Teknik Office Affiliate 5427468 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS
IMPORTANT SAFETY
INFORMATION.
PLEASE READ AND KEEP
FOR FUTURE REFERENCE.
Hudson Elm finish | Model 5427468
English pg 1-14
Français pg 15-17
Español pg 18-20
09/22/21 Lot # 566975
Purchased:
__________________
1800x900 Bow
Front Desk
Teknik
www.teknikoffice.co.uk

Table of Contents Assembly Tools Required
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Hardware Identification
Part Identification
Optional Accessories
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
2
3
4
6
5-14
15-17
18-20
21-22
23
Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
BLACK 1-15/16" FLAT HEAD SCREW - 6
113S
LEVELER - 8
46E WOOD DOWEL - 22 42F TOUCH-UP PEN - 1
10M GROMMET - 2 2P
CORD CLIP - 2
9P
GROMMET CAP- 2
3P
Page 2
TWIST-LOCK®
FASTENER COVER - 23
125P HOLE PLUG - 8 127P

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D RIGHT UPRIGHT (1)
E BACK (2)
F MODESTY PANEL (1)
G LEFT UPRIGHT (1)
A
B
C
D
E
F
GE
Page 3

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Insert fourteen WOOD DOWELS (42F) into the exact
holes shown in the TOP (C).
å NOTE: You may need to gently tap the WOOD DOWEL in
with your hammer.
å Push two CORD CLIPS (9P) into the TOP (C).
42F
9P
42F
C
Curved edge
Page 5

å Insert four WOOD DOWELS (42F) into the exact holes
shown in one BACK (E).
å NOTE: You may need to gently tap the WOOD DOWEL in
with your hammer.
å Fasten the RIGHT END (A) and RIGHT UPRIGHT (D) to
the BACK (E). Tighten six TWIST-LOCK® FASTENERS.
å NOTE: Be sure the WOOD DOWELS in the BACK insert
into the END and UPRIGHT.
Hardware Usage Guide
1. Insert the dowel end of the FASTENER into the
hole of the adjoining part.
NOTE: The dowel end of the FASTENER must
remain fully inserted in the hole of the adjoining
part while locking the FASTENER.
2. Tighten the FASTENER with a Phillips
screwdriver as tight as possible.
Dowel end
2.
Push a TWIST-LOCK® FASTENER
into the large hole in the part.
1.
HOW TO USE A TWIST-LOCK®FASTENER
Step 2
If the TWIST-LOCK® FASTENER
is already inserted in the part,
be sure both the dowel end and
fastener edge are straight.
A
D
E
42F
42F
Surface with
TWIST-LOCK®
FASTENERS
Surface without
TWIST-LOCK®
FASTENERS
This hole must be here.
Page 6

å Fasten the RIGHT END (A) and RIGHT UPRIGHT (D) to
the TOP (C). Tighten four TWIST-LOCK® FASTENERS.
å NOTE: Be sure the WOOD DOWELS in the TOP insert
into the END, UPRIGHT, and BACK (E).
Step 3
A
C
D
E
Curved edge
Page 7

å Fasten the MODESTY PANEL (F) to the TOP (C). Tighten
three TWIST-LOCK® FASTENERS.
Step 4
C
F
Surface with
TWIST-LOCK®
FASTENERS
Page 8

å Insert four WOOD DOWELS (42F) into the exact holes
shown in one BACK (E).
å NOTE: You may need to gently tap the WOOD DOWEL in
with your hammer.
å Fasten the LEFT END (B) and LEFT UPRIGHT (G) to the
BACK (E). Tighten six TWIST-LOCK® FASTENERS.
å NOTE: Be sure the WOOD DOWELS in the BACK insert
into the END and UPRIGHT.
Step 5
B
G
E
42F
42F
Surface with
TWIST-LOCK®
FASTENERS
Surface without
TWIST-LOCK®
FASTENERS
This hole must be here.
Page 9

å Fasten the LEFT END (B) and LEFT UPRIGHT (G) to the
TOP (C). Tighten four TWIST-LOCK® FASTENERS.
å NOTE: Be sure the WOOD DOWELS in the TOP insert
into the END, UPRIGHT, and BACK (E).
Step 6
C
B
E
G
Page 10

å Fasten the UPRIGHTS (D and G) to the MODESTY PANEL (F).
Use six BLACK 1-15/16" FLAT HEAD SCREWS (113S).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
Step 7
G
D
F
BLACK 1-15/16" FLAT HEAD SCREW
(6 used in this step)
113S
Page 11
113S