Teknik 5412320 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Home Study L Shaped Desk
Model 5412320
www.teknikoffice.co.uk
Sit and surf.
Teknik

Table of Contents Assembly Tools Required
3
4
5-32
41
Part Identification
Hardware Identification
Assembly Steps
Safety
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
Page 2

Part Identification Now you know
our ABCs.
Page 3
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C LEFT UPRIGHT (1)
D RIGHT TOP (1)
D14 RIGHT DRAWER SIDE (1)
D15 LEFT DRAWER SIDE (1)
D78 DRAWER BACK (1)
D716 DRAWER BOTTOM (1)
E LEFT TOP (1)
F BOTTOM (1)
G RIGHT MODESTY PANEL (1)
H LEFT MODESTY PANEL (1)
I PURSE SHELF (1)
J SHELF (1)
K BACK (1)
L LEFT LEG (1)
M RIGHT FRONT/LEFT REAR LEG (3)
N LEFT CORNER LEG (1)
O RIGHT CORNER LEG (1)
P RIGHT REAR LEG (1)
Q BACK LEG (1)
R DRAWER FRONT (1)
W PURSE SHELF MOLDING (1)
X LEFT FRONT MOLDING (1)
Y RIGHT FRONT MOLDINIG (1)
Z FRONT MOLDING (1)
AA TOP LEFT SIDE MOLDING (1)
BB TOP RIGHT SIDE MOLDING (1)
CC BOTTOM MOLDING (1)
DD LEFT END MOLDING (1)
EE LOWER LEFT MOLDING (1)
FF UPPER LEFT MOLDING (1)
GG LOWER RIGHT MOLDING (1)
HH UPPER RIGHT MOLDING (1)
II RIGHT END MOLDING (1)
A
B
C
D
E
F
G
H
I
J
K
L
M
NO
P
Q
R
W
X
Y
Z
AA
BB
CC
EE
FF
GG
HH
II
DD
M
M
D14
D716
D78
D15

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 4
KK EXTENSION SLIDE - 2
JJ EXTENSION RAIL - 2
(EXTENSION SET SHOWN SEPARATED)
RR GROMMET - 2 GROMMET CAP - 2 SS
TWIST-LOCK®
FASTENER - 18
MM
ANGLE BRACKET - 12
PP
SUPPORT PIN - 2
TT
SLIDE CAM - 2
YY
PULL - 1
WW
CORD CLIP - 2
VV
WASHER - 1
XX
TIE PLATE - 2
QQ
AAA SCREW COVER - 10CAM COVER - 10
ZZ
BBB BLACK 2-1/4" FLAT HEAD SCREW - 2 CCC BLACK 1-7/8" FLAT HEAD SCREW - 9
DDD BLACK 9/16" LARGE HEAD SCREW - 32 EEE BLACK 9/16" FLAT HEAD SCREW - 12
FFF GOLD 5/16" FLAT HEAD SCREW - 8
HHH NAIL - 22
GGG SILVER 1/4" MACHINE SCREW - 1
FILE GLIDE - 2
LL
30S BLACK 1-9/16" FLAT HEAD SCREW - 4
HIDDEN CAM - 18
NN CAM SCREW - 18 OO

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push a TWIST-LOCK®
FASTENER (MM) into the large holes in the BOTTOM (F)
and RIGHT MODESTY PANEL (G). Repeat this step for the
LEFT MODESTY PANEL (H), PURSE SHELF (I), SHELF (J),
and CORNER LEGS (N and O).
Page 5
F
G
MM
MM
MM
(18 used)
Do not tighten the TWIST-LOCK® FASTENERS in this step.

Step 2
å Push eighteen HIDDEN CAMS (NN) into the ENDS (A and B),
LEFT UPRIGHT (C), and LEGS (L, M, P, and Q).
Page 6
A
B
C
L
M
P
Q
M
M
(18 used)
Arrow
NN
Arrow
Arrow Do not tighten the HIDDEN CAMS in this step.
NN
NN
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole

å Turn eighteen CAM SCREWS (OO) into the TOPS (D and E)
and LEGS (L, M, P, and Q).
Step 3
Page 7
D
E
M
M
M
P
Q
L
OO
(18 used)

Step 4
å Fasten the LEGS (L, M, and Q) to the ENDS (A and B) and
LEFT UPRIGHT (C). Tighten eight HIDDEN CAMS.
Page 8
A
B
C
M
M
Q
L
Curved edge
Finished edge
Curved edge
Finished edge
Finished edge
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
These surfaces should be even.
These surfaces should be even.
12

å Carefully turn the ENDS (A and B) over.
å Turn twelve BLACK 9/16" FLAT HEAD SCREWS (EEE) into the
ENDS (A and B) until the shoulders of the SCREWS rest on the
surfaces of the ENDS.
å First, slide the LOWER MOLDINGS (EE and GG) onto the ENDS (A and B).
Line up the grooves in the MOLDINGS over the heads of the SCREWS in
the ENDS.
å Second, slide the END MOLDINGS (DD and II) onto the ENDS (A and B)
until they are against the LOWER MOLDINGS. Line up the grooves in the
MOLDINGS over the heads of the SCREWS in the ENDS.
Step 5
Page 9
B
A
GG
EE
DD
II
2nd
1st
1st
2nd
BLACK 9/16" FLAT HEAD SCREW
(12 used in this step)
EEE
These edges should be even.
These edges should be even.
Shoulder
Apply pressure with your hands as you guide the
MOLDINGS over the SCREWS and onto the ENDS.
Shoulder
Remember:
Righty tighty.
Lefty loosey.

Step 6
å Slide the UPPER MOLDINGS (FF and HH) onto the
ENDS (A and B). Line up the grooves in the MOLDINGS
over the heads of the SCREWS in the ENDS.
Page 10
B
A
FF
HH
These edges should be even.
These edges should be even.
Shoulder
Apply pressure with your hands as you guide the
MOLDINGS over the SCREWS and onto the ENDS.