TMG TMG-ST2041CV User manual

Main Specifications :
20' X 40' SINGLE TRUSS STORAGE
CONTAINER SHELTER

▶WWW.TMGINDUSTRIAL.COM P 1/ 12 Toll F re e: 1 -877-761- 2 819
Main Specifications :
Overall assembled size : W6 x L12 x H2 (m) / 19.6 x 39.37 x 6.5(ft)
Ridge Peak Height : 2 m / 6.5ft + container height
Prior to assembly
Please read the instructions carefully before installation. It is very important to
follow your local safety regulations and industry standards during installation.
Regulations may include but are not limited to:
- Safety helmets, protective eyewear, and clothing
- Safety harnesses for all elevated workers
- Proper ladder, cage, and safety operation
Check all components and parts before installation. All parts are marked with a part
number, please refer to the parts list to make sure you have all parts.
Choose a day with low or no wind to install, assembly is hard in heavy wind. Do not
make any alterations to the structure. Do not hang any weights on the frame during
installation, including parts. We are not responsible for any damages or injuries caused by
inappropriate installation, unauthorized modifications or extreme weather.
This building is not intended for human occupancy.
It is recommended to use heavy duty duct tapes to tape the tube connection joint
spots to protect the cover from damage and worn. It will help to extend the cover
life span.
Check the parts list below to make sure all parts are received prior to assembly.

▶WWW.TMG IN DUST RI AL .C OM P 2 /12 T o l l F re e: 1 -877-761- 2 81 9
TMG-ST2041CV Part List
Parts
code
Graphical
Description
length
Qty
1
Dome arch pipe
φ48xL2192mm
11
2
Middle rafter tube
φ48xL1481mm
22
3
Shoulder tube
φ48xL1428mm
22
4
Roof purlin
(horizontal tube)
φ42xL1148mm
50
4A
Middle truss connectors
W50xL170mm
90
4B
Front and rear connectors
W50xL111mm
10
5
Middle truss baseplate
W150xL200mm
18
5L
Left corner baseplate
(front and rear truss)
W150xL200mm
2
5R
Right corner baseplate
(front and rear truss)
W150xL200mm
2
6
Top cover tension tube A
φ32xL2093mm
10
6A
Top cover tension tube B
φ32xL1930mm
2
12
Top cover
W8.52xL12.74m
1
13
Ratchet
2T
22
13A
Tie down straps
W30xL800mm
22

▶WWW.TMG IN DUST RI AL .C OM P 3 /12 T o l l F re e: 1 -877-761- 2 81 9
14
Braided rope
φ8x60m
1 bundle
15
Scratch resistant tape
10m
2
16
Half round head bolt
M10x80mm
100
17
Hex bolt
M10x70mm
132
18
Water plug
φ32mm
4
20
Self tapping screw
#12x25mm
55

▶WWW.TMG IN DUST RI AL .C OM P 4 /12 T o l l F re e: 1 -877-761- 2 81 9
Step 1 : Baseplate positioning and installation.
1
Parts
code
Graphical
Qty
5
18
5L
2
5R
2

▶WWW.TMG IN DUST RI AL .C OM P 5 /12 T o l l F re e: 1 -877-761- 2 81 9
Step 2 : Install 11 sets of trusses.
Parts
code
Graphical
Qty
1
1x11
2
2x11
3
2x11
17
8x11

▶WWW.TMG IN DUST RI AL .C OM P 6 /12 T o l l F re e: 1 -877-761- 2 81 9
Step 3 : Wrap (#15) around the sharp points of the joint to avoid friction between
the fabric and the interface.
Parts
code
Graphical
Qty
15
2

▶WWW.TMG IN DUST RI AL .C OM P 7 /12 T o l l F re e: 1 -877-761- 2 81 9
Step 4 : Put up all trusses.
Parts
code
Graphical
Qty
17
44

▶WWW.TMG IN DUST RI AL .C OM P 8 /12 T o l l F re e: 1 -877-761- 2 81 9
Step 5 : Installation of roof purlin.
Parts
code
Graphical
Qty
4
50
4A
90
4B
10
16
100
19
100

▶WWW.TMG IN DUST RI AL .C OM P 9 /12 T o l l F re e: 1 -877-761- 2 81 9
Step 6 : Install the cover.
Parts
code
Graphical
Qty
12
1

▶WW W.TM GIND USTRIA L.C OM P 10/12 T ol l F ree :1 -877-761-2819
Step 7 : Install metal pipes on both sides.
Parts
code
Graphical
Qty
6
10
6A
2
18
4

▶WW W.TM GIND USTRIA L.C OM P 11/12 T ol l F ree :1 -877-761-2819
Step 8 : Tension the top cloth with tensioning device and braided rope.
Parts
code
Graphical
Qty
13
22
13A
22
14
1 bundle

▶WW W.TM GIND USTRIA L.C OM P 12/12 T ol l F ree :1 -877-761-2819
After Installation
Walk around and inspect the building periodically to make sure the parts are firmly
fixed and the whole building is well supported. Check all bolts and hardware
connectors to make sure they are in place and tightened. Check the base plates,
adjust the ropes if necessary and clean the cover regularly.
Snow accumulating on the fabric cover must be removed as soon as possible. If
snow is allowed to become solid ice on the cover, it could increase the weight on the
roof and collapse the building or reduce the life span.
We strongly recommend you remove any snow from the roof immediately. Do not leave
any snow load on the roof overnight. Keep 3 feet of clearance on all sides at all times. Do
not allow snow to accumulate and pile up on the sides of the building. Otherwise the
pressure from the sides will push inwards and could lead to a collapse.