Teknik Boulevard Cafe 5427345 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Lateral File
Boulevard Cafe Collection | Model 5427345
Get all organized
and stu.
Teknik
www.teknikoffice.co.uk

Part Identification
Hardware Identification
Hardware Usage Guide
Assembly Steps
Safety
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
Hammer
Not actual size
3
4-5
6
7-22
23
Pae 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A TOP (1)
B LEFT END (1)
C RIGHT END (1)
D LEFT BACK (1)
E RIGHT BACK (1)
F DRAWER FRONT (2)
G DRAWER BACK (2)
H LEFT DRAWER SIDE (2)
J DRAWER BOTTOM (2)
K DRAWER BRACE (2)
L LOWER FRONT BRACE (1)
M UPPER FRONT BRACE (1)
N LOWER BACK BRACE (1)
P RIGHT DRAWER SIDE (2)
Q UPPER BACK BRACE (1)
Pae 3
A
B
C
D
E
F
G
H
J
K
L
M
N
P
Q
F
G
H
J
K
P

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Pae 4
EXTENSION SET SHOWN SEPARATED
1EXTENSION RAIL - 4 2EXTENSION SLIDE - 4 3FRONT FILE
GLIDE  2
4LONG FILE
GLIDE - 2 5SHORT FILE GLIDE - 4 6FILE HANGER  4
CAM SCREW - 10
8LARGE WOOD
DOWEL - 2
9
SMALL WOOD
DOWEL - 18
10 HOOK - 2 11 PULL - 2 12
L-WRENCH - 2
15
APPLIQUE CARD - 2
13 STRAP - 2 14
HIDDEN CAM - 10
7

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Pae 5
9/16" PAN HEAD SCREW - 18
19
1-3/4" HEX HEAD SCREW - 4
16 1-1/2" FLAT HEAD SCREW - 12 17
1/2" MACHINE SCREW - 4
20
3/8" FLAT HEAD SCREW - 24
22
1-1/2" HEX HEAD SCREW - 8
18
3/8" HEX HEAD SCREW - 4
21
NUT - 4
23

HOW TO USE A HIDDEN CAM & CAM SCREW OR CAM DOWEL
NOTE: Various CAM SCREWS or a CAM DOWEL may be used.
Cam Screws Cam Dowel
Turn the CAM SCREW or
gently tap the CAM DOWEL
until the shoulder is against
the surface of the part.
1.
Hidden CamHidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2.
3.
1
2
Insert the CAM SCREW or CAM DOWEL into the
HIDDEN CAM. Tighten the HIDDEN CAM.
Hardware Usae Guide
Pae 6

Step 1
å Assemble your unit on a carpeted floor or on the empty carton to avoid scratchin your unit or the floor.
å Separate the EXTENSION SLIDES (2) from the EXTENSION RAILS (1) as shown in the upper diaram below. Be
prepared, the parts are reasy.
å Fasten the EXTENSION RAILS (1) to the ENDS (B and C). Use twelve 3/8" FLAT HEAD SCREWS (22) throuh the
exact holes shown.
å NOTE: For each EXTENSION RAIL, turn a SCREW into the 1st hole shown in the enlared diaram. Then, slide the
inner cartride of the EXTENSION RAIL in to find the other two holes that line up with the holes in the END. Turn a
SCREW into each of these holes.
Pae 7
B
C
Slide the black lever, and pull the SLIDE from the RAIL.
12
1st
1st
1st
Open end
Open end
1
1
3/8" FLAT HEAD SCREW
(12 used in this step)
22
1st
1st
1
1

å Fasten the BACK BRACES (N and Q) to the LEFT
END (B). Tihten two 1-1/2" HEX HEAD SCREWS (18)
usin the L-WRENCH (15).
Step 2
Pae 8
15
BN
Q
The EXTENSION RAILS
are closer to this ede.
1-1/2" HEX HEAD SCREW
(2 used in this step)
18
Ede with three tabs
Ede with four tabs
Surface with holes
Some assembly
(and snacks) required.

å Fasten the FRONT BRACES (L and M) to the LEFT
END (B). Tihten two 1-1/2" HEX HEAD SCREWS (18)
usin the L-WRENCH (15).
Step 3
Pae 9
15
1-1/2" HEX HEAD SCREW
(2 used in this step)
18
B
L
MThe tabs face down and
are closer to this surface.

å Fasten the RIGHT END (C) to the BRACES (L, M, N,
and Q). Tihten four 1-1/2" HEX HEAD SCREWS (18)
usin the L-WRENCH (15).
Step 4
Pae 10
15
N
QL
M
C
1-1/2" HEX HEAD SCREW
(4 used in this step)
18