Teknik Hampstead Park Compact Desk 5420284 User manual

www.teknikoffice.co.uk
The oriinal desktop.
Compact Desk
Hampstead Park Collection | Model 5420284
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Teknik

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Hammer
Not actual size
3
4
5-27
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
Pae 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C UPRIGHT (1)
D TOP (1)
E BACK (1)
F LARGE BOTTOM (1)
G SMALL BOTTOM (1)
H TOP BRACE (1)
I LEFT LEG (1)
J STRETCHER (1)
K RIGHT LEG (1)
L LEFT PENCIL DRAWER SIDE (1)
M PENCIL DRAWER BACK (1)
N RIGHT PENCIL DRAWER SIDE (1)
O PENCIL DRAWER BOTTOM (1)
P PENCIL DRAWER BRACE (1)
Q PENCIL DRAWER FRONT (1)
R LEFT FILE DRAWER SIDE (1)
S FILE DRAWER BACK (1)
T RIGHT FILE DRAWER SIDE (1)
U FILE DRAWER BOTTOM (1)
V FILE DRAWER FRONT (1)
A
B
C
D
E
F
G
H
I
J
K
L
MN
O
P
Q
R
ST
U
V
Pae 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
LARGE HIDDEN
CAM - 27
1ANGLED HEAD
CAM SCREW - 27
3
Anled head
WOOD
DOWEL - 24
5
SMALL HIDDEN
CAM - 10
2STRAIGHT HEAD
CAM SCREW - 10
4
Straiht head
KNOB - 3
6
AA EXTENSION RAIL - 2 BB EXTENSION SLIDE - 2
(EXTENSION SET
SHOWN SEPARATED)
LEFT CABINET
RAIL - 1
DD
RIGHT CABINET RAIL - 1
CC
LEFT DRAWER
SLIDE - 1
FF
RIGHT DRAWER
SLIDE - 1
EE
BLACK 9/16" WAFER HEAD SCREW - 16
14 15 BLACK 12" MACHINE SCREW  4
10 BLACK 2" MACHINE SCREW  2 BLACK 1-1/16" WAFER HEAD SCREW - 4 19
13 BLACK 78" MACHINE SCREW  3
8FILE
GLIDE - 2 9FILE HANGER  2
BLACK 1-1/2" FLAT HEAD SCREW - 10
12
BLACK 1/2" FLAT HEAD SCREW - 12
17
BLACK 1/2" PAN HEAD SCREW - 12
16
CAM COVER
CARD - 1
7
Pae 4
18 ASSEMBLY
TOOL  1

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Push twenty-seven LARGE HIDDEN CAMS (1) into the
ENDS (A and B), UPRIGHT (C), TOP (D), and
BOTTOMS (F and G).
G
C
A
B
F
D
Arrow
Arrow
1
Arrow (27 used)
1
Arrow
1
Arrow
1
The arrow in the HIDDEN
CAM must point toward the
hole in the ede of the board.
Hole
Pae 5

Step 2
F
L
I
P
O
V
E
R
C
C
A
B
E
D
Anled head
3
å Turn twenty-seven ANGLED HEAD CAM SCREWS (3) into
the ENDS (A and B), UPRIGHT (C), TOP (D), and BACK (E).
å NOTE: Be sure to flip over the UPRIGHT (C) to turn two
ANGLE HEAD CAM SCREWS (3) into the opposite surface
as shown in the lower left of this pae.
(27 used)
Pae 6
Remember:
Rihty tihty.
Lefty loosey.

Step 3
C
C
A
B
E
D
å Insert twenty-four WOOD DOWELS (5) into the
ENDS (A and B), UPRIGHT (C), TOP (D), and BACK (E).
å NOTE: Be sure to flip over the UPRIGHT (C) to insert two
more WOOD DOWELS into the opposite surface as shown
in the lower left of this pae.
5
(24 used)
F
L
I
P
O
V
E
R
Pae 7

Step 4
C
A
å Separate the EXTENSION SLIDES (BB) from the EXTENSION RAILS (AA) as shown in the enlared diaram below. Be
prepared, the parts are reasy.
å Fasten the EXTENSION RAILS (AA) to the RIGHT END (A) and UPRIGHT (C). Use six BLACK 1/2" PAN HEAD
SCREWS (16).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlared diaram. Then, slide the inner
cartride of the EXTENSION RAIL out to find the other two holes that line up with the holes in the END. Turn a SCREW
into those holes.
å NOTE: The EXTENSION SLIDES will be used later for the DRAWERS.
Pull up or down on the black lever and pull the SLIDE from the RAIL.
AA
BB
BLACK 1/2" PAN HEAD SCREW
(6 used in this step)
16
Open end
Open end
Rounded corner
Rounded corner
AA
AA
Pae 8 www.sauder.com 420284

Step 5
C
Roller end
Roller end
Rounded corner
Rounded corner
BLACK 1/2" FLAT HEAD SCREW
(6 used in this step)
17
B
å Flip the UPRIGHT (C) over.
å Fasten the CABINET RAILS (CC and DD) to the UPRIGHT (C) and
LEFT END (B). Use six BLACK 1/2" FLAT HEAD SCREWS (17).
CC
DD
Pae 9www.sauder.com420284

å Fasten the TOP BRACE (H) to the TOP (D). Use four
BLACK 1-1/16" WAFER HEAD SCREWS (19).
Step 6
BLACK 1-1/16" WAFER HEAD SCREW
(4 used in this step)
D
H
Surface with
HIDDEN CAMS
Pae 10 www.sauder.com 420284
19