Teknik Avon 5422051 User manual

Credenza
Avon Collection | Model 5422051
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Your center of
attention.
Teknik
www.teknikoffice.co.uk

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Safety
No. 2 Phillips Screwdriver
Tip Shown Actual Size
WARNING
!
Skip the power trip.
This time.
3
4
5-28
29
Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or
death. A TV that is too large for the available space might be accidentally pushed or bumped o the furniture, or subject to tip-over.
• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!
• This Sauder unit is designed for use with televisions weighing less than 70 pounds. Never use with a TV that weighs more.
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diagram.
• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)
• Never allow the sides of the TV to extend past the side edges of the TV support surface.
• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.
• Be sure to apply the warning label as instructed in the last assembly step. The label provides important safety related information.
70 lbs.
70 lbs.
17-1/2"
17-1/2"
60-1/8"
60-1/8"
Page 2
Short Screwdriver

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C UPRIGHT (1)
D TOP (1)
E SHELF (1)
F BOTTOM (1)
G UPPER DIVIDER (1)
H LOWER DIVIDER (1)
J ADJUSTABLE SHELF (1)
K BACK (1)
L DOOR (1)
M RIGHT DRAWER FRONT (1)
N LEFT DRAWER FRONT (1)
O RIGHT DRAWER SIDE (2)
P LEFT DRAWER SIDE (2)
Q DRAWER BACK (2)
R DRAWER BOTTOM (2)
S LEG (2)
T STRETCHER (3)
Page 3
A
B
C
D
E
G
H
J
T
K
S
L
M
F
N
O
P
Q
R
O
Q
R
S
T
T
P

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 4
HIDDEN CAM - 9
3ANGLED HEAD
CAM SCREW - 9
4
Angled head
(EXTENSION SET SHOWN SEPARATED)
1EXTENSION RAIL - 4 2EXTENSION SLIDE - 4
WOOD DOWEL - 9
7
SMALL HIDDEN
CAM - 8
5STRAIGHT HEAD
CAM SCREW - 8
6
Straight head
PLASTIC BRACKET - 8
8
HINGE - 2
9CLIP - 12
11 PULL - 3
12 METAL PIN - 4
13
(Refer to the last step for proper location and application)
WARNING LABEL - 1
15
522,68 22,68
70 lbs. 31,75 kg 31,75 kg
APPLIQUE CARD - 3
14 BLACK 1-1/2" FLAT HEAD SCREW - 13 16
BLACK 1/2" MACHINE SCREW - 36
18
BLACK 1/2" WAFER HEAD SCREW - 12
19
SILVER 1/2" FLAT HEAD SCREW - 4
22
BLACK 1/2" PAN HEAD SCREW - 6
20
SMALL BLACK 1/2" PAN HEAD SCREW - 24
21
SILVER 5/8" FLAT HEAD SCREW - 12
17
HINGE BRACKET - 2
10

Step 1
Page 5
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push nine HIDDEN CAMS (3) into the UPRIGHT (C),
SHELF (E), and DIVIDERS (G and H).
C
G
Arrow
3
Arrow
3 (9 used)
Some assembly
(and snacks) required.
H
E
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
Arrow
3

Step 2
Page 6
å Turn nine ANGLED HEAD CAM SCREWS (4) into the exact
holes shown in the RIGHT END (A), UPRIGHT (C), TOP (D),
and SHELF (E).
4
(9 used)
Angled head
C
E
A
D
Surface with
HIDDEN CAMS

Step 3
Page 7
å Fasten the PLASTIC BRACKETS (8) to the TOP (D) and
BOTTOM (F). Use eight BLACK 1/2" MACHINE SCREWS (18).
å NOTE: Be sure to position the BRACKETS exactly
as shown.
BLACK 1/2" MACHINE SCREW
(8 used in this step)
18
D
F
8
8

å Fasten the HINGE BRACKETS (10) to the LEFT END (B).
Use the screws in the HINGE BRACKETS.
å NOTE: Be sure to position the HINGE BRACKETS exactly
as shown.
Step 4
Page 8
10
B
Groove

Step 5
Page 9
å Separate the EXTENSION SLIDES (2) from the EXTENSION RAILS (1) as shown in the upper diagram below. Be
prepared, the parts are greasy.
å Fasten two EXTENSION RAILS (1) to the RIGHT END (A) and UPRIGHT (C). Use six SMALL BLACK 1/2" PAN
HEAD SCREWS (21).
å NOTE: Use the exact holes shown.
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram. Then, slide the inner
cartridge of the EXTENSION RAIL out to find the other holes that line up with the holes in the END and UPRIGHT. Turn
a SCREW into these holes.
12
Pull down on the black lever and pull the SLIDE from the RAIL.
C
A
1
1
SMALL BLACK 1/2" PAN HEAD SCREW
(6 used in this step)
21
Surface with
CAM SCREWS
Surface with
CAM SCREWS
Groove
Use this hole
Open end

Step 6
Page 10
å Fasten two EXTENSION RAILS (1) to both surfaces of the LOWER DIVIDER (H). Use six SMALL BLACK 1/2" PAN
HEAD SCREWS (21).
å NOTE: Use the exact holes shown.
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram. Then, slide the inner
cartridge of the EXTENSION RAIL out to find the other holes that line up with the holes in the LOWER DIVIDER. Turn a
SCREW into these holes.
SMALL BLACK 1/2" PAN HEAD SCREW
(6 used in this step)
21
Use the small
round hole
Use the slotted hole
Open end
Open end
Surface with
HIDDEN CAMS
H
Surface without
HIDDEN CAMS
H
F
L
I
P
O
V
E
R
F
L
I
P
O
V
E
R
Finished edge
Finished edge
1
1