Teknik Lux Desk 5426429 User manual

Lux Desk
Model 5426429
Sit and surf.
Teknik
www.teknikoffice.co.uk

Part Identification
Hardware Identification
Assembly Steps
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
3
4
5-26
Pae 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A LEFT FRAME (1)
B CENTER FRAME (1)
C RIGHT FRAME (1)
D TOP (1)
E LEFT END (1)
F UPRIGHT (1)
G RIGHT END (1)
H SHELF (2)
J BOTTOM (1)
K RIGHT BACK (1)
L LEFT BACK (1)
M EXTENSION BLOCK (1)
N DRAWER FRONT (1)
O LEFT DRAWER SIDE (1)
P RIGHT DRAWER SIDE (1)
Q DRAWER BACK (1)
R DRAWER BOTTOM (1)
S DRAWER BRACE (1)
T FILE DRAWER FRONT (1)
U FILE LEFT DRAWER SIDE (1)
V FILE RIGHT DRAWER SIDE (1)
W FILE DRAWER BACK (1)
X FILE DRAWER BOTTOM (1)
Y LONG BRACE (1)
Z SHORT BRACE (2)
A
B
C
D
E
F
G
H
J
K
LM
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Z
H
Pae 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
HIDDEN CAM - 12
21-3/16" HEX HEAD SCREW - 6
3
CAM SCREW - 12
1
1/2" HEX HEAD SCREW - 2
6
1-3/8" HEX HEAD SCREW - 6
4METAL PIN - 6
5
7/16" PAN HEAD SCREW - 24
8GOLD 1/2" FLAT HEAD SCREW - 18 9
1-3/16" FLAT HEAD SCREW - 14
7
METAL BRACKET - 8
11 PULL - 2
12
3/4" FLAT HEAD SCREW - 2
10
16 RIGHT EXTENSION
RAIL and SLIDE - 1
15 LEFT EXTENSION
RAIL and SLIDE - 1
14 RIGHT FILE GLIDE - 1 13 LEFT FILE GLIDE - 1
L-WRENCH - 1
19 APPLIQUE CARD - 2 20
18 WIDE EXTENSION
SLIDE - 2
17 WIDE EXTENSION
RAIL - 2
Pae 4

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Turn twelve CAM SCREWS (1) into the TOP (D), DRAWER
FRONT (N), and FILE DRAWER FRONT (T).
Pae 5
1(12 used)
D
N
T

å Push twelve HIDDEN CAMS (2) into the LEFT BACK (L),
DRAWER SIDES (O and P), DRAWER BRACE (S), and FILE
DRAWER SIDES (U and V).
Step 2
Pae 6
L
P
O
S
U
V
Arrow
2
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the ede of the board.
Hole
(12 used)

å NOTE: Position the parts exactly as shown.
å Fasten the RIGHT EXTENSION RAIL and SLIDE (16) to the EXTENSION BLOCK (M) and UPRIGHT (F). Use two
3/4" FLAT HEAD SCREWS (10) throuh the RIGHT EXTENSION RAIL and SLIDE, throuh the EXTENSION BLOCK,
and into the UPRIGHT.
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlared diaram. Then, slide the inner
cartride of the EXTENSION RAIL in to find the other hole that lines up with the hole in the UPRIGHT. Turn a SCREW
into this hole.
Step 3
Pae 7
F
Finished ede
Surface with fewer holes
3/4" FLAT HEAD SCREW
(2 used in this step)
16
M
Closed end
Finished surface
6th hole
16
M
Bracket must
be positioned
as shown
16
Use these holes
16
10

Step 4
Pae 8
E
å NOTE: Position the parts exactly as shown.
å Fasten the LEFT EXTENSION RAIL and SLIDE (15) to the LEFT
END (E). Use two GOLD 1/2" FLAT HEAD SCREWS (9).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole
shown in the enlared diaram. Then, slide the inner cartride
of the EXTENSION RAIL in to find the other hole that lines up
with the hole in the END. Turn a SCREW into this hole.
GOLD 1/2" FLAT HEAD SCREW
(2 used in this step)
9
Closed end
6th hole
Finished ede
15
Bracket must
be positioned
as shown
15
E
15
Some assembly
(and snacks) required.
Use these holes
15

å Flip the UPRIGHT (F) over.
å Separate the WIDE EXTENSION SLIDES (18) from the WIDE EXTENSION RAILS (17) as shown in the upper diaram
below. Be prepared, the parts are reasy.
å Fasten the WIDE EXTENSION RAILS (17) to the UPRIGHT (F) and RIGHT END (G). Use four GOLD 1/2" FLAT
HEAD SCREWS (9).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlared diaram. Then, slide the inner
cartride of the EXTENSION RAIL in to find the other hole that lines up with the hole in the UPRIGHT and RIGHT END.
Turn a SCREW into this hole.
å NOTE: The EXTENSION SLIDES will be used later for the DRAWERS.
Step 5
Pae 9
F G
Finished ede
17 17
Slide the black lever up and pull the SLIDE from the RAIL.
Open end
Open end
GOLD 1/2" FLAT HEAD SCREW
(4 used in this step)
9
Use this hole Use this hole
Use these holes
17 18
17

å Fasten eiht METAL BRACKETS (11) to the UPRIGHT (F)
and RIGHT END (G) exactly as shown. Use eiht 7/16"
PAN HEAD SCREWS (8).
Step 6
Pae 10
F
G
11
11
Finished
ede
Finished
ede
7/16" PAN HEAD SCREW
(8 used in this step)
8