDINGS (S and T).
Step 2
Page 6
I
I
F
F
G
G
G
G
A
B
C
D
T
T
T
T
S
S
S
S
H
Arrow
Arrow
1F
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
Arrow
1F
2F
Arrow
1F
2F
1F
Arrow
(72 used)
(28 used)
Arrow
1F
2F
Do not tighten the
HIDDEN CAMS in
this step.
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow

Step 3
Page 7
å Turn forty-four CAM SCREWS (8F) into the LEGS (K, L, M,
N, O, and P).
K
K
L
L
M
N
O
P
8F
8F
8F
(44 used)

å Turn four BLACK 9/16" FLAT HEAD SCREWS (32S) into
the ENDS (A and B) until the shoulders of the SCREWS
rest on the surfaces of the ENDS.
å Slide the END MOLDINGS (U) onto the ENDS (A and B).
Line up the grooves in the MOLDINGS over the heads of
the SCREWS in the ENDS.
Step 4
Page 8
These edges
should be even.
These edges
should be even.
Shoulder
Shoulder
Apply pressure with your hands
as you guide the MOLDINGS over
the SCREWS and onto the ENDS.
Apply pressure with your hands
as you guide the MOLDINGS over
the SCREWS and onto the ENDS.
BLACK 9/16" FLAT HEAD SCREW
(4 used in this step)
32S
A
B
U
U
Groove
Some assembly
(and snacks) required.

å Flip the ENDS (A and B) over.
å Fasten the LEGS (K and M) and a BOTTOM SIDE
MOLDING (T) to the RIGHT END (A). Tighten six
HIDDEN CAMS.
å Fasten the LEGS (L and N) and a BOTTOM SIDE
MOLDING (T) to the LEFT END (B). Tighten six
HIDDEN CAMS.
Step 5
Page 9
A
B
T
T
K
M
L
N
Surface with HIDDEN CAMS
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
These edges must be even.
These edges must be even.
1
2
LEFT END ASSEMBLY
RIGHT END ASSEMBLY

å Fasten the LEGS (L and O) and a BOTTOM SIDE
MOLDING (T) to the UPRIGHT (C). Tighten six
HIDDEN CAMS.
å Fasten the LEGS (K and P) and a BOTTOM SIDE
MOLDING (T) to the LEFT UPRIGHT (D). Tighten six
HIDDEN CAMS.
Step 6
Page 10
L
O
T
T
Surface with HIDDEN CAMS
C
D
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
K
P
1
2