Uplus Lighting 200 LED BSW User manual

User manual
200 LED BSW
Please read the instructions carefully before use

2
TABLE OF CONTENTS
1. Safety Instructions……………………………………………………………………………3-4
2.Technical Specifications…………………………………………………………………………4
3.Control Menu ……………………………………………………………………………………5-6
4.DMX Channels ……………………………………………………………………………………7-8
5.Dimension …………………………………………………………………………………………9
6.Trouble Shooting…………………………………………………………………………………10
7.Fixture Cleaning………………………………………………………… ………………………10
STATEMENT
The product has well capability and intact packing when leave factory. All of the user should
comply with warning item and manual, any misuse cause of the damages are not included in our
guarantee, and also can not be responsible for any malfunction & problem owing to ignore the
manual.

3
1.Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure
that they also receive this instruction booklet.
•Unpack and check carefully there is no transportation damage before using the unit.
•Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
•The unit is for indoor use only. Use only in a dry location.
•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Disconnect main power before replacement or servicing.
•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always
by taking its base.
•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher
than this Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand
during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before
replacing or serving.
•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit
by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
•DO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:
•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution:
•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any
repairs yourself. In the unlikely event your unit may require service, please contact your nearest
dealer.
Installation:
•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is

4
firmly fixed to avoid vibration and slipping while operating. And make sure that the structure to
which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s
weight. Also always use a safety cable that can hold 12 times of the weight of the unit when
installing the fixture.
•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the
touch of people.
2.Technical Specifications
Light Sources: 200W High Power White LED
Max Power Consumption: 290W
Power Input: 100-240V, 50/60Hz
Color Tempreture: 7500K
LED Lifespan: 50000 hours
Operating mode: DMX512,Auto, Sound active, Master/slave
Channel mode: 18 DMX512 Channel
Pan: 540°(16bit) Electric correction
Tilt：270° (16bit) Electric correction
Color wheel:9 colors + open, with rainbow effect
Gobo wheel：10 gobos + open, with rotation and running water effect
Rotation gobo wheel:7 gobos+open
Prism: 4 facet prism with bi-direction rotating
0-100% linear dimming, fit advanced iris aperture zoom effect, fast, precise, smooth, one of the most
advanced optical system in the same class of products.
Strobe: 0-25Hz/s, sync pulse strobe, random pulse stroboscopic,etc.
Frost: With frost effect
Zoom range:7°-21°
Display: Touch screen, English and Chinese interchangeable, reversible display.
Over heat protection
IP level: IP20
Packing Size: 343*232*537mm
N.W：15kgs
Gross weight: 18kgs

5
3.Control Menu
Menu Operation
On the base of the control panel offers a number of features, such as setting DMX fixture address,
switch the lamp, run the test program, the mode selection.
Main Menu
Second Menu
Third Menu
Forth Menu
Settings
Dmx Address
1 - 512
Fixture Set
Dmx Mode
STD / EXT
Run Mode
DMX / Host
Pan Inverse
Close / Open
Tilt Inverse
Close / Open
Display
Language
CH / EN
Display Flip
Close / Open
Display Mode
Show / 60s
Reset
XY Reset
Cance / Run
Motor Reset
Cance / Run
All Reset
Cance / Run
Factory
Cance / Run
Info
Time
Current Time
xxxH
Show Time
xxxH
Power Count
xxx
Sensor
xxxxxx
Software Version
Panel
Vx.xxx

6
Motor_XY
Vx.xxx
Motor
Vx.xxx
Manual
Pan
0 - 255
PanFine
0 - 255
Tilt
0 - 255
TiltFine
0 - 255
⁞
⁞
Factory
Password
0 - 255
Pan
0 - 255
Tilt
0 - 255
Iris
0 - 255
Color
0 - 255
RotGobo
0 - 255
Gobo Rot
0 - 255
Fix Gobo
0 - 255
Frost
0 - 255
Color7
0 - 255
Effect
0 - 255
Prism
0 - 255
PrismRot
0 - 255
Zoom
0 - 255
Focus
0 - 255
4.DMX Channels

7
Model – CH18
Channel
DMX Value
Dispaly
Function
1
0－255
Pan
Pan 0-540°
2
0－255
Pan fine
Pan fine 16bit
3
0－255
Tilt
Tilt 0-240°
4
0－255
Tilt fine
Tilt fine 16bit
5
0－255
P/T Speed
from fast to slow
6
0－255
Dimming
From dark to bright
7
0－3
Strobe
Open
4－99
Synchronous strobe
100－149
Split strobe
150－199
Strobe
200－249
Random strobe
250－255
Open
8
0－19
Color
Color 1 Linear
20－39
Color 2 Linear
…………
…………
…………
…………
160－179
Color 9 Linear
180－199
Blank linear change
200－226
Color flow clockwise, from fast to slow
227－228
Stop
229－255
Color flow counterclockwise, from slow to fast
9
0－4
Fixed gobo
blank
5－54
10 fixed patterns, every 5 numbers correspond to a
pattern
55－154
10 fixed patterns jitter fast to slow, every 10 numbers
correspond to a pattern
155－204
Flowing in a clockwise pattern, from fast to slow
205－205
Stop
206－255
Color flow counterclockwise, from slow to fast
10
0－79
Rotary gobo
7 rotating patterns + blank, every 10 numbers
correspond to a pattern
80－159
7 rotating patterns + blank jitter fast to slow
160－206
Flowing in a clockwise pattern, from fast to slow
207－208
Stop
209－255
Flowing in a counterclockwise pattern, from slow to
fast
11
0－1277
Rotary gobo
rotation fine
Gobo rotation 0-360 degrees
128－191
The pattern rotates clockwise from fast to slow
192－193
Stop

8
194－255
The pattern turns counterclockwise from slow to fast
12
0-127
Prism insertion
Prism removed
128-255
Prism insertion
13
0-127
Prism rotation
Prism rotates 90 degrees
128-190
The pattern rotates clockwise from fast to slow
191-192
Stop
193-255
The pattern turns counterclockwise from slow to fast
14
0-127
Frost
white
128-255
Frost
15
0-255
Zoom
0-100% linear Zoom
16
0-255
enlarge
0-100% linear Enlarge
17
0-50
Macro function
No
51-100
System self-check
101-150
Auto-run 1
151-200
Auto-run 2
201-255
Sound
18
0-250
No
251-255
Reset (hold for 5 seconds to take effect)
5.Dimension

9

10
6.Trouble Shooting
F ollo w ing a r e a few c o mm on p r oble m s th a t m a y occu r d uring ope r a tion . He r e a r e s o m e s ug g es tion s fo r
ea s y tr ou b leshooting :
A. The un it does no t work , no li ght a n d t he f a n d o es no t w o r k
1. Check th e c on nect ion of p owe r a nd m a in fu s e .
2. M eas ure th e m a ins volt a ge on th e m a i n co nn e ct o r .
3. Check th e pow er on LED .
B. N o t responding t o D MX c on t ro ll er
1. D M X LED s h ou ld b e on. If no t, che ck D M X co n nectors, ca b l es to s ee if link p r ope r ly .
2. If th e D M X LE D i s on a nd no r espons e t o th e c h a nn el, che ck th e a dd r ess s etti ng s a nd D M X
p ol a r ity .
3. If y ou h a ve i nter m ittent D M X s ig n a l p r oble m s , che ck th e p ins on c onn ecto r s or on
PCB of th e u nit or the p r ev iou s on e.
4. Tr y to us e a no th er D M X co ntroller .
5. Check if th e D M X ca b le s r un ne a r or run a lon g s id e t o h ig h volta ge c a b les th a t m a y c a us e d a m a ge or
in terfer ence to D M X inter face circui t.
C . One of the cha nn el s is no t w o r k ing w el l
1. Th e s tep p er moto r m ig h t b e dam a g ed or the c a b le c on nect ed to th e PCB is b r oken.
2. Th e m oto r ’ s d r ive IC on th e PCB m ig h t b e o ut of co ndition
7.Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates:
damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics .
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.