Teknik 5418793 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
ChalkedWood Computer Desk
Model 5418793
www.teknikoffice.co.uk
For all your
newfangled gadgetry.
Teknik

Table of Contents Assembly Tools Required
2-3
4-5
6-29
Part Identification
Hardware Identification
Assembly Steps
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
Page 2
Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C RIGHT UPRIGHT (1)
D LEFT UPRIGHT (1)
D102 LARGE DRAWER SIDE (2)
D214 SMALL DRAWER SIDE (2)
D340 SMALL DRAWER BOX FRONT (2)
D341 LARGE DRAWER BOX FRONT (2)
D930 DRAWER BOTTOM (2)
E TOP (1)
F RIGHT BOTTOM (2)
G LEFT BOTTOM (1)
H MODESTY PANEL (1)
I BACK (2)
J KEYBOARD BRACE (2)
K DOOR (1)
L ADJUSTABLE SHELF (1)
M2 LEG (4)
N KEYBOARD FRONT (1)
O KEYBOARD SHELF (1)
P LARGE DRAWER FRONT (1)
T SMALL DRAWER FRONT (1)
W BOTTOM MOLDING (2)
X FOOT (4)

Part Identification Now you know
our ABCs.
Page 3
A
B
C
D
E
F
G
H
I
J
K
L
M2
N
O
P
D341
T
D340
W
XD102
D214
D102
D930
D930
D214
D340
D341
J
M2
X
M2
X
M2
X
F
I
W

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 4
40CA CABINET RIGHT - 2 40CB CABINET LEFT - 2 40CC DRAWER RIGHT - 2 40CD DRAWER LEFT - 2
BLACK LEFT
DRAWER SLIDE - 1
DD
BLACK RIGHT
DRAWER SLIDE - 1
CC
BLACK LEFT
CABINET RAIL - 1
BB
BLACK RIGHT
CABINET RAIL - 1
AA
FILE GLIDE - 2
3B
12F TWIST-LOCK®
FASTENER - 2
METAL
BRACKET - 1
4G ANGLE
BRACKET - 4
44G
RUBBER
SLEEVE - 4
2R
METAL PIN - 8
1R
CORD CLIP - 1
4P
BACKPLATE - 1
125K
KEYBOARD
HINGE - 2
12H
CAM COVER - 10
33P
NAIL - 30
1N
CAM DOWEL - 20
2F
HIDDEN CAM - 32
1F CAM SCREW - 12 8F
LARGE RUBBER
SLEEVE - 1
58G
124K KNOB - 4
14H HINGE - 2
FILE ROD - 2
7B

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 5
BLACK 1-7/8" FLAT HEAD SCREW - 4
2S
BLACK 1-1/4" FLAT HEAD SCREW -16
7S
BLACK 9/16" LARGE HEAD SCREW - 9
1S
BLACK 1/2" FLAT HEAD SCREW - 4
11S
GOLD 5/16" FLAT HEAD SCREW - 20
3S
BLACK 1-1/8" MACHINE SCREW - 3
21S
BROWN 1" FLAT HEAD SCREW - 4
18S
BLACK 7/8" LARGE HEAD SCREW - 8
17S
BLACK 7/8" MACHINE SCREW - 1
37S
SILVER 5/8" FLAT HEAD SCREW - 4
23S
SILVER 9/16" LARGE HEAD SCREW - 2
54S
30S BLACK 1-9/16" FLAT HEAD SCREW - 4

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push two SAUDER TWIST-LOCK®
FASTENERS (12F) into the large holes in the
MODESTY PANEL (H).
Page 6
Do not tighten the TWIST-LOCK® FASTENERS in this step.
H
12F

å Push thirty-two HIDDEN CAMS (1F) into the ENDS (A and B),
UPRIGHTS (C and D), BOTTOMS (F and G), and KEYBOARD
BRACES (J). Then, insert a CAM DOWEL (2F) into each
HIDDEN CAM, except for the CAMS in the long edges of the
ENDS and UPRIGHTS.
Step 2
Page 7
Arrow
Arrow
(32 used)
(20 used)
Arrow
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not tighten the HIDDEN CAMS in this step.
Do not insert
CAM DOWELS
into these edges.
Do not insert
CAM DOWELS
into these edges.
1F
2F
1F
1F
A
B
C
D
F
G
J
J
F
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole

Step 3
å Fasten the CABINET RIGHTS (40CA) and CABINET
LEFTS (40CB) to the RIGHT END (A) and RIGHT
UPRIGHT (C). Use eight GOLD 5/16" FLAT HEAD
SCREWS (3S) through holes #1 and #3.
Page 8
A
C
1
2
3
4
1
2
34
Roller end
Roller end
1
2
3
4
1
2
34
Edge with
CAM DOWELS
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Remember:
Righty tighty.
Lefty loosey.
GOLD 5/16" FLAT HEAD SCREW
(8 used in this step)
3S

å Fasten the BLACK CABINET RAILS (AA and BB) to the
KEYBOARD BRACES (J). Use four GOLD 5/16" FLAT
HEAD SCREWS (3S).
å NOTE: The CABINET RAILS are marked "CABINET
RIGHT" and "CABINET LEFT" for easy identification.
Step 4
Page 9
J
J
BB
AA
Roller end
Roller end
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Edge with
CAM DOWELS
Edge with
CAM DOWELS
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S

Step 5
å Turn twelve CAM SCREWS (8F) into the LEGS (M2).
Page 10
Remember:
Righty tighty.
Lefty loosey.
(12 used)
8F
M2
M2
M2
M2