Teknik Clifton Place 5421115 User manual

www.teknikoffice.co.uk
The stories of your life.
Storage Sideboard
Clifton Place Collection | Model 5421115
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Teknik

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
3
4
5-21
22-25
26-28
29-30
31
Page 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D TOP MOLDING (1)
E UPPER BACK (1)
F BRACE (1)
G ADJUSTABLE SHELF (1)
H LOWER BACK (1)
I BOTTOM (1)
J BOTTOM MOLDING (2)
K LEFT DRAWER SIDE (1)
L DRAWER BACK (1)
M RIGHT DRAWER SIDE (1)
N DRAWER BOTTOM (1)
O DRAWER BRACE (1)
P DRAWER FRONT (1)
Q LEFT DOOR (1)
R RIGHT DOOR (1)
S FOOT (4)
A
B
C
D
E
F
G
H
I
J
J
K
LM
N
O
S
S
S
S
P
QR
Page 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
ANGLED HEAD
CAM SCREW - 20
2
Angled head
LARGE HIDDEN
CAM - 20
1
WOOD
DOWEL - 22
6SHORT WOOD
DOWEL - 6
7
LONG WOOD
DOWEL - 4
5
METAL PIN - 4
15 RUBBER
SLEEVE - 4
16
APPLIQUE CARD - 1
13
BLACK 1-1/2" FLAT HEAD SCREW - 8
17
SILVER 1/2" FLAT HEAD SCREW - 14
19 BLACK 1/2" PAN HEAD SCREW - 12 20
SMALL HIDDEN
CAM - 6
3STRAIGHT HEAD
CAM SCREW - 6
4
Straight head
LARGE
APPLIQUE CARD - 1
14
ADJUSTABLE
GLIDE - 4
10 HINGE BRACKET - 4
11 HINGE - 4 12
GROMMET
WITH CAP- 1
9
PULL - 3
8
BLACK 1-1/8" FLAT HEAD SCREW - 9
18
(EXTENSION SET SHOWN SEPARATED)
TEXTENSION RAIL - 2 UEXTENSION SLIDE - 2
Page 4

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å NOTE: If you are attaching the 421116 Hutch to your unit,
build the Hutch first.
å Push twenty LARGE HIDDEN CAMS (1) into the
ENDS (A and B), BRACE (F), LOWER BACK (H),
UPPER BACK (E) and BOTTOM (I).
Arrow (20 used)
Arrow
Arrow
1
1
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
A
B
F
E
I
H
Page 5

Step 2
å Peel an applique from the LARGE APPLIQUE CARD (14)
and stick one on each large hole in the BOTTOM (I).
å Flip the BOTTOM (I) over.
å Turn and tighten four FEET (S) into the threaded holes in
the BOTTOM (I).
å Turn four ADJUSTABLE GLIDES (10) into the threaded
holes in the FEET (S).
I
I
S
S
S
S
10
F
l
i
p
t
h
e
B
O
T
T
O
M
o
v
e
r
Page 6
Surface without
HIDDEN CAMS
14

StepStep 3
å Insert four SHORT WOODEN DOWELS (7) into the
BOTTOM (I).
å Fasten the BOTTOM MOLDINGS (J) to the BOTTOM (I).
Use six BLACK 1-1/8" FLAT HEAD SCREWS (18).
å NOTE: Be sure the SHORT WOODEN DOWELS insert
into the holes in the BOTTOM MOLDINGS.
7
7
J
J
I
BLACK 1-1/8" FLAT HEAD SCREW
(6 used in this step)
18
Page 7

StepStep 4
2(20 used)
Angled head
Remember:
Righty tighty.
Lefty loosey.
å Turn twenty ANGLED HEAD CAM SCREWS (2) into the
ENDS (A and B) and TOP (C).
A
B
C
Page 8

StepStep 5
Push the black lever up and
pull the SLIDE from the RAIL.
T
T
T
U
Use these holes.Open end
BLACK 1/2" PAN HEAD SCREW
(6 used for the RAILS)
20
Open end
Open end
11
11
å Separate the EXTENSION SLIDES (U) from the EXTENSION RAILS (T) as shown in the enlarged diagram below. Be
prepared, the parts are greasy.
å Fasten two EXTENSION RAILS (T) to the ENDS (A and B). Use six BLACK 1/2" PAN HEAD SCREWS (20).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram. Then, slide the inner
cartridge of the EXTENSION RAIL in to find the other holes that line up with the holes in the ENDS. Turn a SCREW into
those holes.
å NOTE: The EXTENSION SLIDES will be used later for the DRAWERS.
å Fasten the HINGE BRACKETS (11) to the ENDS (A and B) exactly as shown. Use the SCREWS in the brackets.
A
B
Page 9

StepStep 6
å Insert four LONG WOOD DOWELS (5) into the LOWER
BACK (H).
å Fasten the UPPER BACK (E) to the LOWER BACK (H) by
pushing it onto the WOOD DOWELS in the LOWER BACK.
5
5
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
E
H
Page 10
Notch