VENETA 65101-40160-D Instruction sheet

Mounting Brackets
(for Outside Mount)
19mm Round Head
Screw
Traditional Hold
Down Bracket
(for Inside Mount)
Required Tools measuring
tape
drill with
2mm bit
phillips bit or
screwdriver
pencil knife
How to install your
#65101-40160-D
Cordless
(Roller Blinds with Raceway) Difficulty:
Included Hardware
The hardware can be found in
the small hardware box included
with your blind.
1Blind Bracket Installation
Handle
Installation
continued…
How to install your
#65101-40160-D
Cordless
(Roller Blinds with Raceway) Difficulty:
2
32mm
Hexagon Screw
(for Mounting Bracket)
①
②
③
Attach the blind brackets and extensions into the two ends of the raceway. Please decide
the tension dial is at the left or right side of the blind first, the side with the tension dial
should use the tension dial end bracket.
Make sure the extension bolt locks into the raceway’s dedicated hole.
First fit the blind bracket cover over the blind bracket. Install the raceway into the window
opening.We recommend securing the screws into the middle holes of the raceway first.This
would allow you to adjust the raceway left or right if required. Once the correct position has
been located, secure the screws for the holes.
Take care that the distance between the 1st screw and the window edge is at least 19mm.
1
2Blind Installation and Removal
Installing outside the window frame
Installing inside the window frame
1Blind Bracket Installation
①
②
Measure 75mm in from top left and top right of
where the blind will sit, and mark where the
screws will go.
When installing the mounting bracket, the
distance from the bracket’s mounting hole to the
edge of the window frame should be at least
19mm.
Make sure all brackets line up with each other
horizontally. Each bracket will require two 32mm
hexagon screws for the installation.
If more brackets are supplied, space them
evenly between the first two brackets.
3
4
19mm
Before installing the shade into the mounting brackets, please locate the lock pin in the
shade bracket on the end plug side. Slide the pin downward into the end plug to prevent
the shade from falling.
Insert the back edge of the raceway into the back plastic part of the bracket, and then
turn the raceway upwards so that the front rib of the raceway snaps into the bracket.
There are two ways to attach the shade to mount brackets....
A.
Front view… Side view…

* The blind must be installed on the brackets when
adjusting.
Installation
continued…
Please write a review on our
website at…
www.venetablinds.com.au
Feedback?
We would love to know how you
went with your installation…
How to install your
#65101-40160-D
Cordless
(Roller Blinds with Raceway) Difficulty:
3
How to install, operate and maintain your
#65101-40160-D
Cordless
(Roller Blinds with Raceway) Difficulty:
4
5Cordless Operation
Use the “hook” portion to hook
the handle to lower the blinds.
Place the U- shape channel of
pole under the handle and push
up to lift the blinds.
Great Job… Enjoy your new Veneta Blinds!
1Dusting
Dust can be removed using a feather duster or vacuum with brush attachment on low suction.
2Spot Cleaning
Use a warm damp cloth or a mild detergent for tougher stains.
Dab the affected area, but do not rub the fabric. Finish with just a warm damp cloth.
Allow the fabric to dry in the lowered position.
Maintaining your
Blind
Installation
continued…
Pull the handle downwards or upwards
and the blind will be lowered or raised.
The tension in our cordless roller blind can be adjusted to
provide optimal light control and to ensure easy and
dependable operation on a variety of window types and
sizes. If a cordless blind begins to slide down on its own or it
fails to roll up, the issue can be easily fixed by turning the
adjustment dial towards “+” to increase the tension.
Conversely, if the cordless blind cannot stop at the desired
height and tends to roll up by itself, the tension can be
decreased by turning the adjustment dial towards the “-”.
Need HELP?
Call our
Customer Service team
for assistance
1300 836 382
4Hold Down Brackets Installation (optional)
Use 19mm round head screw to secure each bracket.
Snap the front rib of the raceway into the bracket, and then turn the raceway backwards
and upwards so that the back of the raceway is stuck to the back plastic part of the
bracket.
Attach Handle to Hem Bar…
Step 1: Turn over hem bar and you can see a label attached at the center of the hem bar.
Step 2: Align the center of the bottom of the handle with the label.
Step 3: Hook the handle to the hem bar from top to bottom.
Step 4: Press the handle from top to bottom to make the top of the handle clip into the hem bar.
Step 5: Tear off the label from hem bar.
Handle installation and Removal
①
③
Label
The center of handle should
be aligned with the label.
④ ⑤
Remove handle from hem bar…
Use straight screwdriver to pry the bottom of handle
from hem bar and then the handle can be removed.
③
③
②
②
①
①
Use a tool to push back the front or back plastic part of the brackets.
Turn the back side of the raceway downward so that it detaches from the bracket.
Finally remove the raceway by pulling downward from the brackets.
or
Removal of the Blind….
②
3
B.