VENETA 65101-40159 Instruction sheet

Required Tools measuring
tape
drill with
2mm bit
phillips bit or
screwdriver
pencil knife
How to install your
#65101-40159
Cordless
(Roller Blinds with No top treatment) Difficulty:
32mm Round
Head Screw
(for Blind Bracket)
19mm Round Head
Screw
Blind Bracket
(on Tension Dial)
Blind Bracket
(on End Plug end)
Blind Bracket
Cover
Handle
Traditional Hold
Down Bracket
(Optional)
Included Hardware
The hardware can be found in
the small hardware box included
with your blind.
1
1Blind Bracket Installation
①
②
③
Installing inside the window frame…
When installing the blind bracket, the distance from the bracket’s front mounting hole to the
front edge of the window frame should be at least 19mm.
Make sure both blind brackets line up with each other horizontally.
First fit the blind bracket cover over the blind bracket, and then screw brackets into wall.
Each blind bracket will require two 32mm round head screws for the installation.
①
②
③
④
Installing outside the window frame…
Blind Brackets Installation Tips…
When installing the blind bracket, the distance from the bracket’s front mounting hole to the
front edge of the window frame should be at least 19mm.
Make sure both blind brackets line up with each other horizontally.
Each blind bracket will require two 32mm round head screws for the installation.
Fit the blind bracket cover over the blind bracket.
①
②
The top & bottom of left & right blind brackets should be at the same horizontal line.
The front & back of left & right blind brackets should be at the same horizontal line.
1
④
≥19mm
≥19mm

①
Installation of the Blind…
First, insert the tension dial into the tongue of tension
dial bracket.
②Second, press the end plug and insert the end plug
end into the hole of bracket of the other side.
③
①
②
③
2Blind Installation and Removal
Installation
continued…
Blind Installation Tips…
After blind is installed into blind brackets, use a level to check if the fabrics roll is horizontal; if not,
please adjust the position of blind brackets to keep the fabrics roll level.
The blind needs to be level.
The gap on end plug end needs
to be about 4.5mm.
4.5mm
How to install your
#65101-40159
Cordless
(Roller Blinds with No top treatment) Difficulty:
2
①
②
The lock pin in the blind bracket
must be slide downward into the
end plug to prevent the blind
from falling.
Align tension dial of
the blind with the
tongue of the
tension dial bracket.
① ② ③
Removal of the Blind…
Use a tool to push the lock pin on end plug bracket upward.
Use tool to draw back the end plug from bracket.
Finally remove blind from mounting bracket.
Finally slide the lock pin in the blind bracket downward into the end plug to prevent the
blind from falling.

4Hold Down Brackets Installation (optional)
Use 19mm round head screw to secure each bracket.
Attach Handle to Hem Bar…
Step 1: Turn over hem bar and you can see a label attached at the center of the hem bar.
Step 2: Align the center of the bottom of the handle with the label.
Step 3: Hook the handle to the hem bar from top to bottom.
Step 4: Press the handle from top to bottom to make the top of the handle clip into the hem bar.
Step 5: Tear off the label from hem bar.
Installation
continued…
3Handle installation and Removal
How to install your
#65101-40159
Cordless
(Roller Blinds with No top treatment) Difficulty:
3
① ②
③
Label
The center of handle should
be aligned with the label.
④ ⑤
Remove handle from hem bar…
Use straight screwdriver to pry the bottom of handle
from hem bar and then the handle can be removed.

Installation
continued…
5Cordless Operation
How to install, operate and maintain your
#65101-40159
Cordless
(Roller Blinds with No top treatment) Difficulty:
4
Pull the handle downwards or upwards
and the blind will be lowered or raised.
The tension in our cordless roller blind can be adjusted to
provide optimal light control and to ensure easy and
dependable operation on a variety of window types and
sizes. If a cordless blind begins to slide down on its own or it
fails to roll up, the issue can be easily fixed by turning the
adjustment dial towards “+” to increase the tension.
Conversely, if the cordless blind cannot stop at the desired
height and tends to roll up by itself, the tension can be
decreased by turning the adjustment dial towards the “-”.
It is suggested to make the adjustments when blinds are
installed and fabrics are fully lowered.
Use the “hook” portion to hook
the handle to lower the blinds.
Place the U- shape channel of
pole under the handle and push
up to lift the blinds.
Great Job… Enjoy your new Veneta Blinds!
Please write a review on our
website at…
www.venetablinds.com.au
Feedback?
We would love to know how you
went with your installation…
1Dusting
Dust can be removed using a feather duster or vacuum with brush attachment on low suction.
2Spot Cleaning
Use a warm damp cloth or a mild detergent for tougher stains.
Dab the affected area, but do not rub the fabric. Finish with just a warm damp cloth.
Allow the fabric to dry in the lowered position.
Need HELP?
Call our
Customer Service team
for assistance
1300 836 382
Maintaining your
Blind