VENETA Vertical Honeycomb Blind User manual

#65101-10242-D
Handle
Bottom Bracket
Medium & Long
Screws for Wood
Clips & Rollers
Bolt
How to install your
Vertical Honeycomb Blind
measuring
tape
drill with
2mm bit
phillips bit or
screwdriver
pencil knife
Required Tools
Installation
Bracket
Installation Bracket
Head Rail
End Cap
Fixed
Vertical Rail
Bottom Bracket Fabric
Handle
Movable
Vertical Rail
Cord
Bead
Clips & Rollers
Support Shaft
Wall Plugs for Brick
or Cement using
a 6mm bit
(if requested)
Included Hardware
The hardware can be found in
the end of every box.
Difficulty: ★★★★☆
1

80mm
80mm
How to install your
Vertical Honeycomb Blind
2
Head Rail
4
Fixed Vertical Rail
3
Clips & Rollers
1
Installation Brackets
Installing inside the window frame…
At top of window or door frame, measure 80mm
in from each end and mark with a pencil. This is
the edge of the outer brackets.
Place brackets in position flush with the front
of the window opening and mark where the
screws will go.
We recommend drilling pilot holes for the
screws using a 2mm bit.
Fix the brackets into position using 2 long screws for each bracket.
If more brackets are supplied, space them evenly between the first two brackets.
Installing outside the window frame…
Measure 80mm in from top left and top right of where blind will sit (normally edge of
architrave) and mark with a pencil. This is the edge of the outer brackets.
Position the top of bracket 3mm above the architrave and mark where the screws will go.
We recommend using a spirit level to align brackets if not installing on the architrave.
We recommend drilling pilot holes for the screws using a 2mm bit.
Fix the brackets into position using 2 long screws for each bracket.
If more brackets are supplied, space them evenly between the first two brackets.
Position the top lip of the headrail under
the top front lip of the brackets as per
diagram to the right.
Push the headrail up at the back to click
into position as per diagram to the right.
Note: Do not untie the cords at the top of the
vertical rail.
Position the vertical rail up into the slots at the
back of headrail as per photo.
Lock the vertical rail into place by screwing the
bolt until firm (note the screw does not screw
into anything and will still be loose).
Attach clips to rollers (clips are attached to top of fabric).
Please write a review on our
website at…
www.venetablinds.com.au
Feedback?
We would love to know how you
went with your installation…
Installation bracket
Head rail
Side view
Need HELP?
Call our
Customer Service team
for assistance
1300 836 382
2

#65101-10242-D
How to install your
Vertical Honeycomb Blind
5
Movable Vertical Rail
7
Bottom Bracket
6
Fabric Clips and Rollers
8
Tension Cord
Note: for Centre Opening and Day&Night model, repeat steps 3 to 7 for the other side of the blind.
From the drawings below, decide which way you will face the bottom bracket
to be screwed to the wall or the floor.
Tilt the bottom of the fixed vertical rail out into the room and insert the bottom
bracket into the slot in the bottom of the fixed vertical rail.
We recommend drilling a pilot hole for the screw using a 2mm bit.
Fix the bracket into place using a medium screw.
Note: photo on right is taken from the rear of the blind.
Note: Slide the support shaft along the head rail to the
required spot.
Align the movable vertical rail to the sliding
support shaft in head rail.
Insert and screw the bolt until firm.
Press onto headrail from the front of the blind.
NOTE: The rollers should be facing away from you.
Remove the rubber band from the cord and bead.
Place the bead inside the bead housing from above, at the opposite
end of the head rail to the fixed vertical rail.
Note: focus on sliding the string down the slot.
3

How to install, operate and maintain your
Vertical Honeycomb Blind
9
Vertical Alignment
If the movable vertical rail is not vertical, adjust the screw as per photo.
Turn the screw either clockwise or anti-clockwise to make the rail vertical.
Note: the fabric can be crinkled and will bounce back into place.
10
Handle
Slide the handle onto the movable vertical rail.
Great Job… Enjoy your new Veneta Blinds!
Operating your
Blind
Maintaining your
Blind
To operate the blind simply slide the blind using the handle.
Use a warm damp cloth or a mild detergent for tougher stains.
Dab the affected area, but do not rub the fabric. Finish with just a warm damp cloth.
Allow the fabric to dry in the closed position.
3
Spot Cleaning
If ultrasonically cleaning the blind please specify that a mild solution must be used.
Note the rails should never be immersed in liquid.
4
Ultrasonic Cleaning
Please write a review on our
website at…
www.venetablinds.com.au
Feedback?
We would love to know how you
went with your installation…
1Removing your blind
Remove the blanket from the head rail.
Hold the blanket, and then to remove the vertical rail from the head rail.
Refer to below guide to remove the head rail.
a. Position a flat head screw driver between the back of the headrail and bracket.
b.Push screw driver upwards
c.Pull back of headrail down to unclip bracket from headrail.
d.Repeat for all other brackets.
Dust can be removed using a feather duster or vacuum with brush attachment
on low suction.
2
Dusting
4