Teknik Barrister Home User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Barrister Home Sideboard
Barrister Home Collection | Model 5416488
Your centre
of attention.
Teknik
www.teknikoffice.co.uk

Table of Contents Assembly Tools Required
3
4-5
6-20
21-24
25-28
29-30
31
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or
death. A TV that is too large for the available space might be accidentally pushed or bumped o the furniture, or subject to tip-over.
• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!
• This Sauder unit is designed for use with televisions weighing less than 95 pounds. Never use with a TV that weighs more.
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diagram.
• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)
• Never allow the sides of the TV to extend past the side edges of the TV support surface.
• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.
• Be sure to apply the warning label as instructed in the last assembly step. The label provides important safety related information.
WARNING
!
19-1/4"
19-1/4"
Skip the power trip.
This time.
Page 2
57"
57"
95 lbs.
95 lbs.

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C RIGHT UPRIGHT (1)
D LEFT UPRIGHT (1)
E2 TOP (1)
F BOTTOM (1)
G BACK (1)
H DOOR (1)
I DOOR (1)
J LARGE ADJUSTABLE SHELF (1)
K SMALL ADJUSTABLE SHELF (2)
L BASE (1)
M TOP MOLDING (1)
N LARGE SHELF MOLDING (1)
O SMALL SHELF MOLDING (2)
P END MOLDING (4)
Q CATCH BRACE (1)
R STOP MOLDING (1)
Now you know
our ABCs.
Page 3
A
B
C
D
E2
F
G
I
H
J
K
L
M
N
O
P
Q
O
K
P
P
P
R

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
(Refer to the last step for proper
location and application)
WARNING LABEL - 1
3L
WARNING
Never use this furniture with a TV that is too
large or too heavy. Severe injury or death
can occur.The TV and furniture will be
unstable and may tip.
-The TV must less than 95 lbs.
-The base of the TV must be able to sit
completely on this shelf.
-Refer to instruction book for complete
safety information.
Note: This is a permanent label. Do not try
to remove. Surface will be damaged.
02/ 02 269227
31G CORNER
BRACKET - 2
METAL BRACKET - 9
4G
CAM COVER - 12
13P RUBBER SLEEVE - 12 2R
METAL PIN - 12
1R
SMALL MAGNETIC
CATCH - 1
2I STRIKE PLATE - 2 6I
NAIL - 48
1N
HIDDEN CAM - 30
1F CAM DOWEL - 30 2F
KNOB - 1
69K
FOOT - 2
23E
MAGNETIC CATCH - 1
12I
27H HINGE - 4
39M DECORATIVE
POST - 2
Page 4
33M DECORATIVE
END - 2
34M DECORATIVE
BACKPLATE - 1

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 5
BLACK 9/16" PAN HEAD SCREW - 2
51S
SILVER 3/4" MACHINE SCREW - 2
20S
BLACK 9/16" LARGE HEAD SCREW - 46
1S BLACK 1-7/8" FLAT HEAD SCREW - 4 2S
BLACK 1/2" FLAT HEAD SCREW - 2
11S
SILVER 1-1/2" MACHINE SCREW - 1
95S

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push thirty HIDDEN CAMS (1F) into the ENDS (A
and B), UPRIGHTS (C and D), TOP (E2), BOTTOM (F),
and CATCH BRACE (Q). Then, insert the metal end of a
CAM DOWEL (2F) into each HIDDEN CAM.
Page 6
Arrow
1F
2F
Arrow
1F
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not tighten the HIDDEN CAMS in this step.
(30 used)
A
B
C
D
F
Q
E2

StepStep 2
å Fasten the END MOLDINGS (P) to the ENDS (A and B)
and UPRIGHTS (C and D). Tighten twelve HIDDEN CAMS.
Page 7
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS Surface with
HIDDEN CAMS
A
B
C
D
P
P
P
P
These holes should
be located here.
These holes should
be located here.

Step 3
å Fasten the METAL BRACKETS (4G) to the UPRIGHTS (C and D),
BOTTOM (F), and TOP MOLDING (M). Use nine BLACK 9/16"
LARGE HEAD SCREWS (1S).
å NOTE: The METAL BRACKETS should hang over the edges
slightly on the UPRIGHTS.
å NOTE: The METAL BRACKETS should be even with the edges
on the BOTTOM and TOP MOLDING.
å Fasten the CORNER BRACKETS (31G) to the BOTTOM (F). Use
four BLACK 9/16" LARGE HEAD SCREWS (1S).
Page 8
Remember:
Righty tighty.
Lefty loosey.
C
D
F
Surface without
HIDDEN CAMS
Surface with
HIDDEN CAMS
Surface without
HIDDEN CAMS
4G
4G
4G
4G
31G
31G
MFlat surface
BLACK 9/16" LARGE HEAD SCREW
(13 used in this step)
1S

StepStep 4
å Fasten the LEFT END (B) and STOP MOLDING (R) to the
TOP (E2). Tighten six HIDDEN CAMS.
Page 9
Surface with
HIDDEN CAMS
P
E2
B
Arrow
Minimum
190 degrees
Maximum
210 degrees
Finished surface
Surface with
HIDDEN CAMS
R
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution

Step
å Fasten the UPRIGHTS (C and D) to the TOP (E2). Tighten
four HIDDEN CAMS.
Step 5
Page 10
C
D
Surface with
HIDDEN CAMS
P
P
Surface without
HIDDEN CAMS
E2
Arrow
Minimum
190 degrees
Maximum
210 degrees