Uplus Lighting 250 BEAM User manual

User manual
250 BEAM
Please read the instructions carefully before use

2
TABLE OF CONTENTS
1. Safety Instructions……………………………………………………………………………3-4
Technical Specifications…………………………………………………………………………4
Control Menu ……………………………………………………………………………………5-6
DMX Channels ……………………………………………………………………………………6-9
Trouble Shooting…………………………………………………………………………………10
Fixture Cleaning………………………………………………………… ………………………10
STATEMENT
The product has well capability and intact packing when leave factory. All of the user should
comply with warning item and manual, any misuse cause of the damages are not included in our
guarantee, and also can not be responsible for any malfunction & problem owing to ignore the
manual.

3
1.Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
•Unpack and check carefully there is no transportation damage before using the unit.
•Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
•The unit is for indoor use only. Use only in a dry location.
•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Disconnect main power before replacement or servicing.
•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always
by taking its base.
•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher
than this Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand
during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before
replacing or serving.
•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit
by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
•DO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:
•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution:
•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any
repairs yourself. In the unlikely event your unit may require service, please contact your nearest
dealer.
Installation:
•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly

4
fixed to avoid vibration and slipping while operating. And make sure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also
always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.
•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the
touch of people.
2.Technical Specifications
Ballast: E-ballast
Light source: 250W bulb
Color temperature: 8500 k
The life of the bulb: 2000 hours
Voltage: AC110-240v
Frequency: 50 /60 hz
Total power: 450 w
Prism: Double prism effect, one 24 prism+one 8 prism, two prism can be superimposed
Color wheel: 13 colors+white, with rotating rainbow effect, a six-color plate for rainbow effect
Gobo wheel: 17 gobos+ white, with rotating gradient effect and gobo swing effect Strobe: up to 13
times per second with randon pulse strobe
Movement: Pan 540°; Tilt: 250°(16 bit scanning)
Dimming:0-100% linear adjustment
Atomization: 0-100% linear atomization
Control signal: international standard DMX512
Channel mode: 16/20 channel model
Protection grade: IP20
Dimension:320x230x530mm; NW:16 kg

5
3.Control Menu
Menu Operation
On the base of the control panel offers a number of features, such as setting DMX fixture address,
switch the lamp, run the test program, the mode selection.
Main Menu
Second
Third
Fourth
Dmx Address
000 - 512
Fixture
Dmx Mode
STD / EXT
Run Mode
DMX / Host
Pan Invert
Close / Open
Tilt Invert
Close / Open
Lamp On Power
Close / Open
Lamp Control
Close / Open
Manual
Color
000 - 255
Strobe
000 - 255
Dimmer
000 - 255
Fix Gobo
000 - 255
⁞
⁞
Information
Time
Current Time
xxxH
Total Time
xxxH
Power Count
xxx
Sensor
Pan
Tilt
Temp

6
⁞
Software Version
Panel
Vx.xx
Motor1
Vx.xx
Motor2
Vx.xx
Factory
Password
000 - 255
Pan
000 - 255
Tilt
000 - 255
Strobe
000 - 255
Color
000 - 255
Fix Gobo
000 - 255
⁞
⁞
Fixture Reset
XY Reset
OFF / Run
Motor Reset
OFF / Run
All Reset
OFF / Run
Factory
OFF / Run
Display
Language
CH / EN
Display Flip
Normal / Reverse
Display Mode
60s / Show
4.DMX Channels
Model - CH16/CH20
Standard mode
（16CH)
Extended mode
（20CH）
DMX Value
Function
1
1
Color
0-4
White
5-9
White+Color1
10-14
Color1
15-19
Color1+Color2
20-24
Color2
25-29
Color3+Color3
30-34
Color3

7
35-39
Color3+Color4
40-44
Color4
45-49
Color4+Color5
50-54
Color5
55-59
Color5+Color6
60-64
Color6
65-69
Color6+Color7
70-74
Color7
75-79
Color7+Color8
80-84
Color8
85-89
Color8+Color9
90-94
Color9
95-99
Color9+Color10
100-104
Color10
105-109
Color10+Color11
110-114
Color11
115-119
Color11+Color12
120-124
Color12
125-129
Color12+Color13
130-134
Color13
135-139
Color13+White
140-149
White
150-199
FAST ROTATION - SLOW ROTATION
200-205
STOP
206-255
SLOW ROTATION - FAST ROTATION
2
2
Shutter
0-3
Closed
4-103
SLOW - FAST
104-107
Open
108-207
FAST STROBE-SLOW STROBE
208-212
Open
213-251
RANDOM SLOW - FAST
252-255
Open
3
3
Dimmer

8
0－255
Linear Dimmer
4
4
Gobo 1
0-4
white
5-9
Gobo 1
10-14
Gobo 2
15-19
Gobo 3
20-24
Gobo 4
25-29
Gobo 5
30-34
Gobo 6
35-39
Gobo 7
40-44
Gobo 8
45-49
Gobo 9
50-54
Gobo 10
55-59
Gobo 11
60-64
Gobo 12
65-69
Gobo 13
70-79
Gobo 1 Jitter
80-89
Gobo 2 Jitter
90-99
Gobo 3 Jitter
100-109
Gobo 4 Jitter
110-119
Gobo 5 Jitter
120-129
Gobo 6 Jitter
130-139
Gobo 7 Jitter
140-149
Gobo 8 Jitter
150-159
Gobo 9 Jitter
160-169
Gobo 10 Jitter
170-179
Gobo 11 Jitter
180-189
Gobo 12 Jitter
190-199
Gobo 13 Jitter
200-225
FAST ROTATION - SLOW ROTATION
226-229
STOP
230-255
SLOW ROTATION - FAST ROTATION
5
5
Prism1
0-127
Reserve

9
128-255
prism1
6
6
Prism2
0-127
Reserve
128-255
prism2
7
7
Prism-2 Rot
0－127
Rotation
128-190
FAST ROTATION - SLOW ROTATION
191-192
STOP
193-255
SLOW ROTATION - FAST ROTATION
8
8
Frost
0-127
white
128-191
Frost
192-255
6 Colors
9
9
Foucs
0-255
Foucs，Linear
10
10
0－255
Pan 8bit
11
11
0－255
Pan 16bit
12
12
0－255
Tilt 8bit
13
13
0－255
Tilt 16bit
14
14
0－255
P/T Speed
15
15
Reset
50-99
Pan&Tilt Reset
100-149
Effect Reset
150-199
All Reset
16
16
Function
100-149
Lamp ON
150-199
Lamp OFF
*
17
0－255
Reserve
*
18
Color speed
0-255
Fast to Slow
*
19
Gobo speed
0-255
Fast to Slow
*
20
Focus speed
0-255
Fast to Slow

10
5.Trouble Shooting
F ollo w ing a r e a few c o mm on p r oble m s th a t m a y occu r d uring ope r a tion . He r e a r e s o m e s ug g es tion s fo r
ea s y tr ou b leshooting :
A. The un it does no t work , no li ght a n d t he f a n d o es no t w o r k
1. Check th e c on nect ion of p owe r a nd m a in fu s e .
2. M eas ure th e m a ins volt a ge on th e m a i n co nn e ct o r .
3. Check th e pow er on LED .
B. N o t responding t o D MX c on t ro ll er
1. D M X LED s h ou ld b e on. If no t, che ck D M X co n nectors, ca b l es to s ee if link p r ope r ly .
2. If th e D M X LE D i s on a nd no r espons e t o th e c h a nn el, che ck th e a dd r ess s etti ng s a nd D M X p ol a r ity .
3. If y ou h a ve i nter m ittent D M X s ig n a l p r oble m s , che ck th e p ins on c onn ecto r s or on
PCB of th e u nit or the p r ev iou s on e.
4. Tr y to us e a no th er D M X co ntroller .
5. Check if th e D M X ca b le s r un ne a r or run a lon g s id e t o h ig h volta ge c a b les th a t m a y c a us e d a m a ge or
in terfer ence to D M X inter face circui t.
C . One of the cha nn el s is no t w o r k ing w el l
1. Th e s tep p er moto r m ig h t b e dam a g ed or the c a b le c on nect ed to th e PCB is b r oken.
2. Th e m oto r ’ s d r ive IC on th e PCB m ig h t b e o ut of co ndition
6.Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.