VENETA Smartfit Honeycomb Blind User manual

How to install your
Smartfit Honeycomb Blind (25mm Cell)
Included Hardware
measuring
tape
drill with
2mm bit
phillips bit or
screwdriver
pencil knife
The hardware can be found in
the end of every box.
1Installation Brackets
Installing inside the window frame…
At top and bottom of window frame measure at least 12mm in from
each end and 13mm back from front of window frame and mark
where the screws will go.
We recommend drilling pilot holes for the screws using a 2mm bit.
Fix the Shoe Bases into position using 1 long screw for each Shoe
ensuring the outer edge is to the outside of the window.
Installing outside the window frame…
We recommend using a spirit level for vertical and horizontal alignment.
Place the blind in position and mark the top corners of the blind.
Measure 4mm down and 5mm in from the top corners and mark the
location of the L bracket outer screws (ensure screws are at least 16mm
from window opening).
The measurement from this screw to the screw on the bottom brackets is
the ‘order height’ minus 8mm (order height can be found on the outside
of your box). And mark with a pencil.
Place L brackets in position and mark where the other screws will go.
We recommend drilling pilot holes for the screws using a 2mm bit.
Fix the L brackets into position using 2 long screws for each bracket.
Fix the Shoe Bases onto the L Brackets using 1 short bolt for each shoe,
ensuring the outer edge is to the outside of the window.
2Support Brackets
(only for blinds over 1270mm)
Wall Plugs for Brick
or Cement using
a 6mm bit
(if requested)
Inside Video Outside Video
Required Tools
Shoe Base
(For Headrail and
Bottom Rail)
Installation
L Bracket
(Outside Install)
Handle
Short Bolt
Long Screws for
Wood
Inner Edge Outer Edge
centre of
blind width
#65101-10235-G
Extension Pole
(if requested)
centre of
blind
Top centre of blind
Top centre of blind
L Bracket Cover
(Outside Install)
Shoe Slider
(Attached to blind)
Difficulty: ★★☆☆☆
1
Installing inside the window frame…
Mark the centre of the window opening at top and bottom
and mark 13mm back from front of window frame.
Measure 9mm to the left and 9mm to the right of the centre mark,
this is the position of the screws for the centre Shoe Bases.
We recommend drilling pilot holes for the screws using a 2mm bit.
Place Shoe Bases into position ensuring the outer edges meet in the centre.
Fix the Shoe Bases into position using 1 long screw for each Shoe.
Installing outside the window frame…
Mark the centre of the window opening at the top and bottom of the window frame.
Measure 5mm to the left and 10mm to the right of the centre mark, this is the position
of the inner screws for the centre L brackets.
Place L brackets in position and mark where the outer screws will go.
We recommend drilling pilot holes for the screws using a 2mm bit.
Fix the L brackets into position using 2 long screws for each bracket.
Fix the Shoe Bases onto the L brackets using 1 short bolt for each
Shoe ensuring the outer edges of Shoes meet in the centre.
Slide bracket covers over the bracket screws.
Note: 2 shoes provided for top only, as per diagram.

Please note all blind cords are interconnected.
Ensure the cords are not crossed or tangled.
Place Shoe Sliders into centre of Shoe Bases
and slide towards the outer edge of Shoe as
per diagram to the right.
4Install Blind
Please write a review on our
website at…
www.venetablinds.com.au
Feedback?
We would love to know how you
went with your installation…
Installation
continued…
How to install, operate and maintain your
Smartfit Honeycomb Blind (25mm Cell)
Great Job… Enjoy your new Veneta Blinds!
Operating your
Blind
Lower and raise the blind using the handles on the top and bottom rails.
Note the blind will close firmly at the top utilising the inbuilt magnets.
Maintaining your
Blind
1Dusting
Dust can be removed using a feather duster or vacuum with brush attachment on low suction.
2Spot Cleaning
Use a warm damp cloth or a mild detergent for tougher stains.
Dab the affected area, but do not rub the fabric. Finish with just a warm damp cloth.
Allow the fabric to dry in the lowered position.
3Ultrasonic
If ultrasonically cleaning the blind please specify that a mild solution must be used.
Note the rails should never be immersed in liquid.
Slide handle onto the top and bottom rails.
3Attach Handle
2