Victory 4x4 V4RRK User manual

5TH GEN 4RUNNER
FULL ROOF RACK...............................2
5TH GEN 4RUNNER
STANDARD ROOF RACK....................13
4TH GEN 4RUNNER
ROOF RACK......................................23
3RD GEN 4RUNNER
ROOF RACK......................................34
TABLE OF CONTENTS

5TH GEN 4RUNNER
FULL ROOF RACK
Thank you for purchasing from Victory 4x4! Check out our website, victory4x4.com for other great o-road
products. Be sure to rate and review our product online. If you have any questions or are missing parts, please
don’t hesitate to call us at 269-459-8447!
INSTALL INSTRUCTIONS
Please read the assembly instructions below carefully before attempting to install.
Check out the install video on the product page for factory rack disassembly.

INCLUDED HARDWARE
50x
22x
50x
1/4” ID
Washer
1/4"-20
Serr. Flange Nut
1/4"-20 X 3/4"
Button Head 4x 1/4"-20 X 3/8" Button Head
Included with light bar
cutout option.
4x 1/4"-20
T-Nut
Included with light bar
cutout option.
8x M8
Washer
8x 25mm M8
Button Head 8x 1/2” Rubber
Push-in Bumper

INCLUDED PARTS
2x 8x 1x 1x 1x
Or
1L/1R
2x
1L/1R1L/1R
Included with light
bar cutout option.

1Assemble the rack on the ground. Start by mounting the crossbars
between the 2 side rails. For this, use the1/4”-20 X 3/4” button head bolts
and the 1/4” ID washers (2 per bar per side). Make sure the machined slot
in the rail of the crossbar is facing up, so that you can easily add t-nuts to
mount your gear.
ASSEMBLY

ASSEMBLY
2Next, mount the strip of trim to the bottom edge of the front fairing. Start
just to the outside of the peak of the bottom edge and continue until it
reaches the equivalent point on the other side of the fairing. Cut o any
extra. Then, cut the extra in half and mount the 2 pieces onto the bottom
edge of the rear fairing wherever it contacts the roof of the vehicle.

ASSEMBLY
3Next, mount the front and rear fairings. To do this, use the1/4”-20 X 3/4”
button head bolts, 1/4” ID washers, and 1/4”-20 serrated flange nuts. The
front fairing will need 3 of each per side and the rear fairing will need 2 of
each per side. When mounting the front fairing, adjust it all the way up to
avoid contact with the roof and tighten for now.

ASSEMBLY
4Next, attach the mounts to the assembled roof rack using the 1/4”-20 X
3/4” button head bolts, 1/4” washers and 1/4” serrated flange nuts. Set the
mounts at the lowest position and tighten them for now.

ASSEMBLY
5Next, attach the mid and rear mounts to the roof of the vehicle. Start by
circling each hole on the roof with RTV. This will seal the mounting surface.
Then, press the rubber bumpers into the bottom of the front mounts
(start one edge and twist them into place) and set the assembled roof
rack into place on the roof. Next, cover each mounting hole with RTV. Use
enough that the bolt will have to pass through it when tightening into the
roof. Bolt the mid and rear mounts to the roof using the M8 button head
bolts and washers. Start all of them by hand and then go back and tighten
fully.

ASSEMBLY
6With the mid and rear mounts bolted firmly to the roof, adjust the position
of the rack by loosening the mounting bolts on the side rail until there is
and equal gap between the bottom of the side rails and the roof down the
length of the vehicle. Then re-tighten only the mid and rear mounts into
place.
7Next, pull up slightly on the front of the rack, and push the front mounts
down into the channel. Make sure the rubber bumpers are seated fully
in the channel before tightening them. This allows for the mid and rear
mounts to help hold the front mounts against the roof and prevents any
type of movement.
8Finally, push the front and rear fairings tight against the roof and tighten
everything fully into place. We recommend applying clear 3M paint
protection film to the roof of the vehicle anywhere the edge trim/fairings
make contact with the roof. This will protect the paint from dirt/debris
over time. If you are unable to get the front fairing down tight to the roof,
you may need to adjust the overall height of the rack at the mid and/or

40” LIGHT BAR
ASSEMBLY
1Slide 2 t-nuts into each of the channels on the top side of the front-most
crossbar using the slots. Then, place each light bar mount over one pair of
t-nuts and loosely bolt it in place using the 1/4”-20 X 3/8” button heads.
2Next, place your light bar between the mounts and mount it in the slots
using the hardware provided with the light bar. Aer that is firmly in
position, make any adjustments to the positioning necessary to center the
light bar on the rack. Depending on the rack and light bar, you may need to
adjust the position of the cross bar in its slot as well.

DIMENSIONS

5TH GEN 4RUNNER
STANDARD ROOF RACK
Thank you for purchasing from Victory 4x4! Check out our website, victory4x4.com for other great o-road
products. Be sure to rate and review our product online. If you have any questions or are missing parts, please
don’t hesitate to call us at 269-459-8447!
INSTALL INSTRUCTIONS
Please read the assembly instructions below carefully before attempting to install.
Check out the install video on the product page for factory rack disassembly.

INCLUDED HARDWARE
36x
16x
36x
1/4” ID
Washer
1/4"-20
Serr. Flange Nut
1/4"-20 X 3/4"
Button Head
8x M8
Washer
8x 25mm M8
Button Head

INCLUDED PARTS
2x
1L/1R
2x 5x 1x 1x

1Assemble the rack on the ground. Start by mounting the crossbars
between the 2 side rails. For this, use the1/4”-20 X 3/4” button head bolts
and the 1/4” ID washers (2 per bar per side). Make sure the machined slot
in the rail of the crossbar is facing up, so that you can easily add t-nuts to
mount your gear.
ASSEMBLY

ASSEMBLY
2Next, mount the strip of trim to the bottom edge of the front fairing. Start
just to the outside of the peak of the bottom edge and continue until it
reaches the equivalent point on the other side of the fairing. Cut o any
extra. Then, cut the extra in half and mount the 2 pieces onto the bottom
edge of the rear fairing wherever it contacts the roof of the vehicle.

ASSEMBLY
3Next, mount the front and rear fairings. To do this, use the1/4”-20 X 3/4”
button head bolts, 1/4” ID washers, and 1/4”-20 serrated flange nuts. The
front fairing will need 3 of each per side and the rear fairing will need 2 of
each per side. When mounting the front fairing, adjust it all the way up to
avoid contact with the roof and tighten for now.

ASSEMBLY
4Next, attach the mounts to the assembled roof rack using the 1/4”-20 X
3/4” button head bolts, 1/4” washers and 1/4” serrated flange nuts. Set the
mounts at the lowest position and tighten them for now.

ASSEMBLY
5Next, attach the mounts to the roof of the vehicle. Start by circling each
hole on the roof with RTV. This will seal the mounting surface. Then, set
the assembled roof rack into place on the roof. Next, cover each mounting
hole with RTV. Use enough that the bolt will have to pass through it when
tightening into the roof. Bolt the mounts to the roof using the M8 button
head bolts and washers. Start all of them by hand and then go back and
tighten fully.