Uplus Lighting 6 EYE RETRO BAR User manual

User manual
6 EYE RETRO BAR
Please read the instructions carefully before use

2
TABLE OF CONTENTS
1. Safety Instructions………………………………………………………………………………3
Technical Specifications…………………………………………………………………………4
Control Menu ………………………………………………………………………………………4
DMX Channels ……………………………………………………………………………………5-6
Trouble Shooting……………………………………………………………………………………7
Fixture Cleaning………………………………………………………… …………………………7
STATEMENT
The product has well capability and intact packing when leave factory. All of the user should
comply with warning item and manual, any misuse cause of the damages are not included in our
guarantee, and also can not be responsible for any malfunction & problem owing to ignore the
manual.

3
1.Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also
receive this instruction booklet.
•Unpack and check carefully there is no transportation damage before using the unit.
•Before operating, ensure that the voltage and frequency of power supply match the power requirements of the
unit.
•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
•The unit is for indoor use only. Use only in a dry location.
•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent surfaces. Be sure
that no ventilation slots are blocked.
•Disconnect main power before replacement or servicing.
•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always by taking its
base.
•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher than this Unit
surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand during its operation. Turn off
the power and allow about 15 minutes for the unit to cool down before replacing or serving.
•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit by yourself.
Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized
technical assistance center. Always use the same type spare parts.
•DO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:
•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution:
•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any repairs yourself. In
the unlikely event your unit may require service, please contact your nearest dealer.
Installation:
•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid
vibration and slipping while operating. And make sure that the structure to which you are attaching the unit is
secure and is able to support a weight of 10 times of the unit’s weight. Also always use a safety cable that can
hold 12 times of the weight of the unit when installing the fixture.
•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the touch of
people.

4
2.Technical Specifications
SPECIFICATIONS:
Light Source: 6*60W & 144*0.2w 3in1 led
Input Voltage:AC90-260V 50/60Hz
Power Consumption: 420W
Control mode:DMX512,Auto-run , Master-Slave
Control Channel: 8/28 channels
Powercon:powercon in & out
DMX sockets:3-pin XLR sockets
Display: Digital Display
Strobe：1-25t/s multiple stroboscopic effect
Dimming：0-100% linear dimmer
3.Control Menu
Menu Operation
On the base of the control panel offers a number of features, such as setting DMX fixture address,
switch the lamp, run the test program, the mode selection.
No
Show
Instruction
1
A001
001-512
2
Channel
8CH
28CH
3
DMX512,Auto-run , Master-Slave
DMX512,Auto-run , Master-Slave

5
4.DMX Channels
8 DMX channels
CH 8
DMX Value
Function
Function Illustration
1
0－255
Total Dimmer
Total Dimmer
2
0－3
Strobe
No function
4－255
Slow to fast
3
0-255
Red
R Dimmer dark to light
4
0-255
Green
G Dimmer dark to light
5
0-255
Blue
B Dimmer dark to light
6
0-255
White
W Dimmer dark to light
7
0-9
Function
No function
10-19
Effect 1
20-29
Effect 2
…
10 numbers one effect
240-249
Effect 24
250-255
Effect 25
8
0-63
speed
static
64-159
Forward running speed from fast to slow
160-255
Reverse running speed from slow to fast
28 DMX channels
CH 28
DMX Value
Function
Function Illustration
1
0－255
Total Dimmer
Total Dimmer
2
0－3
Strobe
No function
4－255
Slow to fast
3
0-255
Red 1
R1 Dimmer dark to light
4
0-255
Green1
G1 Dimmer dark to light
5
0-255
Blue1
B1 Dimmer dark to light
6
0-255
White1
W1 Dimmer dark to light
7
0-255
Red2
R2 Dimmer dark to light
8
0-255
Green2
G2 Dimmer dark to light
9
0-255
Blue2
B2 Dimmer dark to light
10
0-255
White2
W2 Dimmer dark to light
11
0-255
Red3
R3 Dimmer dark to light
12
0-255
Green3
G3 Dimmer dark to light
13
0-255
Blue3
B3 Dimmer dark to light
14
0-255
White3
W3 Dimmer dark to light
15
0-255
Red4
R4 Dimmer dark to light
16
0-255
Green4
G4 Dimmer dark to light

6
17
0-255
Blue4
B4 Dimmer dark to light
18
0-255
White4
W4 Dimmer dark to light
19
0-255
Red5
R5 Dimmer dark to light
20
0-255
Green5
G5 Dimmer dark to light
21
0-255
Blue5
B5 Dimmer dark to light
22
0-255
White5
W5 Dimmer dark to light
23
0-255
Red6
R6 Dimmer dark to light
24
0-255
Green6
G6 Dimmer dark to light
25
0-255
Blue6
B6 Dimmer dark to light
26
0-255
White6
W6 Dimmer dark to light
27
0-9
Function
No function
10-19
Effect 1
20-29
Effect 2
…
10 numbers one effect
240-249
Effect 24
250-255
Effect 25
28
0-63
speed
static
64-159
Forward running speed from fast to slow
160-255
Reverse running speed from slow to fast

7
5.Trouble Shooting
F ollo w ing a r e a few c o mm on p r oble m s th a t m a y occu r d uring ope r a tion . He r e a r e s o m e s ug g es tion s fo r
ea s y tr ou b leshooting :
A. The un it does no t work , no li ght a n d t he f a n d o es no t w o r k
1. Check th e c on nect ion of p owe r a nd m a in fu s e .
2. M eas ure th e m a ins volt a ge on th e m a i n co nn e ct o r .
3. Check th e pow er on LED .
B. N o t responding t o D MX c on t ro ll er
1. D M X LED s h ou ld b e on. If no t, che ck D M X co n nectors, ca b l es to s ee if link p r ope r ly .
2. If th e D M X LE D i s on a nd no r espons e t o th e c h a nn el, che ck th e a dd r ess s etti ng s a nd D M X p ol a r ity .
3. If y ou h a ve i nter m ittent D M X s ig n a l p r oble m s , che ck th e p ins on c onn ecto r s or on
PCB of th e u nit or the p r ev iou s on e.
4. Tr y to us e a no th er D M X co ntroller .
5. Check if th e D M X ca b le s r un ne a r or run a lon g s id e t o h ig h volta ge c a b les th a t m a y c a us e d a m a ge or
in terfer ence to D M X inter face circui t.
C . One of the cha nn el s is no t w o r k ing w el l
1. Th e s tep p er moto r m ig h t b e dam a g ed or the c a b le c on nect ed to th e PCB is b r oken.
2. Th e m oto r ’ s d r ive IC on th e PCB m ig h t b e o ut of co ndition
6.Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.