Victory 4x4 ADVENTURE BED RACK Configuration guide

ADVENTURE
BED RACK
Thank you for purchasing from Victory 4x4! Checkout our website, victory4x4.com for other great o-road
products. Be sure to rate and review our product online. If you have any questions or are missing parts, please
don’t hesitate to call us at 269-459-8447!
INSTALL INSTRUCTIONS
Please read the mounting instructions below carefully before attempting to install.
Be sure to check out the install video on the product page, if available.

INCLUDED HARDWARE
8x
28x
3/8”-16 X 3/4” Long
Carriage Bolt
3/8”-16
Flange Locknut
5/16”-18
Flange Locknut
28x
8x
5/16”-18 X 1-1/2”
Carriage Bolt

INCLUDED PARTS
2x 2x2x 4x
4x
4x

1.
ASSEMBLY
2. If you do not have the trail rail system, you will need to clamp the legs
to the side of the bed. For this method, we recommend putting the rack
together before putting the legs on the bed of the vehicle. Only do this if
you can get help liing it into place aer it is assembled. If you are putting
the rack together alone, attach the legs to the bed first. See step 6 on page
8 for more instructions on this.
How you begin the install depends on whether or not you have a trail rail
system in the bed of your vehicle. If you do, insert a provided 5/16”-18 x
1-1/2” carriage bolt through each hole in the small rectangular spacer and
slide that into the trail rail. Do that 3 more times, then you can mount the
legs of the bed rack using the 5/16”-18 locking flange nuts. Leave these
somewhat loose for now so you can adjust the width in order to fit the side
crossbars in step 4.

ASSEMBLY
3. Next, mount the open-ended crossbars between the each of the front and
rear legs using the provided 3/8”-16, 3/4” long carriage bolts and
3/8”-16 locking flange nuts on the inside. Assemble as shown in the
orientation below. You may need to adjust the width and position of the
middle crossbar depending on your vehicle.

ASSEMBLY
4. Next, connect the front and rear legs using the wider crossbar using the
provided 3/8”-16 x 3/4” carriage bolts and 3/8”-16 locking flange nuts. This
bar mounts to the outside of the front and rear legs and gives you a few
dierent mounting options to choose from. The flanges should be toward
the inside of the rack. If you are assembling the rack on the bed, you may
need to slide the legs forwards or backwards in order to attach the bar.
Once the bar is attached you can tighten the legs fully into place. Try to
tighten each bolt evenly in order to best secure the bed rack. Once secure,
make sure to go back and tighten down your legs to the bed now that the
width is correct.

ASSEMBLY
5. Next, mount the remaining bars vertically between the two top horizontal
crossbars. Choose which slots you want to mount to in the top crossbar
and then use the provided 3/8”-16 x 3/4” carriage bolts and 3/8”-16
locking flange nuts to mount them in position. The open side should be on
the bottom with the flange pointing down, as shown below.

ASSEMBLY
6. Finally, if you need to clamp the legs to the bed, place the assembled bed
rack into the bed and loosely attach the c shaped bracket to the back of
the bottom of each of the legs using the 5/16”-18 x 1-1/2” carriage bolts
and 5/16”-18 locking flange nuts. Make sure the 90-degree bend is on the
bottom and the carriage bolts go through the back side of the c shaped
bracket. Finally, push the c shaped brackets up until the edge of the bed is
between the brackets and the bottom of the legs and tighten them all into
place, clamping the bed rack onto the bed. Try to tighten each bolt evenly
in order to best secure the bed rack. If you are doing this step before
assembling the rack, it may be easiest to attach the c shaped brackets to
the legs before setting them into place.

DIMENSIONS
MINIMUM
MAXIMUM
NOTE: The 5’ rack need 48” long of trail rail or clampable bed space in order
to mount, while the 6’ rack needs 60” long of trail rail or clampable bed
space to mount.